Monte Carlo Fan Company 5SLR52 Series Instruction manual

Owner’s Guide and Installation Manual
Attach sales receipt to this card and retain as your proo o purchase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register your ixture, please visit our website www.montecarlo ans.com
5SLR52XXD-B Series Fan
Total an weight with light kit
UL Model No. : 5SLR52
10.1 kgs
22.3 lbs

© 2011 Monte Carlo Fan Company 2/1/2012
2
WARNING: T REDUCE THE RISK F FIRE, ELECTRIC SH CK, R INJURY T PERS NS, BSERVE THE F LL WING
READ AND SAVE THESE INSTRUCTI NS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk f Fire, Electric Shock, or Personal Injury, Mount To utlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The utlet Box.
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RK manufac-
tured by Rhine Electronic Co., Ltd.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Cutomer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlo ans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2011 Monte Carlo Fan Company 2/1/2012
3
Remove keeper from pin and pin
from downrod. Place keeper back on
pin and save for later.
5
Loosen the 2 set screws till you can
not feel them on inside of yoke.
4
Place canopy on downrod. (as shown)
6
Before you begin installing the fan, witch
power off at ervice panel and lock service dis-
connecting means to prevent power from being
switched on accidentally. When the service dis-
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per-
sonal injury, mount to outlet box or supporting
system acceptable for fan support. (Mounting
must support at least 35 lbs.)
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet box is securley
fastened by at least two points to a structural
ceiling member ( a loose box will cause the fan
to wabble). Use only the screws provided
with the outlet box.
3
21
Place downrod into fan yoke.
9
Thread leadwires and safety cable
through downrod. (as shown)
8
Place yoke cover on downrod. (as
shown)
7

© 2011 Monte Carlo Fan Company 2/1/2012
4
Hang assembled fan from the mounting bracket
installed to ceiling in previous step. Make sure
the fan is hanging straight. Rotate fan until the
tab on the Mounting bracket engages the slot on
the Downrod Ball. This must be done to pre-
vent the fan body from rotating when the blades
are in motion.
14
Install the keeper to pin.
11
Tighten the 2 set screws on the yoke
once the downrod is in place.
12
Align the hole in the downrod with
the hole in the yoke. Insert th pin
through the yoke and downrod until
the point appears on the other side.
10
Pull down yoke cover.
13
Fan and light kit combinations over 35 lbs, in
both flush and downrod mode the safety
cable must be installed into the house struc-
ture beams using the 3” lag screws,washers,
and lock washers. provided. Make sure that
when the safety cable is fully extended the
lead wires are longer than the cable and no
stress is placed on the lead wires.
15 afety cable installation
Safety Cable
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer
et dip switches on the Remote Transmitter and Re-
mote Receiver to the same settings. This must be
done so the units will communicate properly. If you
have other fans you can set to control from one
transmitter by setting both receivers the same as the
transmitter. If you have more than one fan with re-
mote. You can set the dip switches to different posi-
tions to have seperate control.
17
Remote Transmit-
ter Dip switches
Remote Receiver Dip
switches
Install remote receiver by sliding into opening
in the Mounting bracket. Make sure that the
dip switches on the Transmitter and the Re-
ceiver are set to the same position.
18
Make sure the studs protruding from the
bottom of the Mounting bracket are in-
stalled with threads all the way through
the bracket.
16

© 2011 Monte Carlo Fan Company 2/1/2012
5
Attach glass by locating dimples in
light kit with the groves in glass and
twist clockwise till tight.
27
Attach blades to motor using screws
and washers in hardware bag and
tighten screws securely.
22
Connect white wire from fan to white
wire from light fixture. Then plug blue
wire from fan to red wire form light
fixture.
24
Remove 1 screw and loosen the
other 2 screws. ave screw.
23
Make wire connections to power source using
wire nuts provided. Make sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on
the other side of the outlet box. plices after
being made should be turned upward and
pushed carefully.
20
Make wiring connections as indicated above.
White from fan to white from remote marked
N. Blue from fan to blue from remote marked
light. Black from fan to Black from remote
marked L. White from house to white from re-
mote marked AC N . Black from house to
Black from remote marked AC L. Connect all
green ground wires to Ground wire from
House.
19
white
black
Lift canopy and install knurled nuts as
shown. Tighten the knurled nuts securely.
The canopy should adjust for any irregu-
larity in the ceiling or Outlet box.
21
Attach light fixture onto the plate on
motor assembly, aligning its keyhole
slots with the screws on plate and
twist clockwise till lock. Re-install the
screw removed in step 23. Tighten all
screw securely.
25
Attach GU24 2x18W CFL bulbs and secure
by twisting clockwise. Bulbs included.
WARNING: U E MAXIMUM GU24 18
WATT LI TED BCFL( ELF-BALLA TED
COMPACT FLUORE CENT LAMP) ONLY,
NOT U ING BCFL WILL OVERHEAT THE
UNIT AND CAU E DAMAGE TO THE UNIT
OR THE FAN WHICH THE UNIT I IN-
TALLED TOGETHER.
26

© 2011 Monte Carlo Fan Company 2/1/2012
6
Remove battery cover. Install 12V battery into
wall remote. Duracell MN21 / Eveready A23 / GP
23A all 12V.Attach cover of remote by placing
over buttons and snap the battery cover in
place.
Place face plate over battery compartment and
buttons. Place remote over 2 pins on front
cover. Attach cover of remote by placing over 4
pins and snapping into place.
29
28 HAND HELD IN TALL
Install wall control unit to outlet box
using machine screws provided.
30 WALL MOUNT IN TALL
Attach front cover to wall control
with screws provided. nap battery
cover in place.
31

© 2011 Monte Carlo Fan Company 2/1/2012
7
Remote Control ransmitter Features
FAN SPEED Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for
high. To turn fan off press square”.
LIGH To turn light on, press light once quickly. To turn off, press once quickly
while light is on.
FORWARD/REVERSE Depress rev button allow a few seconds for remote to
change rotation direction with fan running.
HIGH PEED
MEDIUM PEED
LOW PEED
FAN OFF ETTING
(Turns fan off only)
FAN REVER E (Press
once to change direc-
tion of the fan) Fan
must be running to
reverse.
LIGHT ON/OFF
LED LIGHT

© 2011 Monte Carlo Fan Company 2/1/2012
8
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
CAU ION: Make sure main power is turned off.
3.Check to make sure the dip switches from the transmitter and receiver are set on the
same frequency.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAU ION: Make sure main power is turned off before entering switch housing.
4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware
are finger tight. Check to be sure light bulb is tight in socket and not touching glass shade(s).
If vibration persists from glass, remove glass and install a 1/4" wide rubber band on glass
neck to act as an insulator. Replace glass and tighten screws against rubber band.
5. ome fan motors are sensitive to signals from olid tate variable speed controls.
DO NO USE a Solid State variable speed control.
6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear
after this period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box
and junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by se-
lecting a point on the ceiling above the tip of one of the blades. Measure this distance from
blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-
tioned for measurement. Repeat for each blade. If all blade levels are not equal, you can ad-
just blade levels by the following procedure. To adjust a blade tip down, insert a washer (not
supplied) between the blade and blade holder at the screw closest to the motor. To adjust a
blade tip up, insert washer (not supplied) between the blade and blade holder at the two
screws farthest from the motor. Reverse the position of the washer if blades mount from top
of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can re-
distribute the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CAU ION: Make sure main power is turned off before entering switch housing.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
TROUBLE HOOTING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check this Trouble hooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation,
please call our Customer ervice Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service discon-
necting means to prevent power from being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
WARNING: U E MAXIMUM GU24 18 WATT LI TED BCFL( ELF-BALLA TED COMPACT FLUO-
RE CENT LAMP) ONLY, NOT U ING BCFL WILL OVERHEAT THE UNIT AND CAU E DAMAGE TO
THE UNIT OR THE FAN WHICH THE UNIT I IN TALLED TOGETHER.
rouble Suggested Remedy

Feb.2012 New format