Morrell SW-UNM-16FE User manual

SW-UNM-16FE
16-Port 10/100Mbps Unmanaged Ethernet
Switch
User Manual
Version1.1 | 2015/8/13

1
Table of Contents
Chapter 1 Product Introduction .................................................................................................... 3
1.1 Product Overview ............................................................................................................... 3
1.2 Features ............................................................................................................................... 3
1.3 Package Contents ................................................................................................................ 3
Chapter 2 External Component Description ................................................................................ 4
2.1 Front Panel .......................................................................................................................... 4
2.2 Rear Panel ........................................................................................................................... 5
Chapter 3 Installing and Connecting the Switch .......................................................................... 7
3.1 Installation ........................................................................................................................... 7
3.1.1 Desktop Installation ................................................................................................. 7
3.1.2 Rack-mountable Installation in 19-inch Cabinet ...................................................... 8
3.1.3 Power on the Switch ................................................................................................. 8
3.2 Connect Computer (NIC) to the Switch .............................................................................. 9

2

3
Chapter 1 Product Introduction
Congratulations on your purchasing of the 16 port 10/100Mbps Fast Ethernet Switch.
Before you install and use this product, please read this manual carefully for full exploiting
the functions of this product.
1.1 Product Overview
The 10/100Mbps switch is the perfect way of integrating 10Mbps Ethernet and 100Mbps
Fast Ethernet devices. All sixteen ports are auto speed negotiating, and have automatic
MDI/MDI-X crossover detection, so you don't have to worry about the cable type. Each port
independently negotiates for best speed and half- or full-duplex mode. To increase the
functionality of your network, you can also add other Ethernet-enabled devices such as a
print server, Network-Attached Storage (NAS), and Internet camera.
1.2 Features
Sixteen 10/100BASE-T Ethernet Ports
Support Auto-Negotiation for 10/100Mbps and duplex mode
Support Auto-MDI/MDIX for each port
Support Full/Half duplex transfer mode for 10/100Mbps
Support Store-and-Forward switching method
Complies with IEEE 802.3,IEEE 802.3u
Support Wire-speed and non-blocking performance
3.2 Gbps Switching Capacity
Support Broadcast and multicast storm control
Supports MAC address auto-learning and auto-aging
4K MAC address table
1.3 Package Contents
 One 16 port 10/100Mbps Unmanaged Ethernet Switch
 A set of installation components
 One AC power cord
 One User Manual

4
Chapter 2 External Component Description
2.1 Front Panel
The front panel of the Switch consists of 16 x 10/100Mbps RJ-45 ports and a series of
LED indicators as shown as below.
Figure 1 - Front Panel
10/100Mbps RJ-45 ports (1~16):
Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps. Each has a
corresponding 10/100Mbps LED.
LED indicators:
The LED Indicators will allow you to monitor,diagnose and troubleshoot any potential
problem with the Switch,connection or attached devices.
Figure 2 - LED Indicators
The following chart shows the LED indicators of the Switch along with explanation of each
indicator.
LED COLOR STATUS STATUS DESCRIPTION
Power green On Power On

5
Off Power Off
LINK/ACT
(1~16)
10/100Mbps:
green
On A device is connected to the port
Off A device is disconnected to the port
Flashing Sending or receiving data
2.2 Rear Panel
The rear panel of the Switch contains AC power connector and one marker shown as
below.
Figure 3 - Rear Panel
AC Power Connector:
Power is supplied through an external AC power adapter.It s
upports AC 100~240V,
50~60Hz,0.3A.

6

7
Chapter 3 Installing and Connecting the Switch
This part describes how to install your Unmanaged Ethernet Switch and make connections
to it. Please read the following topics and perform the procedures in the order being
presented.
3.1 Installation
Please follow the following instructions in avoid of incorrect installation causing device
damage and security threat.
 Put the Switch on stable place or desktop in case of falling damage.
 Make sure the Switch works in the proper AC input range and matches the voltage
labeled on the Switch.
 To keep the Switch free from lightning, do not open the Switch’s shell even in power
failure.
 Make sure that there is proper heat dissipation from and adequate ventilation around
the Switch.
 Make sure the cabinet to enough back up the weight of the Switch and its accessories.
3.1.1 Desktop Installation
Sometimes users are not equipped with the 19-inch standard cabinet. So when installing
the Switch on a desktop, please attach these cushioning rubber feet provided on the
bottom at each corner of the Switch in case of the external vibration. Allow adequate space
for ventilation between the device and the objects around it.
Figure 4 - Desktop Installation

8
3.1.2 Rack-mountable Installation in 19-inch Cabinet
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed
in a wiring closet with other equipment. To install the Switch, please follow these steps:
a. attach the mounting brackets on the Switch’s side panels (one on each side) and
secure them with the screws provided.
Figure 5 - Bracket Installation
b. use the screws provided with the equipment rack to mount the Switch on the rack
and tighten it.
Figure 6 - Rack Installation
3.1.3 Power on the Switch
The Switch is powered on by the AC 100-240V 50/60Hz internal high-performance power
supply. Please follow the next tips to connect:
AC Electrical Outlet:
It is recommended to use single-phase three-wire receptacle with neutral outlet or
multifunctional computer professional receptacle. Please make sure to connect the metal

9
ground connector to the grounding source on the outlet.
AC Power Cord Connection:
Connect the AC power connector in the back panel of the Switch to external receptacle
with the included power cord, and check the power indicator is ON or not. When it is ON,
it indicates the power connection is OK.
3.2 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network card driver, please connect
one end of the twisted pair to RJ-45 jack of your computer, the other end will be connected
to any RJ-45 port of the Switch, the distance between Switch and computer is around 100
meters. Once the connection is OK and the devices are power on normally, the LINK/ACT
status indicator lights corresponding ports of the Switch.