Monte Carlo Fan Company 5SIEP Instruction manual

Owner’s Guide and Installation Manual
Attac sales receipt to t is card and retain as your proof of purc ase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register your fixture, please visit our website www.montecarlofans.com
5SI Series Fan
Total fan weig t
UL Model No. :AC-212-002
18.55 kgs
40.81 lbs

© 2011 Monte Carlo Fan Company 1/16/2012
2
WARNING: T REDUCE THE RISK F FIRE, ELECTRIC SH CK, R INJURY T PERS NS, BSERVE THE F LL WING
READ AND SAVE THESE INSTRUCTI NS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk f Fire, Electric Shock, or Personal Injury, Mount To utlet Box Marked “Acceptable for Fan Support of
31.8 kg (70 lbs) or less” And Use Mounting Screws Provided With The utlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Re-
move Knockouts In The utlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2011 Monte Carlo Fan Company 1/16/2012
3
Insert downrod into motor yoke. Next, insert
clevis pin through yoke and downrod and secure
with cotter pin. (see inset)
Before you begin installing the fan, Switch power off
at Service panel and lock service disconnecting
means to prevent power from being switched on ac-
cidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warn-
ing device, such as a tag, to the service panel.
Install canopy and yoke cover over the down-
rod.
1
46
Thread wire through downrod with canopy and
yoke cover assembled.
5
3
Outlet box
Wood
Screws
Mounting
Bracket
Secure mounting bracket directly to a joist from
the buliding structure. Use only the appropriate
wood screws and washers included with your
fan. Caution: Wood screws must go through
into the building joist.
Note:If Installing It In The U.S., Do Not Remove
Knockouts In The Outlet Box
BUILDING
STRUCTURE
METHOD
Carefully lift fan assembly onto mounting
bracket. Rotate fan so that the notch on the
ball engages the ridge in the mounting bracket.
This will allow hands-free wiring.
8
7
Tighten both yoke set screws to further secure
downrod.
For Canadian installation and for USA fan and light
kit combinations over 35 lbs, in both flush and
downrod modes the safety cable must be installed
into the house structure beams using 3” lag
screws, washers and lock washers provided. Make
sure that when the safety cable is fully extended
the lead wires are longer than the cable and no
stress is placed on the lead wires.
Note:If Installing The Secondary Support Safety
Cable in the U.S., Do Not Remove Knockouts In
The Outlet
9Safety cable installation
Safety Ca le
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer
Warning-Risk of fire, electric shock, or personal in-
jury. The fan in this box may be either directly sup-
ported from a structural framing member of a
building and/or may be mounted to an outlet box
marked acceptable for fan support of of 31.8 kg (70
lbs) or less. Use only the hardware provided with
the fan brace or outlet box.Most outlet boxes com-
monly used for the support of lumminaires may not
be acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
Use only the hardware provided with outlet box.
2OUTLET BOX METHOD
For Installation in The U.S. only

© 2011 Monte Carlo Fan Company 1/16/2012
4
lace blade onto blade holder.
14
Install 3 screws and washers per blade and
tighten securely. Repeat for all 5 blades
15
Make wire connections to power source using
wire nuts provided. Make sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on the
other side of the outlet box.
10
For pullchain controls, follow diagram above.
Make sure that all exposed wiring is secured in-
side wire nuts. Note: Wires from house may
vary in color and may not include ground wire.
After wiring is conplete, gently push wires into
junction box with wire nuts pointing upward.
Refer to point 3 of safety tips.
11 House Fan
Black
White
Green
Black
White
Green(downrod)
Green(Bracket)
Blue
For control of fan and optional light from wall lo-
cation, follow diagram above. NOTE: A profes-
sional electrician is recommended for this type
of installation.
12
Raise the canopy up and align the two holes in
the canopy with the two holes in the hanger
bracket. Secure with two screws provided.
13
Light Switch
Fan Switch
Wall
Control
Check the motor for plastic shipping stabilizer
tabs, and remove them if they are present. At-
tach blade assembly to motor using the motor
screws and washers provided. Tighten screws
securely.
16
ush wires through center hole.Line up 2 screws
loosened from step 17.
18
Remove 1 screw and save.Loosen other 2
screws.
17 Remove
and save
this screw.

© 2011 Monte Carlo Fan Company 1/16/2012
5
Remove 3 screws and save.
21
Reinstall the switch housing using the three
screws previously removed.
22
Twist into locking position and tighten in screw
taken out. Also tighten 2 other loosened screws.
19
Connect male to female connector securely.
20
For Light Kit Installation Only
Loosen the decorative cover first, it will
make it easier to loosen the finial cap and
switch cover for light kit installation.

© 2011 Monte Carlo Fan Company 1/16/2012
6
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
3.Make sure forward/reverse switch is pushed firmly either way. Fan will not operate when
switch is in the middle.
CAUTION: Make sure main power is turned off.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are
tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off efore entering switch housing.
4.Some fan motors are sensitive to signals from Solid State variable speed controls. DO
NOT USE a Solid State varia le speed control.
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disap-
pear after this period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction
box and junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level
by selecting a point on the ceiling above the tip of one of the blades. Measure this dis-
tance from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next
blade is positioned for measurement. Repeat for each blade. If all blade levels are not
equal, you can adjust blade levels by the following procedure. To adjust a blade tip down,
insert a washer (not supplied) between the blade and blade holder at the screw closest to
the motor. To adjust a blade tip up, insert washer (not supplied) between the blade and
blade holder at the two screws farthest from the motor. Reverse the position of the
washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can
redistribute the weight and possibly result in smoother operation.
1.Check wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAUTION: Make sure main power is turned off efore entering switch housing.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
Trouble Shooting
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installa-
tion, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience
any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experi-
encing difficulty in installation, please call our Customer Service Center at the number printed on your
parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service
disconnecting means to prevent power from eing switched on accidentally. When the service
disconnecting means cannot e locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
Trou le Suggested Remedy

Jan.2012 New format
Jun.2013 Update for CUL regulation