montpellier TCH261 User manual

Cod:0103087495-00.02
Telescopic Cooker Hood
TCH261 / TCH291 - 60/90cm

Thank you for choosing this Montpellier 7HOHVFRSLF&RRNHU+RRG.
Our +RRGVhaYH been designed to provide you with the best combination of style, reliability and performance to
give you years of trouble-free use.
You may be familiar with a similar product, but please take time to read these instructions carefully before installing
or using your &RRNHU+RRG to ensure you get the most from your purchase.
We recommend that you keep this manual in a safe place for future reference.
Your &RRNHU+RRGis covered by a comprehensive two year Parts & Labour
Guarantee. In the unlikely event that you experience a problem with your +RRG,
you can rest assured that you are fully protected against WKHFRVWRIUHSDLUVIRU
WKHILUVWPRQWKV3OHDVHQRWHWKDWDQ\FODLPPXVWbe accompanied by the
model reference number, serial number and proof of purchase.
To activate your guarantee, you will need your product serial number. This can
be found on the rear of the machine.
There are two ways to register your Guarantee:
•Online: Visit the Support page on our website and complete the online Product
Registration form. www.montpellier-appliances.com
•By Post:6LPSO\GHWDFKDQGƮOOLQWKHIRUPSURYLGHGDWWDFKDVWDPSDQGVHQG
it in the post. Don’t forget to include your e-mail address so that we can send
FRQƮUPDWLRQWKURXJKWR\RX
Welcome
Note: We are unable to take registrations over the phone.
ACROSS ALL OUR MODELS
YEAR
GUARANTEE
PA R T S & LA B O U R
www.montpellier-appliances.com

3

Using your Extractor
For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run
for approximately 15 minutes after the end of cooking.
Control Panel
The telescopic canopy controls the electric power.
panel back in.
At either side of the panel are switches controlling the fan speed and the light.
Light: switch button to "I" to illuminate the light.
Speed: switch to "I" for low speed and "II" for high speed
Fig. 1
Motor switch Lamp switch
4

Care and Maintenance
IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING
OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE
ELECTRICITY SUPPLY.
Cleaning
Use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will
scratch the surface and could erase the control panel markings.
solution of water and mild detergent and drying to a shine with a clean
cloth.
The grease filter should be kept clean to minimise the risk of fire.
You should remove and clean the grease filter with hot soapy water at
least once a month.You can also wash the grease filter in a
dishwasher, ensuring that you place it in an upright position to prevent
damage from other items in the dishwasher. After rinsing and drying,
replace the filter.
To remove the grease filter, push in the button on the handle and then
pull down on the filter at the front. When you have released it at the
front, pull out the filter. To replace the grease filter, repeat the above
steps in reverse.
Please note:
Cleaning the grease filter in the dishwasher may lead to discolouration.
This is normal and does not constitute a fault with the appliance.
Fig. 2
5

NOTE: Replacement ofthe LED lamp must becarried out
by a qualified electrician.
IMPORTANT: DO NOT PERFORM MAINTENANCE
OR CLEANING OF THE EXTRACTOR WITHOUT FIRST
SWITCHING OFF THE ELECTRICITY SUPPLY.
1. According fig.4-I take down grease filters.
2. According fig.4-II take down LED lamp.
3. According fig.4-III,install new LED lamp.
4. Installation grease filters.
The light is designed for use during cooking and not for general room
illumination. Extended use of the light can reduce its life span. Please
contact your local retailer in order to purchase a new LED lamp when
replacing a damaged or a faulty one.
Fig. 4-I
Fig. 4-II
Fig. 4-III
TCH261 / TCH291 1x4W MAX
6

FUSE 5A
PROTECTION LINE
5A Fuse is installed inside the plug to protection line.
7
44W

service engineer
8

Before installing
As shown in Figure 7, fix the wide retainer plate (16mm) to the
machine with 2 screws.
At this me, the extension length of the fixing plate should be
10mm, and the two screws pass through the sliding plate
long hole and fixed on the fixing plate, adjust the sliding plate
to the proper posion, and ghten the screw nail. This state
decorave panel extends from 10mm to 24mm.
As shown in Figure 8, fix the etainer plate narrow side (10mm)
to the machine with 2 screws.
At this me, the extension length of the fixing plate should be
16mm, and the two screws pass through the sliding plate long
hole and fixed on the fixing plate, adjust the sliding plate to
the proper posion, and ghten the screw nail. This state
decorave panel extends from 16mm to 30mm.
Sliding plate
Fixing plate
Sliding plate
Fixing plate
the cooker hood, please
on the air outlet of the hoods.
Fig.5
Fig.6
Information
installation.
Decorative strip installation
9
Fig.7
16
16
10
10
Fig.8

the stencil to drill out 4 holes in the cabinet. Insert rawl plugs
and screws to correspond with the 4 holes.
on either side should be less than 2mm. Ensure that there is no
gap between the top of the hood and the cabinet.
The gap at the back should be no more than 10mm and the plug
must be accessible.
Fig.7
Information
When cutting or drilling into wall or ceiling, do not damage
electrical wiring or other hidden utilities.
Fig.8
ø7
4x
1
443
ø8
4
88
10
Without decorative strip 282
Include decorative strip 292~310
(Without cabinet door)
Without decorative strip 282
Include decorative strip 292~310
(Without cabinet door)
TCH261
Fig.7
1
743
330
180
140
140
ø8
4
88
TCH291