Moons' TSM11 Series User manual

TSM
TSM11 Quick Setup Guide
Requirements
You will need these items to set-up the TSM11:
• A 15 - 30 volt DC (24VDC nominal) power supply
• Download Step-Servo Quick Tuner software from MOONS’
website
• A PC running Windows XP, Vista, Windows 7 or Windows 8
(32-bit or 64-bit)
• A mating cable(for power, I/O and communication
connection, included in package)
• A RS-485 converter
Step1
Step2
Install the Software
Before utilizing the TSM11 Integrated Motor and Step-Servo Quick Tuner Software in an application, the following
steps are necessary:
a) Install the Step-Servo Quick Tuner
b) Launch the software by clicking Start Step-Servo Quick Tuner software...Programs...MOONS’.
c) ConnectthedrivetothePCusingRS-422/485,itisrecommendedtosetupina4-Wireconguration
(see “communication” below.)
Connect the Power Supply
a) Connect the power supply “+” terminal to the drive “+” terminal & the power
supply “-” terminal to the drive “-” terminal using AWG26 wire.
b) Be careful not to reverse the wires. Reversing the connection may open
the internal fuse and void the warranty.
c) If a regulated power supply is being used, there may be a problem
with regeneration that can be solved with the use of a MOONS’ RC880
Regeneration Clamp. Please see the MOONS’ website or the TSM11 User
Manual for more information.
d) Apply power to the drive.
e)
Thesoftwarewillrecognizethedriveanddisplaythemodelandrmware
version.
To Power Supply-
To Power Supply+
To Earth Ground
Safety Instructions
• Onlyqualiedpersonnelshouldassemble,
install, operate, or maintain this equipment.
• Read all available documentation before
assembly and operation.
• It is vital to ensure that all system components
are connected to earth ground.
• This product contains electrostatically
sensitive components that can be damaged
by incorrect handling.
Note: As with any integrated motor, the TSM11 must be mounted so as to provide maximum heat sinking and
airow.KeepenoughspacearoundtheIntegratedMotortoallowforairow.
CHINA/ 10TH/ AUGUST/ 2015

Step3
Congure the Drive
a) Apply power to the drive
b) The software will recognize the drive & display the model
&rmwareversion
c) Setup drive control mode, and control mode settings
d) Setup I/O settings
Moons' Industries (Europe) s.r.l.
Via Torri Bianche 1, 20871 Vimercate (MB), Italy
Web: www.moonsindustries.eu
E-mail: [e-mail]
TSM11 Quick Setup Guide
Communications
Four-Wire Configuration
RS-232 to RS-422/485 4-wire Converter
• UT-202 is a recommended ‘RS-232 to RS-422’ converter
fromUTEKTECHNOLOGY(SHENZHEN)CO,LTD.
It only supports to establish the full-duplex (4-wire)
RS-422 network.
The connection is as follows：
DB9 Male (PIN) Converter Output Drive
1 T/R+ RX+
2 T/R- RX-
3 RX+ TX+
4 RX- TX-
5 GND GND
USB to RS-422/485 4-wire Converter
• UT-890 is a recommended ‘USB to RS-422/485’ converter
fromUTEKTECHNOLOGY(SHENZHEN)CO,LTD.
It supports to establish either the half-duplex (2-wire)
RS-485 network or the full-duplex (4-wire) RS-422 network.
The connection is as follows：
DB9 Male (PIN) Converter Output Drive
1 T/R+ RX+
2 T/R- RX-
3 RX+ TX+
4 RX- TX-
5 GND GND
Two-Wire Configuration
RS-232 to RS-422/485 2-wire Converter
• UT-201 is a recommended ‘RS-232 to RS-485’ converter
fromUTEKTECHNOLOGY(SHENZHEN)CO,LTD.
It only supports to establish the half-duplex (2-wire) RS-
485 network.
The connection is as follows：
DB9 Male (PIN) Converter Output Drive
1 T/R+ RX+
2 T/R- RX-
3 T/R+ TX+
4 T/R- TX-
5 GND GND
USB to RS-422/485 2-wire Converters
• UT-890 is a recommended ‘USB to RS-422/485’ converter
from
UTEKTECHNOLOGY(SHENZHEN)CO,LTD.
It supports to establish either the half-duplex (2-wire) RS-
485 network or the full-duplex (4-wire) RS-422 network.
The connection is as follows：
DB9 Male (PIN) Converter Output Drive
1T/R+ RX+
2T/R- RX-
3T/R+ TX+
4T/R- TX-
5 GND GND
(http://www.szutek.cn)
a
c
b
d
If you have any questions or comments, please call MOONS' Customer Support:
[phone], or visit us online at www.moonsindustries.com.
CHINA/ 10TH/ AUGUST/ 2015