Mosquito Magnet LibertyPlus User manual

LibertyPlus
Your trap will begin working immediately. See noticeable
results in as little as 7 – 10 days, but allow 4 – 6 weeks
to significantly reduce the mosquito population in your yard.
For Outdoor Use Only
Operation Manual
Cordless
American Biophysics Corporation
140 Frenchtown Rd.
North Kingstown, RI 02852
1-877-699-8727
www.mosquitomagnet.com
Patents:
US Patents: No. 6,145,243, No. 6,286,249
Canadian Patents: No. 2,265,944, No. 2.322,038
European Patents No. 1,011,324
Other patents pending
Made in the USA
1440-604 Rev. A

2
For accessories and additional info go to: www.mosquitomagnet.com
1
American Biophysics 1-877-699-8727
Safety Instructions
Please read and follow all safety
instructions and warnings.
For your safety if you smell gas:
1. Shut off the gas to your Liberty Plus.
2. Extinguish any open flame.
3. If odor continues, immediately call
your gas supplier.
4. Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
5. The Liberty Plus is for outdoor use
only. If stored indoors detach and
leave propane cylinder outdoors
at all times.
Note: Some or all of the following required safety
instructions for propane powered devices may apply
to your Liberty Plus.
Warning: Improper installation, adjustment,
alteration, service or maintenance can cause injury or
property damage. Read the installation, operating and
maintenance instructions thoroughly before installing
or servicing the Liberty Plus.
Caution: The gas pressure regulator provided with this
appliance must be used. This regulator is set for an outlet
pressure of 11.0 in. Water Column. The minimum inlet gas
supply pressure is 11” WC from regulator.
•The gas supply must be turned off at the LP-Gas supply cylinder
when this appliance is not in use.
•The installation must conform with local codes or, in the absence
of local codes, with the National Fuel Gas Code, ANSI Z223.
1-1998 for US and with the CAN1-B149 for Canada.
•To test for a gas leak, place soapy water around the regulator.
If bubbles appear, there is a gas leak.
•The hose assembly must be replaced prior to the appliance being
put into operation if there is evidence of excessive abrasion or
wear, or if the hose is damaged. The instructions shall state that
the replacement hose assembly shall be that specified by the
manufacturer.
•The Liberty Plus is equipped with an internal hot surface ignition
device. Failure to follow starting procedure will result in the trap
not starting.
•Installation and repair should be done by a qualified service person.
The heater should be inspected before use and at least annually by
a qualified service person. More frequent cleaning may be required
as necessary. It is imperative that the control compartment,
burners, and circulating air passageways of the heater be kept
clean.
•Adequate clearances of 20” – 24” around air openings into the
combustion chamber, clearances from combustible material,
provisions for accessibility and for combustion and ventilating
air supply. Keep the Liberty Plus area clear and free from
combustible materials, gasoline, and other flammable vapors
and liquids. The appliance is not to be used in locations where
flammable vapor or explosive dust is likely to exist.
•Do not obstruct the flow of combustion and ventilation air.
•Keep the ventilating openings of the cylinder enclosure
free and clear from debris.
•Clean the Liberty Plus with a water damp cloth, if necessary.
•A maximum of a 20 lb. LP-Gas cylinder shall be used.
Model No.: Liberty Plus
Serial No.:
Type of Gas: Propane
Manifold Pressure: 100 – 110 psi
Minimum Gas Supply Pressure: 11.0 in. WC
Input Rating: 650 Btu/Hr.
Minimum Clearances: 20 – 24”
Contents
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Principle Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Additional Components . . . . . . . . . . . . . . . . . . . . . . . . . .4
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
Charging trap
Trap Placement
Propane Tank Installation
Tank Changing Tips
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Starting Instructions
Shut-Down Instructions
For Best Results
Quick Clear Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
LED Fault Codes
Gas Reset Tool
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
How the Mosquito Magnet®Works
Mosquitoes and other biting insects use the long-range
attractant carbon dioxide (CO2) to locate people. Once in close
proximity, mosquitoes use short-range attractants such as
scents emitted from the skin, to determine which person they
are going to bite. The Mosquito Magnet®mimics a human
by converting propane to CO2, with its patented catalytic
conversion technology, in combination with a short-range
attractant (patent pending).
Attracted by the CO2and short-range attractant, mosquitoes
and other biting insects are drawn to the Mosquito Magnet®.
When they reach the trap, the insects are vacuumed into
a net by our patented Counterflow Technology™, where they
dehydrate and die within 24 hours.
The Mosquito Magnet®is silent and odorless. When properly
placed in your yard, the trap begins working immediately.
Noticeable results can be achieved in 7 to 10 days. To greatly
reduce your biting insect population, allow 4 – 6 weeks. Leave
the Mosquito Magnet®out all summer long, to control the
mosquito population in your yard.
Only biting insects are targeted including mosquitoes,
no-see-ums, black flies and biting midges, not beneficial
insects such as butterflies, bees or moths.
Questions or Comments
Please contact American Biophysics®Corporation if you
have any questions or experience any problems with your
Mosquito Magnet: 1-877-699-8727
American Biophysics Corporation
140 Frenchtown Rd.
North Kingstown, RI 02852
P: 401-884-3500
F: 401-884-6688
www.mosquitomagnet.com
Counterflow TechnologyTM
Children and adults should be
alerted to the hazards of high surface
temperatures and should stay away
to avoid burns or clothing ignition.
Young children should be carefully
supervised when they are in the
area of the heater. Keep out of reach
of children.
Clothing or other flammable materials
should not be hung from the heater,
or placed on or near the heater.

4
For accessories and additional info go to: www.mosquitomagnet.com
3
American Biophysics 1-877-699-8727
Principle Parts
Parts Included
Safety Instructions
•The LP-Gas cylinder must be provided with a shut-off valve
terminating in an LP-Gas supply cylinder valve outlet specified for
Connection No. 510 in the Standard for Compressed Gas Cylinder
Valve Outlet and Inlet Connections, ANSI/CGA-V-1-1977.
•The LP-Gas cylinder supply system must be arranged for vapor
withdrawal and the cylinder must include a collar to protect the
cylinder valve.
•The LP-Gas cylinder used shall be constructed and marked in
accordance with the specifications for LA-Gas cylinders of the
U.S. Department of Transportation (DOT).
•The Liberty Plus shall be used outdoors only in a well ventilated
space and shall not be used in a building, garage,
or any other enclosed area.
•The LP-Gas cylinder must be disconnected and removed from
the appliance, if the appliance is stored indoors.
•LP-Gas cylinders must be stored outdoors in a well-ventilated
area out of reach of children.
•Disconnected cylinders must have threaded valve plugs tightly
installed and must not be stored in a building, garage, or any
other enclosed area.
•The pressure regulator and hose assembly supplied with this
appliance must be used for connection to the LP-Gas cylinder.
Replacement pressure regulators and hose assemblies must
be specified by the manufacturer.
•Avoid improper use of extension cords. Keep connections away
from moisture and avoid damage to the cord.
•If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person
in order to avoid hazard.
Please contact Customer Service if you have any questions at:
1-877-699-8727
Self-Contained
Liberty Plus
Head Unit (1)
Support Pole (1)
Base Support (1)
Regulator Hose (1)
Charging Adapter Net Mosquito Magnet®Octenol
Biting Insect Attractant
EPA Reg. No. 72563-1
(Short-Range Attractant)
Gas Reset Tool Plume Tube Re-Chargeable Battery
Quick Clear Adapter

Trap Assembly:
6
For accessories and additional info go to: www.mosquitomagnet.com
Charging your Mosquito Magnet®Liberty Plus
1. Remove cover panel from rear of Head Unit (panel snaps off).
2. Insert and connect re-chargeable battery.
3. Insert Charging Adapter into rear of Head Unit.
Allow to charge for 24 hours at the beginning of each
season. You will not need to charge again until next season.
Replace cover panel when completed (panel snaps into place).
NOTE: Unit must be charged indoors, trap is not
weatherproof with cover panel removed.
Attractant Installation:
See Mosquito Magnet®attractant label for installation,
use, storage and disposal instructions.
Trap Placement
1. Determine the direction of the prevailing wind.
Check local weather patterns if you are unsure
2. Stand in the center of the area you are trying to protect
and look toward the prevailing wind.
3. Proper placement of the Liberty Plus will be 30 – 40 feet
in front of you, within 5-6 feet of ground cover (i.e., bushes,
flowerbeds, tree line, marshbed). Ensure that trap is not
directly against any blockades such as buildings, fences, etc.
4. It is recommended that the trap be placed in the shade.
5. Do not place trap directly above a water source
(sprinklers, hose, etc.).
7. Trap must be placed on level ground to avoid tipping
or uneven propane distribution.
8. For more information, refer to trap placement CD-ROM
included with your Liberty Plus.
Installation
5
American Biophysics 1-877-699-8727
3
Assembly Instructions
Step 1
Step 2
Step 3
Net locks into front of compartment
Step 4
See Attractant Package for details.
Horn
Remove Back Panel
Insert & Connect Battery
Plug Charger Into Battery Charging Powerhead
For optimal trap placement
in your yard, refer to trap
placement CD-ROM included
with your Liberty Plus.
Step 5
Charge Liberty Plus for 24 hours before use.
See pg. 6 for further details.
NOTE: You will not need to charge it again until the
following season.
Net Installation:
Lift clear plastic lid and lock plastic holding bracket of net into
front of compartment. Close plastic lid when finished.
Note: Fabric loops hook over plastic posts allowing net
to expand to it highest capacity.
Place base upside down on a flat surface, unfold U-shaped
support leg until it locks in place.
Insert the Plume Tube into horn and turn until Tube locks
into place.
Place Liberty Plus power head onto pole. Press down firmly
with two hands to secure.
Assembled trap should have the front of power head
in the same direction as base U-shaped legs.
Turn base and leg assembly right-side-up and place support
pole into cavity on base.

8
For accessories and additional info go to: www.mosquitomagnet.com
Shut Down
Starting Instructions
It is recommended that you read the entire manual before
starting the Liberty Plus trap.
1. Connect regulator to propane tank.
2. Slowly open propane tank valve.
3. Push ON/OFF switch to ON position.
LED light will turn solid orange indicating warm-up.
After 15 to 25 min. trap LED light will turn solid green
indicating the trap is running at full capacity.
Shut Down Instructions
Push ON/OFF switch to OFF position to shut down the Liberty
Plus. The LED light will go out and the fan will continue
running until trap is cool. Close the propane tank valve and
disconnect regulator.
Any open Mosquito Magnet®attractant should be removed
and discarded. See attractant label for disposal instructions.
The net should also be discarded prior to storing the
Liberty Plus.
STORAGE: Liberty Plus should be stored indoors in the
off-season. Cover unit with trap cover available at
www.mosquitomagnet.com or with a tarp and secure tightly
at the bottom to keep out dust, spider webs and other debris.
NOTE: It is recommended that you use the Quick Clear valve
before seasonal storage to avoid build-up of contaminants
during off-season (see page 9).
Maintenance
• 21 Day Maintenance Cycle
- Refill propane. (propane lasts approximately 21 days with
24-hour operation)
- Use gas Reset Tool before connecting newly filled propane
tank to the regulator. (see page 11)
- Replace short-range attractant cartridge.
See Mosquito Magnet®attractant label for instructions.
- Empty or replace net.
• Utilize the Quick Clear valve at first tank change and every
second tank change thereafter.
• Periodically wipe down the outside of the Liberty Plus
with a clean, water damp cloth.
• Charge your Mosquito Magnet®Liberty Plus for 24 hours
at the beginning of each season (see page 6).
Maintenance
7
American Biophysics 1-877-699-8727
ON/OFF Switch
Propane Tank Installation
1. After trap is placed in its ideal location, place propane
tank onto the molded cradle.
2. Making sure propane tank is fully closed, utilize
Gas Reset Tool (see page 11). Attach propane regulator
hose to propane tank. Secure tightly by hand.
Do not use tools.
3. Turn propane on by slowly turning valve counter-clockwise.
Take care not to turn too quickly to avoid engagement of
safety check valve regulator.
DO NOT MOVE TRAP WITH TANK ATTACHED!
TANK MUST BE DISCONNECTED FROM REGULATOR
BEFORE TRAP IS RELOCATED TO AVOID DAMAGE TO
REGULATOR AND/OR TRAP. BE ADVISED, DAMAGE
CAUSED FROM FAILURE TO COMPLY WITH THIS
INSTRUCTION IS NOT COVERED UNDER WARRANTY.
Propane Tank Changing Tips
When attaching the regulator handle to a tank after a tank
change, be sure to fully tighten the regulator handle onto the
tank. No need to use tools, but do turn the handle as far as
possible by hand. When this is done, loosen the handle 1/4 turn,
then re-tighten the handle. Frequently this action will result in
additional turns beyond the 1/4 turn.
The purpose for this is to fully engage the regulator onto the
tank. If the regulator is not fully engaged, the flow of gas may
be restricted to the point where the trap will show a gas empty
code. If this occurs, press the off button, close the tank valve,
and remove the regulator from the tank. Utilize Gas Reset Tool
(see page 11) then re-attach the regulator and try again.
Installation
Step 1 – Propane Tank Placement
Step 2 – Attach Regulator
Step 3 – Slowly Open Valve For Best Results
• Your trap will begin capturing immediately, but allow
4 – 6 weeks to significantly reduce the mosquito population
in your yard.
• Never spray insecticide in or around trap.
• Trap can be left running in the rain.
• If using lime or fertilizer compounds, be sure
to shut down the Liberty Plus first to prevent dust or fine
mist from being drawn into trap and clogging net.

10
For accessories and additional info go to: www.mosquitomagnet.com
Troubleshooting
Quick Clear Valve
Important: Extinguish all smoking materials prior
to use of Quick Clear Valve. Do not stand directly
behind the Quick Clear cartridge during operation.
Quick Clear is recommended for regular maintenance
to remove built-up contaminants but is not required for
operation of your Liberty Plus.
Recommended for use at first tank change, and every
second tank change thereafter. Also recommended for use
before seasonal storage to avoid build up of contaminants
during the off-season.
The Quick Clear valve is a gold, threaded knob located on the
back of your trap. It should be used with the adapter included
with your Liberty Plus, and a threaded Quick Clear cartridge
available on our website at: www.mosquitomagnet.com
or at your local Mosquito Magnet Dealer.
1. Shut down your Liberty Plus. Let fan run until it stops.
(About 35 mins)
2. Close the propane tank valve by turning to the “OFF”
position. (Turn the tank valve clockwise)
3. Remove the protective cap from Quick Clear valve
on your trap.
4. Hand-screw the Quick Clear adapter on to Quick Clear
valve, until finger tight.
5. Hand-screw the Quick Clear cartridge into the Quick Clear
adapter clockwise until hand tight while holding the
adapter in place.
Important: Do not over-tighten.
6. While holding the adapter in place
slowly unscrew
Quick Clear cartridge up to 1/4 turn only in counter clockwise
direction from the Quick Clear adapter only. The strong flow
of compressed air lasts approximately 3 minutes. Be sure
to allow Quick Clear cartridge to run out completely.
(Hissing will stop when cylinder is empty. Quick Clear
cartridge will be cold to the touch)
7. Unscrew the Quick Clear cartridge to remove. Discard empty
Quick Clear cartridge after use, it is not reusable or refillable.
8. Unscrew the Quick Clear adapter to remove.
Use caution when removing Quick Clear adapter and
cartridge, as some compressed air may come out at
this time.
Remember to keep the Quick Clear adapter for future use.
9. Replace Quick Clear valve protective cap, and proceed
with normal start up of your Liberty Plus. If use of
Quick Clear valve feature does not resolve starting trouble,
contact Customer Service 1-877-699-8727.
Quick Clear Valve
9
American Biophysics 1-877-699-8727
Step 4
Step 5
Step 6
Step 7
First hand-screw the Quick Clear adapter onto the valve.
While holding the adapter in place, screw the Quick Clear
cartridge into Quick Clear adapter.
To start cleaning process, while holding Quick Clear Adapter
in place, unscrew the Quick Clear cartridge 1/4 Turn Only.
Unscrew the Quick Clear cartridge first, then unscrew Quick
Clear adapter and discard the spent Quick Clear cartridge.
Remember to keep the Quick Clear adapter
Problem
Unit won’t start
LED flashing RED
Unit won’t stay running
Low or No Catch
LED Flashing alt RED/GREEN
LED Flashing alt RED/ORANGE
Possible Cause
1. Propane tank may be empty.
2. If propane tank is new and has been
newly filled it must be purged.
3. There could be a loose connection.
4. If tank has been opened too quickly,
security check valve may have been
triggered.
5. Fuel line maybe blocked by propane
contaminants.
1. ‘Possible Causes’ 1 & 3 above may apply.
2. Fuel line may be blocked by propane
contaminants.
3. Regulator is not fully engaged.
If not getting bitten
1. Insects may not be out yet.
If getting bitten
2. Trap placement issue.
3. Biting insect reproductive
cycles have not yet been broken.
4. Counterflow may be disrupted.
High Temp
Battery Voltage Low
Solutions
1. Weigh tank and check against “empty” weight
written on tank.
2. Bring tank to filling location. Air may be in
fuel line. Ask for tank to be purged.
Hint: If you have another propane powered device
operating on a standard, 20 lb propane tank, try
hooking that tank up to the Liberty Plus to verify
that the issue is with your tank.
3. Verify all connections. Make sure propane tank
valve is fully open.
4. Refer to Gas Reset Tool Instructions on page 11.
5. Use Quick Clear valve.
1. Go through above steps 1 & 3.
2. See Quick Clear valve instructions on page 9.
3. See Tank Changing Tips on page 7.
1. Verify temperature is consistently over 50°F (10°C).
2. Follow steps in the “Trap Placement” section
of your owner’s manual or refer to your trap
Placement CD included with your Liberty Plus.
3. Keep trap in constant operation 24 hours/day,
7 days per week for at least 4-6 weeks to reduce
the mosquito population.
4. Air flow may be restricted. Call Customer Service
at: 1-877-699-8727.
1. Turn off trap and allow to cool for 1/2 hour.
Then restart. If code continues, call Customer
Service at: 1-877-699-8727.
1. Make sure you have charged the battery for
24 hours before starting trap for the first time out
of the box, and the first time before each season.
2. Check all battery connections, make sure they
are fully inserted.
3. After several repeated unsuccessful attempts
to start your Mosquito Magnet®the battery may
need to be recharged.

12
For accessories and additional info go to: www.mosquitomagnet.com
11
Limited Warranty
This warranty, (1) year from the purchase of the unit, is
extended only to the original purchaser/user of products.
American Biophysics Corp. warrants its products to be free
from defects in materials and workmanship for the warranty
period by the original purchaser/user.
For warranty service, please contact American Biophysics’
Technical Center (877-699-8727). Please indicate the nature
of the defect.
If American Biophysics Corp. determines there may be a
defect, American Biophysics Corp. will issue a return
authorization (RMA) number. The defective unit or parts must
be returned for warranty inspection using the RMA number,
when applicable, as identification within (30) days of return
authorization date. DO NOT return products to our factory
without our prior consent, as they, as well as C.O.D. shipments
will be refused. American Biophysics Corp., at its option, shall
replace the unit, replace the defective part(s) and return such
unit to you. American Biophysics Corp.’s sole obligation and
your exclusive remedy under this warranty shall be limited to
such replacement.
LIMITATIONS AND EXCLUSIONS: The warranty shall not apply
to problems arising from normal wear, or failure to adhere to
the enclosed instructions. In addition, the foregoing warranty
shall not apply to serial numbered products if the serial
number has been removed or defaced; products subject to
negligence, accident, improper operation, maintenance or
storage; products damaged by circumstances beyond
American Biophysics Corp.’s control; or products modified
(including, but not limited to modifications through the use of
unauthorized parts or attachments) or repaired by anyone other
than American Biophysics Corp. or its designee.
Limited Warranty
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IT SHALL NOT EXTEND BEYOND THE DURATION OF
THE EXPRESS WARRANTY PROVIDED HEREIN, AND THE
REMEDY FOR VIOLATIONS OF ANY WARRANTY SHALL BE
LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE
PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN.
AMERICAN BIOPHYSICS CORP. SHALL NOT BE LIABLE FOR
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
WHATSOEVER.
This warranty gives you specific legal rights and you may also
have other legal rights which may vary based on location.
This warranty is valid only in the United States. Warranty
information for countries other than the United States is
available by contacting American Biophysics Corp.
International Department at [phone].
11
American Biophysics 1-877-699-8727
Gas Reset Tool Instructions
Gas Reset Tool (patent pending) should be used every time
tank is refilled, before connecting tank to regulator. If your
Liberty Plus fails to start, it may be the result of poor gas flow
from the propane tank through the regulator to the trap.
The Gas Reset Tool has been designed to reset the internal
mechanisms of the propane regulator and release any back
pressure from your propane tank. Please follow these steps:
CAUTION: Extinguish all smoking materials prior
to use of Gas Reset Tool.
For Customer Service: 1-877-699-8727
1. Shut down your Liberty Plus.
2. Completely close the propane tank valve by turning to the
“OFF” position. (turn valve clockwise)
3. Disconnect the regulator from the propane tank valve.
4. Screw the threaded end of the reset tool into the propane
tank valve until it is fully engaged. You may hear a small
“hiss” sound. This is the pressure being released from the
propane tank.
Note: the threads in the tank valve are left handed threads.
(turn valve counter clockwise)
5. Screw the regulator connector to the opposite end of the
reset tool until fully engaged.
Note: hold the reset tool to prevent it from backing out
of the tank.
6. The regulator and propane tank are now reset.
Disconnect the reset tool from the regulator connector
and the propane tank.
7. Re-attach regulator connector to the propane tank valve.
8. Slowly turn the propane tank valve on .
9. Restart your trap.
Customer Service
All of us at American Biophysics®want you to get complete
satisfaction from your Liberty Plus. Should you have any
problems you cannot resolve, simply call one of our trained
Customer Service Representatives at:
1-877-699-8727.
We will help you get up and running.
Troubleshooting
Step 3 - Disconnect Regulator
Step 4 - Screw in Threaded End of Reset Tool
Step 5 - Connect Regulator into Reset Tool

Mail completed form today or register on-line at www.mosquitomagnet.com
First Name Last Name
Address City
State/Province Zip Code Country
Phone Number Email Address
1. How did you find out about the Mosquito Magnet (check all that apply)?
Radio Ad Direct Mail TV Ad
Friend/Family Website Magazine Ad
Newspaper Ad News Article (newspaper, magazine, TV, etc.)
Frontgate In-Store Display Other
2. In your household who decided to purchase the Mosquito Magnet?
Male Female Both
3. What is your marital status?
Married Single
4. Are there any children in your household?
Yes No
5. What are the two most important reasons influencing this purchase?
Protection from mosquitoes that may transmit disease
Science/technology behind product
Recommendation of friend/family member
Recommendation of salesperson
Reputation of quality
Comfort
Received as gift
Other
6. What is your age?
25 – 35 36 – 45 46 – 55 56 – 70 70+
7. What is your level of education?
High School Diploma College Degree Graduate Degree Doctoral Degree Technical/Professional
8. Which best describes the size of your yard?
1/4 – 1/2 acre 1/2 – 3/4 acre 3/4 – 1 acre 1 – 2 acres
9. What is your annual household income?
$25,000 – 40,000 $40,000 – 60,000 $60,000 – 90,000 Over $90,000
10. What other brands of insect abatement have you tried?
Zappers Sprays Pesticides Other CO2Traps, Name:
11. Would you consider giving a testimonial once you are thoroughly convinced of the effectiveness
of the Mosquito Magnet?
Yes No
12. Would you recommend the Mosquito Magnet to a friend?
Yes No
13. Were the assembly directions and operation instructions explained clearly and simply?
Yes No
14. Did you require customer service?
Yes No
Consumer Confidentiality: All of the information that has been gathered on this reply card is solely for the internal sales and marketing efforts of American Biophysics Corporation. None of the
information that you may have provided will be sold, rented or leased to any other company, organization or agency for any purpose whatsoever. None of this information will be posted on our
company website or any other vehicle that can be obtained by the public domain. If you wish to make additional comments or testimonials about our product, please address them separately and
send them to our Marketing Department at the address listed inside the manual.
Product Registration
NECESSARY INFORMATION
In order to properly register your product
with American Biophysics®Corporation,
the following information is required.
Model: Circle One
Garden Defender Liberty
Liberty Plus Pro Pro Plus
Serial Number:
Date of purchase:
American Biophysics®Corporation
140 Frenchtown Rd.
North Kingstown, RI 02852
Place
First-Class
Stamp
Here