Monogram ZDBG240S User manual

Installation
Instructions
Wine Chiller
and
Beverage Center
Design Guide
With Installation Instructions

Safety Information
2
CONTENTS
Design Guide
The Installation Space ............................ 3
Product Clearances ................................ 3
Side-by-Side Installation ........................ 3
Installation Instructions
Tools, Hardware ....................................... 4
Grounding the Product ........................... 4
Staining Wood Drawer Fronts ............... 4
Step 1, Remove Packaging .................... 4
Step 2, Reverse Door Swing .................. 5
Step 3, Leveling ........................................ 6
Step 4, Connect Power ........................... 6
Step 5, Slide Product into Cutout .......... 6
Step 6, Install Nameplate ....................... 6
Step 7, Set Temperature Controls ......... 6
Template for Nameplate ...... Back Cover
BEFORE YOU BEGIN:
Read these instructions completely and carefully.
IMPORTANT – Save these instructions
for local inspector’s use.
IMPORTANT –Observe all governing
codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
WARNING –This appliance must be
properly earthed. See “Electrical Supply”, page 4.
If you received a damaged wine chiller or beverage
center, you should immediately contact your dealer
or builder.
Skill Level – Installation requires basic mechanical
skills. Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the Warranty.
WARNINGS:
• Use this appliance only for its intended purpose.
• Immediately repair or replace electrical service
cords that become frayed or damaged.
• Unplug the unit before cleaning or making repairs.
• Repairs should be made by a qualified service
technician.

596 mm
875 mm
580 mm
Locate
Outlet
875–890 mm
603 mm Min.
229 mm
Max.
267 mm
38 mm
610 mm
Design Guide
THE INSTALLATION SPACE
The cutout depth should be 600 mm
The cutout dimensions shown allow for a full door
swing and access to the pull-out racks when installed
as a built-in in standard 600 mm deep cabinets.
• The wine chiller, wine reserve and beverage center
can be installed freestanding.
• If installing between frameless cabinets, a 13 mm
wide filler strip or side panel may be needed on
hinge side. The filler strip will act as a spacer
between the case and adjacent cabinet door swing.
The width of the opening must include the filler
panels. NOTE: The door should protrude 25 mm
beyond the surrounding cabinets.
Additional Specifications
• A 230V 50Hz, 13–16 amp power supply is required.
An individual properly earthed branch circuit or
circuit breaker is recommended. Ensure a properly
earthed electrical supply outlet has been installed
into the back wall as illustrated.
PRODUCT CLEARANCES
The wine chiller and beverage center is factory set for
a 110°door swing.
When installed in a corner:
• Allow 100 mm minimum clearance on the hinge side
for the 90°door swing and to allow racks to slide out.
• Allow 360 mm minimum clearance on the hinge side
for a full 110°door swing.
• The door swing is reversible on all models. If
desired, change the door swing before installation.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper access to the door.
• Do not install these products where the temperature
will go below 55°F (13°C) or above 90°F (32°C).
• Do not install where it will be subject to direct
sunlight, heat or moisture.
Black or Stainless Steel Toekick Options
• These products are shipped with a black toekick
installed. An optional stainless steel toekick is also
supplied with each product. For shipping purposes,
the stainless steel toekick is secured to the back
of the unit.
3
SIDE-BY-SIDE INSTALLATIONS
Increase storage capacity by installing two Monogram
beverage centers or wine chillers together. Or, for a
complete refreshment center, install any two of these
units together.
• A side-by-side installation requires at least a 1206 mm
wide opening. No trim kits required.
• Products must operate from separate outlet, properly
earthed receptacles.
NOTE:
Handle and
handle standoff
depth is 45 mm
875–890 mm
1206 mm Min.
38 mm
267 mm
229 mm
267 mm 336 mm
298 mm
Locate
Outlet
610 mm
360 mm Min.
to Wall
110°
530 mm
600 mm
100 mm Min.
to Wall
90°
90°Door Swing

Installation Instructions
4
TOOLS REQUIRED
• #2 Phillips screwdriver
• Adjustable wrench
PARTS SUPPLIED
• Monogram nameplate
• Hardware for changing door swing
• Optional stainless steel toekick with screws
and spacers
• Left and right side hinge covers
• Top screw hole cover
EARTHING THE WINE CHILLER
AND BEVERAGE CENTER
The power cord of this appliance is equipped with an
earthing plug which mates with a standard earthed
wall outlet to minimize the possibility of electric
shock hazard from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly earthed.
Where an unearthed wall outlet is encountered, it is
your personal responsibility and obligation to have it
replaced with a properly earthed wall outlet.
The refrigerator should
always be plugged into its
own individual electrical
outlet. This provides the
best performance and
also prevents overloading
house wiring circuits which
could cause a fire hazard from
overheated wires. Please refer
to the rating plate on the
refrigerator for the correct
voltage, wattage and frequency.
If the product plug does not
fit your outlet, the product
should be fitted with a new plug.
STEP 1 REMOVE PACKAGING
• Remove corner blocks and foam drawer stops.
• Remove all packing material, tape and protective
plastic coverings.
• Remove stainless steel toekick taped to the back
of the unit.
CAUTION: Small objects are a choke
hazard for children. Remove and discard any parts
not used.
STAINING WOOD DRAWER FRONTS
The drawer fronts are unfinished cherry wood.
During use, oil from hands may accumulate and
stain the wood.
• The drawer fronts may be stained and sealed to
match adjacent cabinetry. The tinted glass will
make the stained wood appear darker. A true color
match can be seen only when the door is opened.
• Apply the stain and sealer according to the
manufacturer’s instructions. To avoid unpleasant
odor, keep the door open to ventilate and allow
the stain/sealer to dry completely before using
the product.
Insure proper
earthing exists
before using
Earthing plug

Installation Instructions
STEP 2 REVERSE DOOR SWING
SKIP THIS STEP IF DOOR SWING SUITS THE
INSTALLATION
5
Parts Included:
• Top left case hinge
• Bottom left case hinge
• Left and right side decorative hinge cover
• Decorative hinge screw hole cover
• Torx®driver bit
Tools Required:
• Phillips screwdriver
• Electric drill
Remove the door:
• Flatten the shipping carton to use as a pad.
• Remove the 2 screws and the toekick. Set aside the
screws and toekick for final installation.
• Use the supplied Torx®bit and electric drill to
remove the 3 screws holding the top case hinge.
Lift off the hinge. (Screws will be used to install the
new hinge.)
• Lift the door off the bottom case hinge.
• Remove the bottom case hinge pin and bracket.
Rotate the door:
The handle will be on the right side of the door;
hinges will be installed on the left side of the case.
• Remove the door stop and cam riser on the original
bottom right side of the door.
• Remove the fill plug on the top right side
of the door.
• Turn the door over and reinstall the fill plug on the
new left side.
Reinstall the door:
• Install the original door stop and cam riser onto
the bottom left side of the door.
• Install the new supplied bottom case hinge pin and
bracket onto bottom left side.
• Place the door onto the bottom case hinge.
• Install the supplied left-hand top case hinge with
the 3 original screws.
• Select the hinge cover marked with an “L”.
• Peel backing off the tape inside the decorative
hinge cover.
• Press and snap the hinge
cover into place.
• Snap the screw hole cover into
place on the opposite side.
IMPORTANT: Check to be sure screws are tight and
that the door is straight and does not sag. The door
should swing freely.
Apply Monogram Nameplate:
• Install the Monogram nameplate. See instructions
and template on back cover.
Install Toekick
The toekick has a
cutout on the
left and right
sides.
Remove
the plug
on the left
side and
reinstall on
the right
side. If you
choose to install
the stainless steel toekick,
reinstall the plug on the right side of that toekick.
• Install original screws and spacers or screws and
spacers supplied with the stainless steel toekick.
Install screws through the spacer standoff, toekick
and into the base as shown.
Move Fill
Plug to
Right Side
Remove
Top Hinge
Remove
Hinge
Install
3 Hinge
Screws
Door Stop
and Cam Riser
Hinge
Pin and
Bracket
Install Covers

6
STEP 3 LEVEL
• Use an adjustable wrench to turn the leveling legs
and raise or lower the product.
• Adjust carefully; the product should be level and
plumb with cabinetry, and should align with adjacent
toekick height.
STEP 5 SLIDE PRODUCT INTO
THE CUTOUT
• Carefully, slide the unit into the opening. Be careful
not to entangle power cord.
• Make certain that the door protrudes 25 mm
beyond the surrounding cabinets.
• Check again to be sure the unit is level.
STEP 4 CONNECT POWER
• Connect power cord plug to a properly grounded
receptacle.
• Check to make sure power is on by opening the door
to see if interior light turns on.
STEP 6 INSTALL NAMEPLATE
• Follow instructions on the back page for installation
of the Monogram nameplate.
STEP 7 SET TEMPERATURE
CONTROLS
• The temperature controls are preset. Refer to
the Owner’s Manual for more information.
Allow 24 hours for temperature to stabilize.
Turn Right to Lower
Turn Left to Raise
If you skipped Step 2:
• Select the hinge cover marked “R” or “L”, depending
on door swing.
• Peel backing off the tape inside the decorative
hinge cover. Press and snap into position.
• Snap the screw hole cover into place on the
opposite side.
Installation Instructions

7
Notes

TEMPLATE FOR NAMEPLATE LOCATION
To position nameplate:
• Cut template along dotted line.
• Hold or tape template behind
glass door so that it is visible from
the front side.
• Remove backing from nameplate.
• Place nameplate onto front side of
door, matching illustration on the
template.
IMPORTANT: Nameplate must
be placed on the opposite side of
the door handle.
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance
and specifications are subject to change without notice.
Pub. No. 49-60326
Dwg. No. 197D5129P002
02-04 JR
Printed in Slovenia
Top of Badge
Cut on Dotted Line
Top of Glass Door
Door Frame Side
Upper Left
Corner of
Glass if Hinge
is on Left
DOOR NAMEPLATE LOCATION
Upper Right
Corner of
Glass if Hinge
is on Right
Door Frame Side