Motorola solutions Edesix videobadge vb-400 User manual

QUICKSTART GUIDE | VB400 1

VB400

BODY-WORN

CAMERA

QUICKSTART GUIDE

QUICKSTART GUIDE | VB400 2

TABLE OF CONTENTS

INTRODUCTION 3

HOW TO CHARGE YOUR VB400 4

CHARGING WITH A 1-PORT DOCK 5

CHARGING WITH A 14-PORT DOCK 6

BATTERY STATUS LED 7

CONFIGURING YOUR VB400 8

IDENTIFYING AN RFID ASSIGNED VB400 9

USING YOUR VB400 10

TO START / STOP RECORDING 10

WEARING YOUR VB400 12

ACCESSORIES 13

REGULATORY INFORMATION 14

QUICKSTART GUIDE | VB400 3

INTRODUCTION

Thank you for choosing the VB400 Body-worn camera. This simple guide will lead you through the set up and use of your VB400.

Lens

Buzzer Speaker

Function

Button A

LED

Function

Button C

Slider

Dual

Microphone

Front

Function Button

Function

Button B

LED

QUICKSTART GUIDE | VB400 4

HOW TO CHARGE YOUR VB400

Upon receiving your VB400, it is recommended that you fully charge the device before usage.

When charging using a 1-Port Dock or 14-Port Dock, insert the camera into the slots as shown below, ensuring the camera clicks securely in place.

Check that the top LED blinks green to indicate charging.

Slide down to

click into place

QUICKSTART GUIDE | VB400 5

CHARGING WITH A 1-PORT DOCK

(VB-400-DOCK-SOLO)

Connected to your laptop or DockController.

If you are charging your VB400 camera via a 1-Port Dock

(VB-400-DOCK-SOLO) your camera will bleep to indicate charging has

commenced, and the LED, as indicated, will ﬂash green to show charging.

Charging: Flashing green LED Fully Charged: Solid green LED

Once fully charged, the same LED will turn solid green. If the LED is not lit, the device is not charging. Your VB400 will be fully charged within 8 hours

from a ﬂat battery.

QUICKSTART GUIDE | VB400 6

CHARGING WITH A 14-PORT DOCK

(VB-400-DOCK-14/US)

Connected to a power supply and DockController

If you are charging your VB400 camera via a 14-Port Dock (VB-400-DOCK-14/US)

the top LED will ﬂash green to show charging, and the camera will bleep when

successfully connected to VideoManager.

Once fully charged, the same LED will turn solid green. If the LED is not lit, the device is not charging. Your VB400 will be fully charged within 8 hours

from a ﬂat battery.

Charging: Flashing green LED Fully Charged: Solid green LED

QUICKSTART GUIDE | VB400 7

BATTERY STATUS LED

To quickly understand the current battery status of your VB400, press the bottom button on the front face of the camera and refer to the bottom LED.

COLOR KEY:

Green LED: OK

Orange/Yellow LED: Low

Red LED: Critical

Battery Status Button

(Conﬁgurable)

QUICKSTART GUIDE | VB400 8

CONFIGURING YOUR VB400

Prior to using your VB400, your device must be conﬁgured and assigned to you

using VideoManager. For detailed information on how to conﬁgure your device,

please refer to the VideoManager User Guide.

Each VB400 requires a valid VideoManager License, in order for you to assign

devices and access footage. For further details, see the VideoManager User

Guide.

To ascertain whether your VB400 has been conﬁgured, please view the top LED

on your device. This LED will turn solid green once conﬁgured and assigned.

Your VB400 is charged, assigned and ready to use when the LEDs shown are

both solid green.

Conﬁgured, charged &

assigned Solid green light

PLEASE NOTE: If you try to use your VB400 before it has been assigned, the bottom LED on the front face of the camera will start to ﬂash red and you

will hear an alarm tone. You will not be able to use your camera until it has been assigned.

QUICKSTART GUIDE | VB400 9

IDENTIFYING AN RFID ASSIGNED VB400

Once your device is conﬁgured, your system administrator may wish camera users to utilize an RFID system for camera assignment. For further

information on assigning VB400s using an RFID reader, please refer to the VideoManager User Guide.

Having presented your RFID card, your docked, assigned VB400 will identify itself with a solid red LED as shown.

RFID

Assigned Camera

RFID Reader

(RF-220)

RFID-Card

(RF-CARD-10)

QUICKSTART GUIDE | VB400 10

USING YOUR VB400

The VB400 series of cameras are intuitive and simple to use.

TO START / STOP RECORDING (CONFIGURABLE)

Users can activate recording by pressing on the single front button located in the center of the camera as shown. Recording is stopped by pressing and

holding the front button.

Record activation and deactivation buttons are conﬁgurable by Administrators.