Planet GSD-800S User manual

Trademarks
Copyright  PLANET Technology Corp. 2005.
Contents subject to which revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trade-
marks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representa-
tion, either implied or expressed, with respect to the quality, performance,
merchantability, or tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does
not represent a commitment on the part of PLANET. PLANET assumes no re-
sponsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information
in this User’s Manual, and reserves the right to make improvements to this
User’s Manual and/or to the products described in this User’s Manual, at any
time without notice.
If you nd information in this manual that is incorrect, misleading, or incom-
plete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at whose own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.

WEEE Warning
To avoid the potential effects on the environment and human health
as a result of the presence of hazardous substances in electrical and
electronic equipment, end users of electrical and electronic equipment
should understand the meaning of the crossed-out wheeled bin symbol.
Do not dispose of WEEE as unsorted municipal waste and have to col-
lect such WEEE separately.
Revision
PLANET Gigabit Ethernet Switch User’s Manual
FOR MODEL: GSD-800S
Rev: 2.0
Part No. 2010-A35040-000

Table of Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 How to Use This Manual 1
1.3 Product Features 2
1.4 Product Specifications 3
Chapter 2 Installation 5
2.1 Product Description 5
2.2 Installing a 800S 6
Chapter 3 Configuration 8
3.1 Preparing for configuration 8
3.2 General 9
3.3 Commands 12
3.4 Examples 23
Chapter 4 Web Interface 25
4.1 Starting the Web Interface 25
Chapter 5 Troubleshooting 26
5.2 Address Table 26
5.2 Learning 26
5.3 Forwarding & Filtering 26
5.4 Store-and-Forward 26
5.5 Auto-Negotiation 27
Chapter 6 Trouble Shooting 28
APPENDIX A 29
A.1 Switch‘s RJ-45 Pin Assignments 29
A.2 10/100Mbps, 10/100Base-TX 29

1

1
Chapter 1
INTRODUCTION
1.1 Package Contents
Open the box of the Switch and unpack it carefully. The box should contain the following
items:
● The Switch
● Power Cord x 1
● RS-232 Cable x 1
● User s Manual x 1
If any item is found missing or damaged, please contact your local reseller for replacement.
Please retain the carton including the original packing material, and use them against to
repack the product in case there is a need to return it to us for repair.
1.2 How to Use This Manual
This Gigabit Ethernet Switch User Manual is structured as follows:
Chapter 2 Installation
This chapter explains the functions and how to physically install the GSD-800S.
Chapter 3 Conguration
This chapter contains information about the smart function of GSD-800S.
Chapter 4 Web Interface
This chapter contains troubleshooting and specications of GSD-800S
Chapter 5 Switch Operation
This chapter explains the switch operation of GSD-800S.
Chapter 6 Trouble Shooting
This chapter contains troubleshooting of GSD-800S
Appendices
This chapter contains cable information of GSD-800S.

2
3
1.3 Product Features
● Complies with IEEE802.3, 10Base-T, IEEE802.3u, 100Base-TX and
IEEE802.3ab, 1000Base-T
● IEEE802.3x, full-duplex flow control compliant; back-pressure, half-duplex
flow control
● 10/100/1000Mbps 8-port Ethernet / Smart Switch (RJ-45)
● 144 bytes packet buffer and 8K MAC address table, auto-ageing.
● Per port Auto-MDI, MDI-X detection
● Store and Forward switching architecture
● Non-blocking switch fabric
● Automatic source address learning and aging
● RS-232 console interface for console program management of smart feature
● Port trunking support to optionally increase bandwidth between switches
● VLAN support with up to 8 VLAN groups
● 4 Classes of Service selectable on a per port basis and/or checked by IP ToS
header
● Support Port mirroring for port traffic diagnosis with sniffer programs
● 10”, 1U height rack mounting size
● 100~240VAC, 50~60Hz universal power input

2
3
1.4 Product Specications
Model GSD-800S
Hardware Specification
Network ports 8 10/100/1000Base-T RJ-45 MDI/MDI-X ports
Console port 1 RS-232 DB-9 male
Dimensions 217 x 135 x 43.5 mm (1U height)
Weight 1.1 kg
Power Requirement 100~240 (±10%) VAC, 50-60 (±3) Hz
Power Consumption 21 Watts maximum / 71 BTU/hr maximum
Switch Specification
Switch architecture Store-and-forward
Address Table 8K entries, auto learning/ageing
Flow Control Back pressure for half duplex, IEEE 802.3x for full
duplex
Packet Control Runt & CRC filtering, Broadcast storm control
Switching Fabric 16Gbps
Switch Management
Port Config Configure each port’s speed, duplex mode, flow
control and priority
Port Status Show each port’s link status and speed, duplex
mode
VLAN Up to 8 VLAN groups
Port Trunking 2 port trunk support
Port Mirroring Mirroring port’s in/out traffic
Traffic Prioritization 4 Classes of Service selectable on a per port basis
and / or checked by IP ToS header
Standards Conformance
Network Standards IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab
IEEE8023x (flow control)
Operating Temperature 0~50˚C
Storage Temperature -40~70˚C

4
5
Humidity 10% to 90% (Non-condensing)
Regulation Compliance FCC, CE

4
5
Chapter 2
INSTALLATION
TThis section describes the functionalities of GSD-800S’s components and guides how to
install it on the desktop or shelf. Basic knowledge of networking is assumed. Please read
this chapter completely before continuing.
2.1 Product Description
The PLANET GSD-800S provides 8 Gigabit Ethernet Switch ports. The PLANET GSD-800S
delivers eight ports worth of high-performance, feature-rich integrated Gigabit Ethernet
switching over traditional copper cabling. The GSD-800S is capable of smart functions,
such as VLAN, Port trunking and Prot mirroring. GSD-800S can be congured by out-of-
band channel via the console port (RS232) directly. Each port supports 10Mbps, 100Mbps,
and 1000Mbps as well as half/full mode and can be easily connected to corporate
backbones and servers.
2.1.1 Product Overview
PLANET GSD-800S is a gigabit Ethernet switch with 8 RJ-45 10/100/1000 Mbps ports
for high-speed network connectivity. GSD-800S can also automatically identify and
determine the correct transmission speed and half/full duplex mode of the attached
devices with its 8 ports. The Gigabit port can handle large amounts of data transmission
in a secure topology linking to a backbone or high-power servers.
This product also supports store-and-forward forwarding scheme to ensure low latency
and high data integrity, eliminates unnecessary trafc and relieves congestion on critical
network paths. With an intelligent address recognition algorithm, GSD-800S could
recognize up to 8K different MAC address and enables ltering and forwarding at full
wire speed.
2.1.2 GSD-800S Front Panel
Figure 2-1 shows the front panel of GSD-800S
2.1.3 LED Indicators
LED Color Function
PWR Green Light: Power on
1000 Green Light: The port is operation at 1000Mbps speed
100 Green Light: The port is operation at 100Mbps speed
10 Green Light: The port is operation at 10Mbps speed

6
7
2.1.4 GSD-800S rear panel
The rear panel of the Switch indicates an AC inlet power socket, which accepts input
power from 100 to 240VAC, 50-60Hz.
Figure 2-2 Rear Panel of GSD-800S
Power Notice:
1. The device is a power-required device, it means, it will not work till it is pow-
ered. If your networks should active all the time, please consider using UPS
(Uninterrupted Power Supply) for your device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppression device may also help to protect
your switch from being damaged by unregulated surge or current to the Switch
or the power adapter.
2.2 Installing a GSD-800S
This part describes how to install your GSD-800S Gigabit Ethernet Switch and make
connections to the switch. Please read the following topics and perform the procedures in
the order being presented.
PLANET GSD-800S Gigabit Ethernet Switch do not need software conguration. To install
your GSD-800S on a desktop or shelf, simply complete the following steps.
2.2.1 Desktop Installation
To install a GSD-800S on a desktop or shelf, simply complete the following steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the switch.
Step2: Place the GSD-800S on a desktop or shelf near an AC power source.
 NOTE:
Optional rack-ear for 10-inch cabinet rack mounting (RKE-10A)
and 19-inch cabinet rack mounting (RKE-10B) is available upon
request.
Step3: Keep enough ventilation space between the switch and the surrounding objects
 NOTE:
When choosing a location, please keep in mind the environ-
mental restrictions discussed in Chapter 1, Section 4, Product
Specication.
Step4: Connect your GSD-800S to network devices