MOTION BLINDS CM-03-E User manual

Motionblinds Manual
User Manual
Roller Blind
Motor CM-03-E
EN

2
Con
forms to
UL Std. 325
Cleaning
Follow these general rules when cleaning the
outside of the device and its components:
Use a damp, soft, lint-free cloth. Avoid getting
moisture in openings.
Do not use aerosol sprays, solvents, alcohol, or
abrasives.
Service & Support
Do not perform repairs yourself. Do not attempt to
open the device or disassemble it. You run the risk
of electric shock and voiding the limited warranty.
No user-serviceable parts are inside.
Warranty Service
First follow the advice in this manual. If the product
appears to be damaged or does not function
properly, go to your local dealer for instructions on
how to obtain warranty service.
Recycle
This marking indicates that this product should
not be disposed with other household wastes
throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources. To
return your used device, please use the return and
collec-tion systems or contact the retailer where
the product was purchased. They can take this
product for environmental safe recycling.
Read the instructions carefully
before assembling and using
the product. Assembly can be
completed by non-professionals.
For indoor use only.
Young children can strangle
themselves with the loop of
pull cords, chains and tapes,
and cords that operate window
coverings.
To avoid strangulation and
entanglement, keep cords out
of reach of young children.
Cords may ensnare a child’s
neck.
Move beds, cots and furniture
away from window covering
cords.
Do not tie cords together.
Make sure cords do not twist
together and form a loop.
WARNING

3
USB-C charging port
LED (Battery/Reset indicator)
End position button
Reset/Program button
Pull control
Buttons and functions
ENGLISH

4
MN180 020_20 180713
1/4
2 x 2 x 2 x 4 x
B
Max. 1/8 "
Bracket Motorized
Opening width
Inside mount Outside mount
Outside mount
Inside mount
Deduct 1 1/4 inch from opening
width for screw positions
1
2
Install the blind
Activate the blind
Follow the steps in the installation instructions to install the blind.
To activate the blind, connect it to a standard USB-C 5V power supply via a USB-C cable.
This can be your smartphones power adapter, for example.

5
1234-567-8901
1234-567-8901 1234-567-8901
3
4
Add Eve MotionBlinds to your platform
Add Eve MotionBlinds to the platform of your choice and make sure to
have a compatible Thread Border Router.
More information : motionblinds.com/eve/matter
Now you can easily add Eve MotionBlinds to your smart home in just a few steps by scanning
the Matter Setup Code using the app of your favorite platform. Scan the Matter Setup Code
to add it your platform.
Eve MotionBlinds needs end positions to work properly. End positions can be programmed in
two ways. In the Eve app or by the end position programming button on your blind. (Step 5)
After scanning you can hide your Matter Setup Code.
Setup the blind
ENGLISH

6
6
5Set end positions
Beside setting the end positions by the app you are able to set the end positions by
pressing the button on the motor. Pull and hold the chain until the blind has reached
the bottom position. If the blind moves in the opposite direction, release the chain and
pull and hold again.
Adjust until the desired bottom position has been reached.
Save your bottom position
When your blind is positioned at your bottom position hold the button until the blind moves up
and down to save your bottom position.

7
8
7Move your blind to the top position
Save your top position
Pull and hold the chain until the blind has reached the top position.If the blind
moves in the opposite direction, release the chain and pull and hold again.
Adjust until the desired top position has been reached.
When your blind is positioned at your top position hold the button until the blind moves up
and down to save your top position.
ENGLISH

8
3 s
10
9
Remove your (bottom/top) position
Hold the end position program button for 3 seconds to remove your (bottom/top) position. The
blind will step up and down once to confirm that your end position has been removed. You are
now able to set a new (bottom/top) position.
Adjust your end positions
To adjust one of your end positions you need to place your blind at the end position
you want to adjust. Pull and wait until the blind has reached the end position you want
to adjust.

9
11
12
Move your blind to the new (bottom) position
Pull and hold the chain until the blind has reached the bottom position.If the blind
moves in the opposite direction, release the chain and pull and hold again.
Adjust until the desired bottom position has been reached.
Save your (bottom) position
When your blind is positioned at your bottom position hold the button until the blind moves up
and down to save your bottom position.
ENGLISH

10
14
13
5 s
7 s
Control your blind to favorite position
When your blind is not positioned at the favorite position hold the pull for 5 seconds and your
blind will move to it’s favorite position.
Save the favorite position
When there is no favorite position programmed you need to position your blind at your
favorite position. When the blind is at your favorite position hold the pull until the blind
steps up and down once .(Approximately 7 seconds)