MOTION BLINDS Honeycomb User manual

User Manual EN
Motionblinds Manual
Honeycomb
Motor CM-08-E

2
Con
forms to
UL Std. 325
Cleaning
Follow these general rules when cleaning the
outside of the device and its components:
Use a damp, soft, lint-free cloth. Avoid getting
moisture in openings.
Do not use aerosol sprays, solvents, alcohol, or
abrasives.
Service & Support
Do not perform repairs yourself. Do not attempt to
open the device or disassemble it. You run the risk
of electric shock and voiding the limited warranty.
No user-serviceable parts are inside.
Warranty Service
First follow the advice in this manual. If the product
appears to be damaged or does not function
properly, go to your local dealer for instructions on
how to obtain warranty service.
Recycle
This marking indicates that this product should
not be disposed with other household wastes
throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources. To
return your used device, please use the return and
collec-tion systems or contact the retailer where
the product was purchased. They can take this
product for environmental safe recycling.
Read the instructions carefully
before assembling and using
the product. Assembly can be
completed by non-professionals.
For indoor use only.
Young children can strangle
themselves with the loop of
pull cords, chains and tapes,
and cords that operate window
coverings.
To avoid strangulation and
entanglement, keep cords out
of reach of young children.
Cords may ensnare a child’s
neck.
Move beds, cots and furniture
away from window covering
cords.
Do not tie cords together.
Make sure cords do not twist
together and form a loop.
WARNING

3
Buttons and functions
USB-C charging port
USB-C connected
LED (Battery/Reset indicator)
Reset/Program button
Pull control
End position button
When a USB-C cable is connected and powered, the functions of the reset/program button
automatically changes, allowing to set end positions with this button. As long as the USB-C is
connected and powered the default reset/program functions can not be used.
Program Modes
ENGLISH

4
1
ABSOLUTE HONEYCOMB
max. 750 mm / 29.53 in
max.75 mm
2.95 in max.75 mm
2.95 in
Inside mount
Outside mount
INSTALLATIONMANUAL
INST_PLC38-B10_R0_GB0
WARNING
Installation PLC38-B10
Read the instructions carefully before assembling and using the product.
Assembling process can be completed by non-professionals. For indoor use only.
●Young children can strangle in the loop of pull cords, chains and tapes,
and cords that operate window coverings.
●To avoid strangulation and entanglement,
keep cords out of the reach of young children.
Cords may become wrapped around a child’s neck
●Move beds, cots and furniture away from window covering cords.
●Do not tie cords together.
Make sure cords do not twist together and form a loop.
1
2
1
ABSOLUTE HONEYCOMB
max. 750 mm / 29.53 in
max.75 mm
2.95 in max.75 mm
2.95 in
Inside mount
Outside mount
INSTALLATIONMANUAL
INST_PLC38-B10_R0_GB0
WARNING
Installation PLC38-B10
Read the instructions carefully before assembling and using the product.
Assembling process can be completed by non-professionals. For indoor use only.
●Young children can strangle in the loop of pull cords, chains and tapes,
and cords that operate window coverings.
●To avoid strangulation and entanglement,
keep cords out of the reach of young children.
Cords may become wrapped around a child’s neck
●Move beds, cots and furniture away from window covering cords.
●Do not tie cords together.
Make sure cords do not twist together and form a loop.
Install the blind
Activate the blind
Follow the steps in the installation instructions to install the blind.
To activate the blind, connect it to a standard USB-C 5V power supply via a USB-C cable.
This can be your iPhone’s power adapter, for example.

5
1234-567-8901
1234-567-8901 1234-567-8901
3
4
Add Eve MotionBlinds to your platform
Add Eve MotionBlinds to the platform of your choice and make sure to
have a compatible Thread Border Router.
More information : motionblinds.com/eve/matter
Now you can easily add Eve MotionBlinds to your smart home in just a few steps by scanning
the Matter Setup Code using the app of your favorite platform. Scan the Matter Setup Code
to add it your platform.
Eve MotionBlinds needs end positions to work properly. End positions can be programmed in
two ways. In the Eve app or by the end position programming button on your blind. (Step 5)
After scanning you can hide your Matter Setup Code.
Setup the blind
ENGLISH

6
6
5
1
2
Set end positions
Beside setting the end positions by the app you are able to set the end positions by pressing the
button on the motor. 1: To enter this program mode make sure the USB-C cable is connected and
powered (see page3). 2: Pull and hold the chain until the blind has reached the bottom position.
If the blind moves in the opposite direction, release the chain and pull and hold again.
Adjust until the desired bottom position has been reached.
Save your bottom position
When your blind is positioned at your bottom position hold the button until the blind moves up
and down to save your bottom position.

7
8
7Move your blind to the top position
Save your top position
Pull and hold the chain until the blind has reached the top position.
WARNING: risk of damage. Slowly approach the top position. If the blind moves in
the opposite direction, release the chain and pull and hold again.
Adjust until the desired top position has been reached.
When your blind is positioned at your top position hold the button until the blind moves up
and down to save your top position.
ENGLISH

8
3 s
10
9
Remove your (bottom/top) position
Hold the end position program button for 3 seconds to remove your (bottom/top) position. The
blind will step up and down once to confirm that your end position has been removed. You are
now able to set a new (bottom/top) position.
Adjust your end positions
To adjust one of your end positions you need to place your blind at the end position
you want to adjust. Pull and wait until the blind has reached the end position you want
to adjust.

9
11
12
Move your blind to the new (bottom) position
Pull and hold the chain until the blind has reached the bottom position.If the blind
moves in the opposite direction, release the chain and pull and hold again.
Adjust until the desired bottom position has been reached.
Save your (bottom) position
When your blind is positioned at your bottom position hold the button until the blind moves up
and down to save your bottom position.
ENGLISH

10
14
13
7 s
5 s
Control your blind to favorite position
When your blind is not positioned at the favorite position hold the pull for 5 seconds and your
blind will move to it’s favorite position.
Save the favorite position
When there is no favorite position programmed you need to position your blind at your
favorite position. When the blind is at your favorite position hold the pull until the blind
steps up and down once .(Approximately 7 seconds)

11
15
7 s
2 x
Save a new favorite position
To remove your previous favorite position you need to place your blind at
your current favorite position. (Step 14) Then Hold the pull until the blind
steps up and down once. (Approximately 7 seconds) Your favorite position
is now removed. Follow step 13 to set your new favorite position.
Change direction of rotation
If the position of the blind in the app is opposite to your blind, change the direction of rotation
by pressing the End Position button twice within one second.
ENGLISH

12
LED light flashes
red during operation;
Charge the battery
LED light flashes
green; battery is
charging
LED light constantly
green; battery is fully
charged
Recharge the blind
To charge the blind, connect it to a standard USB-C 5V power supply via a USB-C cable.
This can be your smartphones power adapter, for example. Charge at least once a year.

13
Important Safety instructions
WARNING: To reduce the risk of severe injury or
death, it is important to follow these instructions
for personal safety. Save these instructions.
Read and follow all installation instructions.
This appliance can be used by children aged
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use
of the appliance in a safe way and understand
the hazards involved. Children should not
play with the appliance. Cleaning and user
maintenance should not be performed by
children without supervision.
Do not allow children to play with fixed controls.
Keep remote controls away from children.
Frequently examine the installation for
imbalance and signs of wear or damage to
cables and springs. Do not use if repair or
adjustment is necessary.
This instruction manual is also available on the
website.
The drive must be disconnected from its power
source during cleaning, maintenance and when
replacing parts.
The A-weighted emission sound pressure level
of the drive is equal to or less than 70dB(A).
Indoor and household use only.
Disconnect the drive from the power supply
or switch off the automatic controls when
maintenance, such as window cleaning, is
being carried out in the vicinity.
When operating a biased switch, make sure that
other persons are kept away.
Do not operate when maintenance, such as
window cleaning, is being carried out in the
vicinity.
The tube motor must only be supplied with safety
extra low voltage corresponding to the marking
on the appliance.
Maximum operating temperature of motor is
+55°C.Maximum charging temperature of
battery pack is +45°C.
This appliance contains batteries that are non-
replaceable.
Important Installation instructions
WARNING: Important safety instructions. Follow all
instructions, since incorrect installation can lead
to severe injury.
This motor can only be used with soft material
for driven parts.
Hazardous unprotected moving parts of the
drive must be installed higher than 2.5m above
the floor or any other level surface that could
provide access to it.
Install the actuating member of a manual
release at a height less than 1.8m.
The actuating member of a biased switch is to
be located within direct sight of the driven part
but away from moving parts. It is to be installed
at a minimum height of 1.5m and not accessible
to the public.
The mass and the dimension of the driven part
must be compatible with the rated torque and
rated operating time.
Fixed controls have to be clearly visible after
installation.
The driven part must be compatible with the
rated torque 0.6N.m and rated operating time
(12 min).
The drive is intended to be installed at a height
of at least 2.5m above the floor or any other
accessible level surface.
All-pole disconnection switches must be
incorporated in the fixed wiring in accordance
with the wiring rules.
The appliance must only be supplied at safety
extra low voltage corresponding to the marking
on the appliance.
Before installing the drive, remove any
unnecessary cords or components and disable
any equipment not needed for powered
operation.
ENGLISH

14
FCC Manual | FCC ID: ZY4CM08E
IC:28177-CM08E
Regulatory Information
1 FCC Information for User
This product does not contain any user
serviceable components and is to be used with
approved antennas only. Any product changes
or modifications will invalidate all applicable
regulatory certifications and approvals.
2 FCC Electronic Emission Notices
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two
conditions:
1. This device may not cause harmful interference
2. This device must accept any interference
received, including interference that may cause
undesired operation.
3 FCC Radio Frequency Interference
statement
This equipment has been tested and found to
comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications.
Operation of this equipment in a residential area
may cause harmful interference, in which case the
user will be required to correct the interference
at their own expense. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna
Increase the distance separating the equipment
and receiver
Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV
technician for help
To satisfy FCC / IC RF exposure requirements,
a separation distance of 20 cm or more should be
maintained between the antenna of this device
and persons during device operation.To ensure
compliance, operations at closer than this
distance is not recommended.
EU Declaration
Hereby, Coulisse declares that the radio
equipment type CM-08-E is in compliance
whith directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the
following internet address: support.motionblinds.
com
Frequency range: 433 MHz, RF power: 2.32 dBm
Frequency range BLE: 2402 - 2480 MHz,
RF power: 3 dBm EIRP
Frequency range Thread: 2405 - 2480 MHz,
RF power: < 20 dBm EIRP
ISED Compliance
Thisdevicecontainslicence-exempttransmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’ s licence-exempt
RSS(s). Operation is subject to the following two
conditions: This device may not cause interference.
This device must accept any interference, including
interference that may cause undesired operation
of the device.

15
5 s
1-3
+20 s
5 x
10 s
5 x
Reset the connection
Change motor speed / sound level
Hold the program button for 10 seconds to delete the connection between the blind and the app.
The LED lights up 5 times and the blind steps up and down 1 time to indicate that the connection is
reset. Now the blind can be reconnected.
Hold the program button for 5 seconds to change the motor speed / sound level. The blind steps up
and down 1 time to indicate that the speed has been adjusted to 1 of the 3 levels. Warning: release
the button after 5 seconds when the blind steps up and down to avoid resetting the connection.
Reset the blind
Resetting the blind results in deleting the end positions and connections of the blind with apps
and remote controls. Shortly press the program button to activate program mode. The blind will
start stepping up and down.Hold the reset/program button for at least 20 seconds to reset the
blind. The blind will stop stepping twice. After the second stop, the blind will give one extra step
to indicate that is has been reset.
ENGLISH
Short press
WARNING: Make sure the USB-C cable is removed. Otherwise you will delete the end limits.
WARNING: Make sure the USB-C cable is removed. Otherwise you will delete the end limits.
WARNING: Make sure the USB-C cable is removed. Otherwise you will delete the end limits.

16

17
Remote programming

18
.1
.2
.3
2
.1
.2
1Pair a remote control
Any MotionBlinds remote can be connected to your blind.
Select a channel on the remote and press the program button on the motor to activate program mode.
The blind will start stepping up and down.
Press the pair button on the back of the remote control to pair the blind with the selected channel.The
blind will shortly stop stepping, indicating that the remote has been paired to the blind.
Shortly press the program button to deactivate program mode. The blind stops stepping and can be
operated.
Shortly press the down button to check if the blind unrolls the right way. If the blind moves up, the
rotational direction must be changed.
Simultaneously press the up and down button to change the rotational direction.
Up
Down
Pair
button
Pair
button
CM-11
CM-12
CM-13 CM-15
Pair
button
CM-17
Check rotational direction
WARNING: risk of damage. Stop the blind before reaching the end positions.

19
3
4Save bottom position
Down
Up
Centre
Simultaneously hold the centre and the up button until the blind stops
stepping and starts stepping again. The bottom position has been
saved.
Set bottom position
Press and hold the down button until the blind reaches the desired
bottom position. WARNING: risk of damage. Slowly approach the bottom
position.
ENGLISH

20
6
5Set top position
Press and hold the up button until the blind reaches the desired top position.
WARNING: risk of damage. Slowly approach the top position.
Simultaneously hold the centre and the down button until the blind stops stepping and starts
stepping again. The top position has been saved.
Up
Save top position
Down
Centre