Most FANMIG 280-4N Minor User manual
User’s Manual for
semi-automatic welding machine
FANMIG
280-4N Minor
320-4N Minor
User Manual
Version 1.0 of 22.04.2021
Catalogue no:
280-4N Minor 51 000 22294
320-4N Minor 51 000 22334
Attention! Before starting work every person using or responsible for maintenance
work on this device should familiarize with the entire content of these User’s Manual.
This will optimize the use of device potential.
Attention! A copy of this User Manual should be stored at a location of device use and
always remain available to the operator.
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -2-
Contents
1. Health and Safety Manual
Warning! The device is may not be used for the purpose of pipe defrosting!
Information included on icons located on the device.
Use and maintenance of welding equipment may be dangerous. The user must
observe health and safety rules and regulations. Welding and cutting machines
may be used only by quali¿ed personnel. The national regulations for working with
this device and accident prevention should be kept up to date.
All ammable or combustible materials must be removed from the working area.
Do not weld in tanks where ammable liquids (fuel) were stored previously. Place
all combustible materials away from welding spatter.
Do not expose the device to rain or water vapour and do not spray water over it.
Do not weld without proper eye protection. Pay attention to providing safety for
bystanders against welding radiation.
Use ventilation and ¿lters in order to remove welding fumes from the work site.
Use individual ¿lters if the ¿ltering/ventilation system does not operate properly or
is not available.
Thank you for purchasing a semi-automatic welding machine FANMIG by MOST.
This manual booklet is common for two types of devices di-•ering in some technical parameters
We do believe that this product will meet your requirements. In order to ensure the correct use,
all the safety and operating manual should be read before operating this device.
1. Health and Safety Manual ..................................................................................................... 2
2. Maintenance (power supply and wire feeder) ....................................................................... 5
3. Technical description and operating conditions ..................................................................... 6
4. Technical data and device completion ................................................................................... 7
5. FANMIG 280-4N / 320-4N Minor control panel .................................................................... 8
6. Wire feeding system .............................................................................................................. 12
7. Device commissioning .......................................................................................................... 14
8. Welding ................................................................................................................................. 15
9. Spare parts ........................................................................................................................... 16
10. Device operation defects .................................................................................................... 21
11. Electrical scheme ................................................................................................................ 22
12. Recycling ............................................................................................................................ 23
13. Declaration Of Conformity ................................................................................................... 24
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -3-
Stop your work immediately after ¿nding damage to the power cords. Do not touch
the damaged cords. Prior to repair or maintenance disconnect the device from
power source. Never use the device with damaged power cords.
Keep a ¿re extinguisher close to the welding location. After ¿nishing welding check
work station against ¿re hazard.
Never try to ¿x a damaged gas reducer on your own. In case of malfunction repla-
ce the reducer to a fully functional one.
Electromagnetic interference.
The device may inuence other devices sensitive to electromagnetic interference
(robots, computers, etc.)
Always ensure that the devices within the welding work station are resistant to
interference. In order to minimize interference it is recommended to use possibly
shortest welding cables arranged in parallel.
Always work in a distance at least 100 m from other sensitive devices. Always
make sure that the installation is grounded.
In case of interference with other devices, shield the cables or use appropriate
¿lters.
The device is compliant with the currently applicable standards. In accordance
with IEC 60974-10 classi¿ed as class A and is intended for use in workshop and
industrial conditions. The device application nearby to residential buildings, espe-
cially the power supply using a home electrical network, may interfere with the
operation of other electrical or telecom devices.
The user is responsible for the correct device connection and removal of
potential electromagnetic disturbances.
INTRODUCTION
Commissioning and normal operation are possible only after reading the carefully reading
following manual. MIG/MAG welding requires meeting the requirements for electric arc welding
regulations and complying with ¿re regulations. Device operator should be equipped with
appropriate personal protective equipment. It is necessary to use a set of compatible protective
equipment
with the provisions of the European Parliament and the Directive 2016/425/EEC. Personal
protective equipment includes: welding mask, welding gloves, protective apron, leather shoes,
non-ammable welding clothing.
Despite the high technical standard of the device, the personnel should demonstrate consi-
derable discipline in terms of health and safety requirements that protect against harmful and
health hazardous factors resulting from welding technology.
OPERATING CONDITIONS
In order to ensure adequate service life and trouble-free operation:
- do not place or use this device on an inclined surface of more than 15º,
- do not use the device for pipe defrosting,
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -4-
ATTENTION
GASES AND FUMES
Using MIG / MAG techniques produces harmful gases and fumes containing ozone and hydro-
gen as well as oxides or metal particles. Therefore, the welding work station should
be ¿tted with very good ventilation (dust and smoke extraction or airy location) Metal surfaces
intended for welding should be free from chemical contamination, especially degreasers (so-
lvents) that
decompose during welding process and produce toxic gases. Welding of galvanized, cadmium-
-coated or chromium-plated parts is permitted only when a suction and ¿ltering device is ¿tted,
and with introduction of fresh air to the welding work station.
RADIATION
Ultraviolet radiation emitted during welding is harmful to eyesight and skin. Therefore a welding
mask with protective ¿lters is required. Welding work station should meet certain requirements,
including:
• adequate lighting system,
• ¿xed or movable protection screens, governing bystanders against radiation e-•ects
(depending on requirements),
• placed in a room with appropriate wall colour (absorption of UV radiation)
FIRE PROTECTION
Welding work station should be located at a safe distance from ammable materials placed
especially on the oor or walls. All ammable materials need ¿re protection against hot metal
drops. It is recommended to ¿t the work station with ¿re blankets and ¿re extinguishers.
PROTECTION AGAINST ELECTRIC SHOCK
It is unacceptable to connect the device to an improper installation or to an installation with
unveri¿ed zeroing e-ciency. It is prohibited to use of device with shields removed or remove
the external shields while the device is connected to electric network. It is not allowed to work
on a suspended device (e.g. using a crane or a gantry). Only authorized persons should per-
form maintenance and repair works keeping it in compliance with the safety conditions applica-
ble to renovation equipment.
- the device needs to be located in a place with free clean air circulation (to and from the fan
without obstacles). When connected to electrical network the device must not be covered (with,
for example, paper or cloth)
- minimize the amount of dirt and dust that could get inside the device,
- device has an IP23S protection rating for housing and may be
- do not use the device for welding tanks previously used for ammable substances storing.
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -5-
2. Maintenance (power supply and wire feeder)
ATTENTION: In order to carry out any repair or maintenance activity, it is recommended to
contact your nearest technical support of RYWAL-RHC (a list of authorized service shops is
available on the last page of the manual).
In the event of noticing any damage, the welder should stop working, disconnect the device
from power supply and report it to direct supervisor or appropriate service - RYWAL-RHC
technical support.
General maintenance (daily)
- check the condition of cables and connections, replace if necessary,
- remove spatter from the gas nozzle of the welding torch, spatter may transfer with the shiel-
ding gas to the welding arc, tend to disrupt the shielding gas ow and can e-•ect in a short
circuit,
- check condition of welding torch, replace if necessary,
- check condition and operation of the cooling fan; keep the cooling air inlet and outlet openings
- keep it clean at all times.
Periodic maintenance (every 3 months at least)
Periodic maintenance frequency can be increased depending on the environment conditions
in which the device is operating. Maintenance scope:
- using a stream of dry air (at low pressure) remove the dust from the outer parts of the casing
and from inside of the welding device,
- check and tighten all the screws,
- check the state of all electrical contacts and correct if necessary.
ATTENTION: Power supply must be disconnected from the device before any
maintenance and service work. After each repair, perform a proper check to ensure
safe use.
Mandatory device checks
According to the Labour Code provisions: „All responsibility for the safe use of machinery
and equipment shall be borne by the owner.”
This results in the obligation to perform periodic and post-repair checks and inspections of
equipment.
Periodic tests are carried out at least once a year (legal basis EN ISO 17662 clause 4.2), and
post-repair tests after each repair that restored welding functionality (legal basis: EN 60974-4
clause 4.6).
All above services are performed by the technical support of RYWAL-RHC.
In accordance with Regulation 2019/1784 (EU) Annex II pt. 2. b1,
The RYWAL-RHC company provides information on repairs and maintenance to
PROFESSIONAL TECHNICAL SUPPORT PROVIDERS under the terms of the regulation.
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -6-
3. Technical description and operating conditions
FANMIG 280-4N / 320-4N Minor is a semi-automatic welding machine designed for MIG/MAG
gas shield welding. It is a compact-sized device including electrical power supply and wire feeder
located inside a single housing. FANMIG 280-4N Minor and FANMIG 320-4N Minor include a 4-roll
wire feed systems.
All devices include the same type of feeding roll see chapter 6.
The device has excellent welding properties and has a wide application range. It may be used for
sheet thickness between 0.8 mm and 8 mm. Welded material types cover carbon steel, stainless
steel or aluminium (after feeder and holder conversion).
Recommended wire diameters are 0.6 mm to 1.2 mm.
Wire feed speed may be set between 1 and 19 m/min, the welding current has a step setup setting
(FANMIG 280-4N - 10 steps, FANMIG 320-4N - 12 steps).
Transformer and the induction coil are made of copper (insulation class F) and are fan cooled.
The device is sensor protected against overheating.
Made in accordance with EN 60974-1 standard.
«Safety requirements for arc welding equipment. Welding energy sources».
Wire feeder may be used for spools between 5 to 15 kg. Basket spools require an additional
adapter.
Operating Conditions
Range of air temperatures:
Operating temperature: -10ºC to +40ºC,
Transport and storage temperature from -25ºC to +55ºC.
Relative air humidity up to 50% at +40ºC and up to 90% at +20ºC.
Transport.
Be especially careful when transporting device with a forklift or a lift truck
- risk of damage to the device’s chassis.
Use only suitable slings for a vertical transport by crane. Before the device transporting, remove
gas cylinder from the rear shelf and disconnect gas and electrical grid. The maximum permissible
inclination angle for transport is 10°.
ATTENTION: Danger of falling or overturning the device during transport!
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -7-
4. Technical data and device completion
Parameter Unit FANMIG 280-4N FANMIG 320-4N
Electrical power supply V/Hz 3x400/ 50/60 3x400/ 50/60
Network protection [slow-blow] A 16 25
Power factor cos 0,9 0,9
Power S1max kVA 11,1 14,3
Welding current range A 40 - 290 40 - 340
Idle mode power consumption W 63 63
Power source e-ciency % 79 80
Welding current [A] at:
25% work cycle
30% work cycle
60% work cycle
100% work cycle
A/V -
290 A / 28,5 V
210 A / 24,5 V
170 A / 22,5 V
340 A / 31 V -
230 A / 25,5 V
200 A / 24 V
Welding current set point number 10 12
Wire feeder 4-roll (-2N/4N) 4-roll
Wire feeding speed mm 1-19 1-19
Welding torch cooling Air Air
Welding Torch (gas) M 24 lub M25 MOST M 24 lub M25 MOST
Protection class IP 23S IP 23S
Insulation class H H
Noise emission dB(A) <70 <70
EMC noise level according to PN60974-10 Class A Class A
Weight kg 88 99
Dimensions (length x width x height) mm 868x500x806 868x500x806
Table 1: FANMIG 280-4N / 320-4N Minor technical data
Completion
3 m long ground cables.
3 m long power cable.
Gas hose included. On request the devices are supplied with di-•erent cable lengths or
welding torches.
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -8-
5. FANMIG 280-4N / 320-4N Minor control panel
Figure 1: Device front panel
V1 - main switch
V3 - welding current accurate switch
P1 - Minor version control panel (see Fig. 2)
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -9-
5.1 Minor version control panel
5
4
3
2
1
6 7 8 9
10
11
12
Figure 2: Control panel (P1 as on Fig.1) on Minor version
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -10-
1 Button
• Wire installation (of a new spool)
• Deleting/Resetting parameters (simultaneously press button 2)
2 Button
• Gas test
• Deleting/Resetting parameters (simultaneously press button 1)
3 Button
• Switch between 2-step and 4-step
• Pressing longer than for 2 s switches on spot welding (led 11 lights up) or intermittent
• (led 11 blinks)
• Entering secondary parameters - see table 3 (press simultaneously with the button 5)
4 LED 2-step
5 Button
• Entering secondary parameters - see button description 6 (press simultaneously with the
button 3)
6
Display shows secondary parameters
• Wire feeding speed (adjustable)
• PrG – gas pre-ow [s]
• PoG – gas post-ow [s]
• brn – wire burn time [s]
• SPo – spot-welding time [s] (active spot-welding only)
• Int - break time at intermittent welding [s] (active spot-welding only)
7LED cooling system fault (optional)
8 LED overheat Let the device to cool down using a fan
9 Display shows secondary parameters
10 LED 4-cycle
11 LED
• Switches on – spot welding
• Blinks – intermittent welding
12 Knob
• Sete the feed speed
• Selects secondary parameters
Table 2: Minor control panel function markings
Attention! Displays 6 and 8 do not show A/V current value when welding.
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -11-
+Press 1 and 2 simultaneously, so all function values return to
factory settings.
5.2 Return to factory settings (RESET)
5.3 Setting range of the individual welding functions:
Symbol on
Display 6 Parameter MIN MAX Unit
SPo Welding time for spot weld. and interm.
welding 0,5 20 s
Int Pause time at intermittent welding0,5 20 s
brn Wire burn time 0 0,75 s
PrG Gas pre-ow 0 20 s
PoG Gas post-ow 0 20 s
Table 3: Welding functions and ranges
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -12-
Pos. Catalogue no. Nazwa Name
1 5630 Podkładka mocująca Retaining washer
2,3,4 5633 Rolka zębata komplet TR 402/404 Gear Wheel TR 402/404 set
5 5634 Ramię dociskowe prawe TR 404 Arm TR 404
6 5635 Tuleja 10 Shaft 10
7 5630 Podkładka mocująca RA 5 Retaining ring for shaft RA5
8 5636 Tuleja 6 Shaft 6
9 5637 Sprężyna górna TR 404 Spring TR 404
10 5638 Korpus dociskowy TR 404 Fixing arm compl. TR 404
12 5468 Silnik Motor
13 5639 Dysza wejściowa 2R/4R mała Liner for Feeder 2roll,4roll Small
14 5630 Podkładka mocująca Retaining washer
15 5640 Śruba M5x10 Screw M5x10
6. Wire feeding system
Figure 3: FANMIG 280-4N / 320-4N feeding system
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -13-
Pos. Catalogue no. Nazwa Name
16 5641 Śruba M6x16 Screw M6x16
17 5642 Koło zębate napędowe TR 404 Gear Wheel center TR 404
18 5643 Osłona plastikowa TR 404 Fixing Cup TR 404
19 5644 Śruba M4x12 Screw M4x12
20 5645 Osłona TR 404 Metal cover TR 404
21 5640 Śruba M6x16 Screw M6x16
22 5646 Nakrętka rolki mała Bolt Small
23 5113007783 Rolka 0.6-0.8 22/30 Roll 0.6-0.8 22/30
5113007826 Rolka 0.8-1.0 22/30 Roll 0.8-1.0 22/30
5113007862 Rolka 1.0-1.2 22/30 Roll 1.0-1.2 22/30
5113007956 Rolka 1.2-1.6 22/30 Roll 1.2-1.6 22/30
5113997828 Rolka 0.8-1.0 22/30 AL Roll 0.8-1.0 22/30 AL
5113007863 Rolka 1.0-1.2 22/30 AL Roll 1.0-1.2 22/30 AL
5113007960 Rolka 1.2-1.6 22/30 AL Roll 1.2-1.6 22/30 AL
5113007895 Rolka 1.0-1.2 22/30 TD Roll 1.0-1.2 22/30 TD tube wire
5113007899 Rolka 1.2-1.4 22/30 TD Roll 1.2-1.4 22/30 TD tube wire
24,25,
26
5647 Koło zębate dolne komplet TR 404 Gear wheel upper TR 404 set
27 5649 Tuleja TR 404 Shaft TR 404
28 5650 Korpus zespołu podającego TR 404 W. Feeder Body TR 404 Set
29 5651 Rurka pośrednia TR 404 Tube for W. Feeder pro TR 404
30 5652 Ramię dociskowe lewe TR 404 Arm left TR 404
31 5653 Klin Key
32 5654 Podkładka Washer
A 5976
5977
Ramię lewe TR 404
Ramię prawe TR 404
Arm left TR 404
Arm right TR 404
B 5978 Korpus dociskowy TR 404 Fixing arm compl. TR 404 set
C5618 Zespół napędowy kompletny TR 404 0.8-
1.0 bez silnika
WF body TR 404 0.8-1.0 complet without
Motor
Attention: The sets A and B are included in set C
Table 4: Feeding system spare parts for FANMIG 280-4N / 320-4N Minor.
The drawing and a table for feeding system parts of TR404
(marked with a stylized letter „H” on the aluminium housing). In
the case of parts for older versions of FANMIG devices, please
contact RYWAL-RHC technical support.
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -14-
7. Device commissioning
7.1 Power connections
The device is powered from a three-phase 400V/50Hz. The required protection is a slow-blow
fuse 16 A (FANMIG 280-4N) or 25 A (FANMIG 320-4N) with grounding. Plug type CEE FANMIG
280-4N 16 A 5-pin, FANMIG 320-4N 32 A 5-pin.
7.2 Welding torch connection
The welding torch should be connected with euro socket and screwed with a nut. The torch
insert and contact tip must refer to welded wire diameter – see torch catalogue.
7.3 Feed rolls in wire feeder (see table 4).
Each roll includes two notches - marking is stamped on roll side.
The notch must reect the wire type and diameter. When changing the wire, make sure that the
correct roll is applied.
7.4 Mounting the spool on a feeder and wire feeding in the welding torch - button 1 as on
Fig.2.
The wire spool should be installed on the feeder so the wire unwinds from the bottom of the
spool and goes straight to feed rolls. If the spool is based on a metal basket, use a basket spo-
ol adapter. It is necessary to secure the spool so the basket does not touch the device metal
casing
Th spool’s braking force is controlled by a bolt inside the spool’s sleeve.
Unroll a short wire section from spool. Align the wire ending (cutting it o-• with o-•-cuts) and
guide it onto feeding roll with upper press mechanism is lifted! Than guide the wire through eu-
ro-socket and welding torch Press the pressure arm after inserting the initial 20 cm wire section
into the welding torch and continue feeding wire automatically by pressing torch button. It is
recommended to demount the gas nozzle and the tip contact when inserting the wire into the
torch. It is not allowed to use excessive pressure on the rolls, as it may lead to wire deformation
and feeding issues.
7.5 Gas hose and shielding gas ow.
Shielding gas hose connects the device to gas bottle. Gas reducer located on the cylinder
used for gas mixtures and argon. Cylinder should be located on the rear shelf of the device and
secured with a chain to prevent tipping over. Having the cylinder placed
and gas hose connected to the back of welding device, unscrew the cylinder valve and set
pressure level with the reducer. Gas ows out after pressing the button 2. Recommended gas
ow rate is 10 x the wire diameter and equals the gas ow in litres per minute
7.6 Aluminium welding
For aluminium welding use rolls with U-shaped notch (see table 4). Recommended wire type:
AlMg3 or AlMg5 and 1.0 mm diameter. Welding torch (suggested m length) should be accor-
dingly adjusted and have its insert replaced to a Teon one and tip ¿tting the wire diameter.
Having the above operations completed and connection checked, the device is ready for ope-
ration.
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -15-
8. Welding
For an approximate setting of the correct welding current, use the following empirical formula =
14 + 0,05 x I2.
After turning the device on with main switch V1 (see Fig. 1) and setting the gas shield ow
(see 6.5) and wire (see 6.4) you can proceed with setting the welding current. Welding voltage
(current) is set with V2 and V3 switches.
Use the knob 12 to set the wire feed speed (see Fig. 2). Welding arc should be stable and pro-
duce minimal amount of spatter. Use button 3to set following available welding modes:
Button 4 - 2-cycle continuous welding
Button 10 - 4-cycle continuous welding
Buttons 4 and 11 (LED is on) - 2-cycle spot welding
Buttons 4 and 11 (LED blinks) - 2-cycle intermittent welding
Buttons 10 and 11 (LED is on) - 4-cycle spot welding
Buttons 10 and 11 (LED blinks) - 4-cycle spot welding
In order to set the spot or intermittent welding, press and hold button 3 for longer than 2 se-
conds. A choice between 2- and 4-cycle when constant welding is made by pressing button 3.
Wire
diameter
[mm]
Wire
feeding
speed
[m/min]
Max.
feeding
speed
[m/min]
Weight
of 1 m
of wire
[g]
Wire
consumption
per minute for
maximum feed
speed
[g/min]
Wire consumption
per hour for the
maximum feed
speed
[g/h]
Solid steel wire
0,6 2 - 5 5 2,3 11,5 690
0,8 3 - 6 6 4 24 1440
1,0 3 - 12 12 6 72 4320
1,2 4 -18 18 9 162 9720
Stainless steel wire
0,6 2 - 5 5 2,3 11,5 690
0,8 3 - 6 6 4 24 1440
1,0 3 - 12 12 6 72 4320
1,2 4 -18 18 9 162 9720
Aluminium wire
0,6 2 - 5 5 0,8 4 240
0,8 3 - 6 6 1,3 7,8 468
1,0 3 - 12 12 2 24 1440
1,2 4 -18 18 3 54 3240
Table 5: Approximate wire and gas consumption for MIG / MAG welding.
Wire diameter
[mm] Recommended gas ow
[l/min] Gas consumption per hour of welding
[l/h]
(recommended gas ow * 60 minutes)
0,6 6 6 * 60 = 360
0,8 8 8 * 60 = 480
1,0 10 10 * 60 = 600
1,2 12 12 * 60 = 720
1,6 16 16 * 60 = 960
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -16-
9. Spare parts
Figure 4: FANMIG 280-4N Minor spare parts
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -17-
No.
Indeks Nazwa Description szt/pc
1V0016-2 Cokół DIN 40mm DIN plinth 40mm 1
2 2532 Tuleja mocująca szpulę czarna Spool Holder Black 1
3 3598 Uchwyt lewy INDUSTRY Handle - Holder L INDUSTRY 1
4 3599 Uchwyt prawy INDUSTRY Handle - Holder R INDUSTRY 1
5 4212 Folia MINOR new HS4615 Film MINOR new HS4615 1
6 302P010000 Wąż gazowy 30 4,9x1,5 Hose 30 Gas 4,9x1,5 0,8 m
73253-1 Koło przednie 3370 PRO 100 P62 LW46 kl. Front Front Wheel 3370 for 100 1
8 4094 Koło przednie z hamulcem 3377 PRO 100 P62 LW46 Front Front Wheel 3377 for 100 with brake 1
9 VM0049 Kabel zasilający 16A CGSG4x1,5 Mains Cable 16A CGSG4x1,5 1
10 VM0023 Kabel masowy 3 m 300 A 35-50 Earthing Cable 3 m 300 A 35-50 1
11 2164 Pokrętło, czerwony kapsel, podkładka 28N6 Knob 28N6+Red cover, washer 1
12 2446 Koło tylne PVO 200x50x20 Rear wheel 200x50x20 2
13 2603 Przyłącze 1/4 6mm (kod 8685) Connector G1/4 6mm 1
14 1812 Konektor 2pol. DK 021 Gas heater connector 1
15 2389 Konektor CUF 5/36 (szary) Connector CUF 5/36 gray 3
16 2389 Konektor CUF 5/36 (szary) Connector CUF 5/36 gray 6
17 2389 Konektor CUF 5/36 (szary) Connector CUF 5/36 gray 2
18 BG-90625 Gniazdo EURO ALFA IN VS040312-1 Connector EURO ALFA IN VS040312-1 1
19 3440 Osłona gniazda EURO Cover Connector EURO 1
20 2602 Nakrętka G1/4" (kod 8690) Nut G1/4" 1
21 R 0141 Nakrętka i uszczelnienie zaworu G1/4 2557 Nut G1/4 + insulation for valve 2557 1
22 3461 Kratka wentylatora FG-12 Sunon Grating FG-12 Fan Sunon 2
23 4236 Filtr FC61113 + R (3x150N+027N-Z01/08) Filter FC 61113 + R (3x150N+027N-Z01/08) 1
24 3252 Filtr FZ 730 43 Filter FZ 730 43 3
25 4121 Zawias O430-30 M5 Hinge O430-30 M5 2
26 3979.d Płytka PCB MAJOR/MINOR/SYNERGY.d PCB MAJOR/MINOR/SYNERGY.d 1
27 4321-2 Zespół podający TR404 1.0-1.2 W. Feeder TR404 1.0-1.2 1
28 V9040040 Mocowanie kabla S12 Cable clamp S12 1
29 AO-20610 Szybkozłączka żeńska 35-70 panel Quick Connector 35-70 Panel Socket 2
30 VS040258 Łańcuch na butlę 70 cm Chain 70 cm 2
31 VM0203-1 Przewód Ekonom 280 (szybkozłączka. 12mm) Cables 280 (Quick Connector 12mm) 1
32 R 0078 Słupek dystansowy KOV DA5M3X10 Distance Post KOV DA5M3X10 4
33 276834 Stycznik MOELLER DILM 12-10 (24V/50Hz) Contactor MOELLER DILM 12-10 (24V/50Hz) 1
34 VM0114.YQ Wiązka ALF 349.Y SYNERGY Bundle ALF 349.Y SYNERGY 1
35 AO-42620 Zacisk D9.5 Clamp D9.5 2
36 2015 Pokrętło strzałkowe OM-C/5 czarne Knob arrow OM-C/5 Black 1
37 1343 Pokrętło strzałkowe OM-R/5 czerwone Knob arrow OM-R/5 Red 1
38 2523-1 Dłąwik ALF 280 (Al) Choke ALF 280 (Al) 1
39 T28.P Transformator 280 ALF + przyłacza Transformer 280 ALF + Switch 1
40* 3270-4Z Transformator JSC E96.32/T01.1 (JSC E3232-0451) z
ltrem
Transformer JSC E96.32/T01.1 with lter 1
41 1195-1 Prostownik PTS 240 z 2 x 10nF Rectier PTS 240 1
42 2557 Elektrozawór 24V 50Hz AC typ 5541 Solenoid Valve 24V 50Hz AC type 5541 1
43 4172 Wentylator SUNON A2123 HBL (7).GN Fan A2123-HBL (7).GN 2
44 1005 Włącznik ON/OFF VS 16 1102 A8 Switch ON/OFF 1
45 2285-1 Wyjście OBO 13.5 szare 13.5x12 – nakrętka Outlet 13.5 Gray 13.5x12 - NUT 1
46 2285 Wyjście OBO 13.5 szare 13.5x12 – korpus Outlet 13.5 Gray 13.5x12 - BODY 1
47 2681 Zamek A3-40-625-12 Lock A3-40-625-12 2
48 1096 Włącznik VS16 11510001A1 Switch VS16 11510001A1 1
49 1835-1 Termostat SCOMES 115oC Theromostat 115 C 1
50 V0002 Panel przedni Alf 400 Panel front Alf 400 1
51 V0003 Panel tylni Alf 400 Panel back Alf 400 1
52 V0001 Podstawa Alf 400 Ground Alf 400 1
53 V0017 Mocowanie tulei Alf 400 Support of spool Alf 400 1
54 V0011 Mocowanie butliAlf 400 Holder gas bottle Alf 400 2
55 V0013 Mocowanie dławikaAlf 400 Support of chokeAlf 400 1
56 V0008 Osłona boczna lewa górna Alf 400 Case left spool Alf 400 1
57 V0009 Osłona boczna lewa dolna Alf 400 Case left lower Alf 400 1
58 V0007 Osłona boczna prawa Alf 400 Case right Alf 400 1
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -18-
Nr Indeks Nazwa Description szt/pc
59 V0006 Osłona górna Alf 400 Cover upper Alf 400 1
60 V0010 Osłona panelu sterowania Alf 400 Case regulator Alf 400 1
61 V0029 Panel przedni ALF 280-320 compact Synergy neutral Front panel Alf 280-320 compact Synergy neutral 1
62 V0005 Podwozie Alf 400 Carriage unit Alf 400 1
63 V0004 Podpórka Alf 400 Support Alf 400 1
64 V0015 Rurka przednia Alf 400 Tube of handle Alf 400 1
65 V0012 Rurka podwozia Alf 400 Tube of carriage unit Alf 400 1
66 V0018 Rozpora Alf 400 Strut Alf 400 1
Table 6: FANMIG 280-4N Minor spare parts
Figure 5: FANMIG 320-4N Minor spare parts
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -19-
No.
Indeks Nazwa Description szt/pc
1V0016-2 Cokół DIN 40mm DIN plinth 40mm 1
2 2532 Tuleja mocująca szpulę czarna Spool Holder Black 1
3 3598 Uchwyt lewy INDUSTRY Handle - Holder L INDUSTRY 1
4 3599 Uchwyt prawy INDUSTRY Handle - Holder R INDUSTRY 1
5 4212 Folia MINOR new HS4615 Film MINOR new HS4615 1
6 302P010000 Wąż gazowy 30 4,9x1,5 Hose 30 Gas 4,9x1,5 0,8 m
73253-1 Koło przednie 3370 PRO 100 P62 LW46 kl. Front Front Wheel 3370 for 100 1
8 4094 Koło przednie z hamulcem 3377 PRO 100 P62 LW46 Front Front Wheel 3377 for 100 with brake 1
9 VM0049 Kabel zasilający 16A CGSG4x1,5 Mains Cable 16A CGSG4x1,5 1
10 VM0023 Kabel masowy 3 m 300 A 35-50 Earthing Cable 3 m 300 A 35-50 1
11 2164 Pokrętło, czerwony kapsel, podkładka 28N6 Knob 28N6+Red cover, washer 1
12 2446 Koło tylne PVO 200x50x20 Rear wheel 200x50x20 2
13 2603 Przyłącze 1/4 6mm (kod 8685) Connector G1/4 6mm 1
14 1812 Konektor 2pol. DK 021 Gas heater connector 1
15 2389 Konektor CUF 5/36 (szary) Connector CUF 5/36 gray 3
16 2389 Konektor CUF 5/36 (szary) Connector CUF 5/36 gray 6
17 2389 Konektor CUF 5/36 (szary) Connector CUF 5/36 gray 2
18 BG-90625 Gniazdo EURO ALFA IN VS040312-1 Connector EURO ALFA IN VS040312-1 1
19 3440 Osłona gniazda EURO Cover Connector EURO 1
20 2602 Nakrętka G1/4" (kod 8690) Nut G1/4" 1
21 R 0141 Nakrętka i uszczelnienie zaworu G1/4 2557 Nut G1/4 + insulation for valve 2557 1
22 3461 Kratka wentylatora FG-12 Sunon Grating FG-12 Fan Sunon 2
23 4236 Filtr FC61113 + R (3x150N+027N-Z01/08) Filter FC 61113 + R (3x150N+027N-Z01/08) 1
24 3252 Filtr FZ 730 43 Filter FZ 730 43 3
25 4121 Zawias O430-30 M5 Hinge O430-30 M5 2
26 3979.d Płytka PCB MAJOR/MINOR/SYNERGY.d PCB MAJOR/MINOR/SYNERGY.d 1
27 4321-2 Zespół podający TR404 1.0-1.2 W. Feeder TR404 1.0-1.2 1
28 V9040040 Mocowanie kabla S12 Cable clamp S12 1
29 AO-20610 Szybkozłączka żeńska 35-70 panel Quick Connector 35-70 Panel Socket 2
30 VS040258 Łańcuch na butlę 70 cm Chain 70 cm 2
31 VM0203-1 Przewód Ekonom 280 (szybkozłączka. 12mm) Cables 280 (Quick Connector 12mm) 1
32 R 0078 Słupek dystansowy KOV DA5M3X10 Distance Post KOV DA5M3X10 4
33 276834 Stycznik MOELLER DILM 12-10 (24V/50Hz) Contactor MOELLER DILM 12-10 (24V/50Hz) 1
34 VM0114.YQ Wiązka ALF 349.Y SYNERGY Bundle ALF 349.Y SYNERGY 1
35 AO-42620 Zacisk D9.5 Clamp D9.5 2
36 2015 Pokrętło strzałkowe OM-C/5 czarne Knob arrow OM-C/5 Black 1
37 1343 Pokrętło strzałkowe OM-R/5 czerwone Knob arrow OM-R/5 Red 1
38 2523-1 Dłąwik ALF 280 (Al) Choke ALF 280 (Al) 1
39 T28.P Transformator 280 ALF + przyłacza Transformer 280 ALF + Switch 1
40* 3270-4Z Transformator JSC E96.32/T01.1 (JSC E3232-0451) z
ltrem
Transformer JSC E96.32/T01.1 with lter 1
41 1195-1 Prostownik PTS 240 z 2 x 10nF Rectier PTS 240 1
42 2557 Elektrozawór 24V 50Hz AC typ 5541 Solenoid Valve 24V 50Hz AC type 5541 1
43 4172 Wentylator SUNON A2123 HBL (7).GN Fan A2123-HBL (7).GN 2
44 1005 Włącznik ON/OFF VS 16 1102 A8 Switch ON/OFF 1
45 2285-1 Wyjście OBO 13.5 szare 13.5x12 – nakrętka Outlet 13.5 Gray 13.5x12 - NUT 1
46 2285 Wyjście OBO 13.5 szare 13.5x12 – korpus Outlet 13.5 Gray 13.5x12 - BODY 1
47 2681 Zamek A3-40-625-12 Lock A3-40-625-12 2
48 1096 Włącznik VS16 11510001A1 Switch VS16 11510001A1 1
49 1835-1 Termostat SCOMES 115oC Theromostat 115 C 1
50 V0002 Panel przedni Alf 400 Panel front Alf 400 1
51 V0003 Panel tylni Alf 400 Panel back Alf 400 1
52 V0001 Podstawa Alf 400 Ground Alf 400 1
53 V0017 Mocowanie tulei Alf 400 Support of spool Alf 400 1
54 V0011 Mocowanie butliAlf 400 Holder gas bottle Alf 400 2
55 V0013 Mocowanie dławikaAlf 400 Support of chokeAlf 400 1
56 V0008 Osłona boczna lewa górna Alf 400 Case left spool Alf 400 1
57 V0009 Osłona boczna lewa dolna Alf 400 Case left lower Alf 400 1
58 V0007 Osłona boczna prawa Alf 400 Case right Alf 400 1
User Manual
Version 1.0 of 22.04.2021
FANMIG 280-4N Minor
320-4N Minor -20-
No.
Indeks Nazwa Description szt/pc
59 V0006 Osłona górna Alf 400 Cover upper Alf 400 1
60 V0010 Osłona panelu sterowania Alf 400 Case regulator Alf 400 1
61 V0029 Panel przedni ALF 280-320 compact Synergy neutral Front panel Alf 280-320 compact Synergy neutral 1
62 V0005 Podwozie Alf 400 Carriage unit Alf 400 1
63 V0004 Podpórka Alf 400 Support Alf 400 1
64 V0015 Rurka przednia Alf 400 Tube of handle Alf 400 1
65 V0012 Rurka podwozia Alf 400 Tube of carriage unit Alf 400 1
66 V0018 Rozpora Alf 400 Strut Alf 400 1
Table 7: FANMIG 320-4N Minor spare parts
This manual suits for next models
1
Table of contents
Other Most Welding System manuals
Most
Most Fanmig 322 mobil Pulse User manual
Most
Most PONTIG 202 AC/DC MOST User manual
Most
Most Fanmig 201 LCD User manual
Most
Most PONTE 201 PRO MOST User manual
Most
Most MasterCut 120 CNC User manual
Most
Most Fanmig 522i Pulse User manual
Most
Most Fanmig J5 MOST User manual
Most
Most PONTIG 210 DC MOST User manual
Popular Welding System manuals by other brands
WIA
WIA UTILITY UTAC13-0 owner's manual
Helvi
Helvi PC75 instruction manual
Parweld
Parweld XTI-303 AC/DC instruction manual
Eastwood
Eastwood VERSA-CUT 40 Assembly and operating instructions
Hobart Welding Products
Hobart Welding Products Hobart 300/300 owner's manual
Leister
Leister TWINNY T7 operating instructions
CARBONE
CARBONE Digi-Tig200ACDC PULS Operator's manual
INTERNATIONAL WELDING TECHNOLOGIES
INTERNATIONAL WELDING TECHNOLOGIES Lynx4 Quickshot operating instructions
Miller
Miller MigMatic S400i owner's manual
Miller
Miller TRAILPOWER 5GA1 owner's manual
Chicago Electric
Chicago Electric MIG 180 Owner's manual & safety instructions
MAX ARC
MAX ARC MAX-ARC 250 Operation instructions