Planet GSD-804P User manual

8-Port 10/100/1000Mbps with 4-Port PoE
Gigabit Ethernet Switch
GSD-804P
User's Manual

Trademarks
Copyright © PLANET Technology Corp. 2011.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks
belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does not
represent a commitment on the part of PLANET. PLANET assumes no responsibility
for any inaccuracies that may be contained in this User’s Manual. PLANET makes
no commitment to update or keep current the information in this User’s Manual,
and reserves the right to make improvements to this User’s Manual and/or to the
products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from
the power circuit.
Without removing power cable, the device will still consuming power from the
power source. In the view of Saving the Energy and reduce the unnecessary power
consuming, it is strongly suggested to remove the power connection for the device
if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste and have to collect such WEEE
separately.
Revision
PLANET 8-Port 10/100/1000Mbps with 4-Port PoE Gigabit Ethernet Switch User's
Manual For Model: GSD-804P
Revision: 1.0 (May 2011)
Part No.: 2350-A35100-000

Table of Contents
1. Introduction ............................................................................................... 5
1.1 Checklist............................................................................................. 5
1.2 Product Description.............................................................................. 5
1.3 Features ............................................................................................. 5
1.4 Specication........................................................................................ 7
2. Hardware Description .................................................................................. 8
2.1 Front Panel........................................................................................... 8
2.1.1 LED Indicators ............................................................................ 9
2.2 Rear Panel ........................................................................................... 9
3. Hardware Installation .................................................................................10
3.2 Rack Mounting ...................................................................................12
3.3 Product Application............................................................................13
3.3.1 Connecting end node or Switch ..................................................13
3.3.2 Department/ Workgroup PoE Switch............................................14
3.4 Power over Ethernet Powered Device ..................................................15
4. Power over Ethernet Overview...................................................................16
5. Troubleshooting .........................................................................................19
Appendix A Networking Connection ..................................................................20
A.1 Data Out PoE Switch RJ-45 Port Pin Assignments (Port 1 to Port-4)........20
A.2 Switch's RJ-45 Pin Assignments - 1000Mbps, 1000Base-T ......................20
A.3 Switch's RJ-45 Pin Assignments - 10/100Mbps, 10/100Base-TX ..............21

1. Introduction
1.1 Checklist
Check the contents of your package for following parts:
GSD-804P x 1
User's Manual x 1
Power Cord x 1
If any of these pieces are missing or damaged, please contact your dealer
immediately, if possible, retain the carton including the original packing material,
and use them against to repack the product in case there is a need to return it to
us for repair.
1.2 Product Description
To fulll the demand of sufcient PoE power for network applications with Gigabit
speed transmission, the new member in the 802.3af PoE Gigabit Ethernet Switch
family - GSD-804P, the 8-Port 10/100/1000Mbps with 4-Port 802.3af Power over
Ethernet Switch which features high performance Gigabit IEEE 802.3af PoE (Up to
15.4 Watts) and totally 55 Watts PoE budget on half of the 10/100/1000Mbps TP
ports of GSD-804P. The four 802.3af PoE ports provide PoE power injector function
which is able to drive 4 IEEE 802.3af compliant powered devices. The GSD-804P
also provides a simple, cost-effective, and non-blocking wire-speed performance
with 10-inch metal shape for desktop deployment in compact housing, SOHO ofce
or department network application.
All RJ-45 copper interfaces in the GSD-804P support 10/100/1000Mbps Auto-
Negotiation for optimal speed detection through RJ-45 Category 6, 5 or 5e cables.
It also supports standard Auto-MDI/MDI-X that can detect the type of connection
to any Ethernet device without requiring special straight or crossover cables.
1.3 Features
RJ-45 Interface
8-Port 10/100/1000Mbps Gigabit Ethernet portsl
4-Port supports 48V DC power to PoE Powered Devicel
PoE
Complies with IEEE 802.3af Power over Ethernet End-Span PSEl
Up to 4 IEEE 802.3af devices poweredl

6
Supports PoE Power up to 15.4 Watts for each PoE portl
Auto detect powered device (PD)l
Circuit protection prevents power interference between portsl
Remote power feeding up to 100ml
Switching
Hardware based 10/100/1000Mbps Auto-Negotiation and Auto MDI/MDI-Xl
Flow control for Full Duplex operation and back pressure for Half Duplex oper-l
ation
Integrates address look-up engine, supporting 8K absolute MAC addressesl
9K Jumbo Frame supports at all speed (10/100/1000Mbps)l
Automatic address learning and address agingl
Hardware
10-inch desktop size, rack mountable; 1U heightl
LED indicators for PoE ready and PoE activityl
Optional Rack Ear Accessories Kit for 10-inch cabinet (RKE-10A) and 19-inchl
cabinet (RKE-10B)
1 silent FAN to provide stable and efcient power performancel
Energy-Saving technologyl
Link down power saving
Intelligent scales power based on cable length

7
1.4 Specication
Model GSD-804P
Hardware Specication
Network Connector 8-Port RJ-45 for 10/100/1000Base-T
PoE Inject Port 4-Port with 802.3af PoE injector function, Port-1 to
Port-4
LED Display
1 Power, 1 FAN Alert LED
1-4 port PoE in-use
1-8 port Speed, LNK/ACT
Switch Architecture Store and Forward switch architecture
MAC Address 8K MAC address table with Auto learning function
Switch Fabric 16Gbps
Switch Throughput 11.9Mpps
Jumbo Packet Size 9K Bytes
Power Requirement AC 100~240V, 50/60Hz, 1.5A
Power Consumption Max. 65 Watts / 221 BTU
Dimension (W x D x H) 217 x 135 x 43 mm
Weight 890g
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PSE
PoE Power Supply Type End-Span
PoE Power Output Per Port 48V DC, 350mA . Max. 15.4 Watts
Power Pin Assignment 1/2(+), 3/6(-)
PoE Power Budget 55 Watts
Standard Conformance
EMI Safety FCC Class A, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3ab
IEEE 802.3x
IEEE 802.3af
Ethernet
Fast Ethernet
Gigabit Ethernet
Flow Control
Power over Ethernet
Environment
Operating Environment 0 ~ 50 Degree C
Storage Environment -40 ~ 70 Degree C
Operating Humidity 5 ~ 95%, relative humidity, non-condensing
Storage Humidity 5 ~ 95%, relative humidity, non-condensing

8
2. Hardware Description
This product provides three different running speeds – 10Mbps, 100Mbps and
1000Mbps in the same switch and automatically distinguishes the speed of
incoming connection.
This section describes the hardware features of GSD-804P. For easier management
and control of the Switch, familiarize yourself with its display indicators, and ports.
Front panel illustrations in this chapter display the unit LED indicators. Before
connecting any network device to the GSD-804P, please read this chapter carefully.
In the following section, the term “Switch” means the Switch device, ie. GSD-
804P; term of “switch” can be any third switches.
2.1 Front Panel
The Front Panel of the GSD-804P PoE Ethernet Switch consists of 8x Auto-Sensing
10/100/1000Mbps Ethernet RJ-45 Ports. The LED Indicators are also located on the
front panel of the GSD-804P.
Figure 2-1: GSD-804P Switch Front Panel

9
2.1.1 LED Indicators
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
FAN Alert Orange Lights to indicate that the FAN failure.
Per 10/100/1000Mbps Port
LED Color Function
PoE In-use Orange Lights to indicate the port is providing 48V DC in-line
power. (1-4 ports)
Speed Green
Lit: indicate the Switch is successfully connecting to the
network at 1000Mbps.
Off: indicate that the Switch is successfully connecting
to the network at 10Mbps or 100Mbps.
LNK/ACT Green
Lit: indicate the link through that port is successfully
established.
Blinks to indicate that the Switch is actively sending or
receiving data over that port.
2.2 Rear Panel
The rear panel of the GSD-804P indicates an AC inlet power socket, which accepts
input power from 100 to 240VAC, 50-60Hz. And have a fan hole on the rear panel.
Figure 2-2: GSD-804P Switch Rear Panel
Power
Notice
1. The device is a power-required device, it means, it will not work
till it is powered. If your networks should active all the time,
please consider using UPS (Uninterrupted Power Supply) for your
device. It will prevent you from network data loss or network
downtime.
2. In some area, installing a surge suppression device may also
help to protect your GSD-804P from being damaged by unregu-
lated surge or current to the GSD-804P or the power adapter.

10
3. Hardware Installation
Before start up
Before your installation, please refer to the followings for your cabling:
10/100/1000Base-T
All 10/100/1000Base-T ports come with Auto-Negotiation capability. They
automatically support 1000Base-T, 100Base-TX and 10Base-T networks. Users
only need to plug a working network device into one of the 10/100/1000Base-T
ports, and then turn on the GSD-804P. The port will automatically runs in 10Mbps,
20Mbps, 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after the negotiation
with the connected device.
Cabling
Each 10/100/1000Base-T ports use RJ-45 sockets - similar to phone jacks - for
connection of unshielded twisted-pair cable (UTP). The IEEE 802.3 / 802.3u
802.3ab Fast / Gigabit Ethernet standard requires Category 5 UTP for 100Mbps
100Base-TX. 10Base-T networks can use Cat.3, 4, 5 or 1000Base-T use 5/5e/6 UTP
(see table below). Maximum distance is 100meters (328 feet).
Port Type Cable Type Connector
10Base-T Cat 3, 4, 5, 2-pair RJ-45
100Base-TX Cat.5 UTP, 2-pair RJ-45
1000Base-T Cat.5/5e/6 UTP, 2-pair RJ-45
Any Ethernet devices like hubs/ PCs can connect to the GSD-804P by using
straight-through wires. The eight-10/100/1000Mbps ports are auto-MDI/MDI-X can
be used on straight-through or crossover cable.