Mooer Phaser Player User manual

Main Features
Over view
Precautions
Phaser Player is a high quality Phaser with 3 different
tones. Built into a convenient mini expression pedal
for easy, on the fly, speed control. It's equipped with
MOOER's unique pressure sensing footswitch circuit
and has 3 different methods of activation.
Power Supply
Connections
Always turn off the power of this and all other equipment
before connecting or disconnecting, this will help prevent
malfunction and / or damage to other devices. Also make
sure to disconnect all connection cables and the power cord
before moving this unit.
Cleaning
Clean only with a soft, dry cloth. If necessary, slightly moisten
the cloth. Do not use abrasive cleanser, cleaning alcohol,
paint thinners, wax, solvents, cleaning fluids, or chemical-
impregnated wiping cloths.
Interference with other electrical devices
Radios and televisions placed nearby may experience reception
interference. Operate this unit at a suitable distance from
radios and televisions.
Location
To avoid deformation, discoloration, or other serious damage,
do not expose this unit to the following conditions:
Direct sunlight
Magnetic fields
Heat sources
Strong vibrations or shocks
Excessive dusty or dirty location
Extreme temperature or humidity
High humidity or moisture
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
FCC certification
Please Read Carefully Before Proceeding
Please connect the designated AC adapter to an AC outlet
of the correct voltage. Please be sure to use only an AC
adapter which supplies 9V DC(±10%), , center
negative. Unplug the AC power adapter when not in use or
during electrical storms.
Three different Phaser types
Expression pedal controls rate of Phase filter
Equipped with MOOER's unique pressure
sensing footswitch
TrueBypass switching
Rugged metal housing
Expression Phaser Pedal

Pedal layout Modes and Switching
Part No:620010617
1. LED：
Indicates the on/off status of the effect pedal
2. Input jack :
1/4” audio jack for connecting to the input
device or instrument.
3. Output jack :
1/4” audio jack, effect output for connection
to amp or other devices
4. DC in power jack:
Input for power supply, use a 9V DC regulated
power supply , center pin negative.
5. Pedal extension rings:
Can be extended to increase pedestal surface
area and increase comfort
6. Pressure sensing pads：
Activates the effect by detecting the presence
of your foot. Front sensing pad is used to change
Phaser mode. Rear sensing pad is used to change
switching mode.
7. Expression Pedal:
Controls the rate of the phaser effectin mode 1&2.
Toe down increases the rate and heel down decreases
the rate. Adjusts the filter frequency in mode 3.
PHASER MODES
The PH WAH has three different Phaser modes, each with a
different sound.
To change Phaser mode:
Press and hold the toe pressure sensing pad
while the pedal is connected to power
Disconnect the power whilst continuing to hold
the sensing pad
Reconnect power
The LED's will flash BLUE to confirm the mode has changed.
Flashing once means mode 1, flashing twice means mode 2,
flashing three times means mode 3. Release the pressure
sensing pad to resume operation.
The LED's will flash RED to confirm the mode has changed.
Flashing once means mode
1, flashing twice means mode
2, flashing three times means mode
3. Release the pressure sensing pad to resume operation.
SWITCHING MODES
PH WAH has 3 different types of switching.
1.Touch the pressure sensing pads with your foot
to turn on the effect. Release your foot from the
pedal to turn off the effect
2.Double tap the pressure sensing pads to turn on
the effect. The effect will remain on untill you
double tap the pressure sensing pads for a second time
3.In this switching mode you can use both
techniques mentioned above for switching the
effect on and off
To change switching mode:
Press and hold the heel pressure sensing pad
while the pedal is connected to power
Disconnect the power whilst continuing to hold
the sensing pad
Reconnect power
*Notes：Any specification’s update will not be amended in
this manual.
Input：1/4” mono audio jack.（Impedance: 1M Ohms）
Output：1/4” mono audio jack（Impedance: 100 Ohms）
Power requirements: AC adapter 9V DC , center negative.
Highly recommend to use Mooer Micro Power.
Current Draw：130mA
Dimensions：128mm(D) x 55mm(W) x 48mm(H)
Weight：460g
Accessories：Owner ’s Manual
2
1
3
4
56
1
7
Specifications