Motorola RMN5104 User manual

BLUETOOTH ® ADAPTER
RMN5104
EN LAS BP FRC
Wirelesssolution.book Page 1 Monday, November 5, 2007 8:48 PM

Wirelesssolution.book Page 2 Monday, November 5, 2007 8:48 PM

1
English
FOREWORD
Product Safety and RF Exposure
Compliance
ATTENTION!
The radio is restricted to occupational use only to satisfy
FCC RF energy exposure requirements. Before using
this product, read the RF energy awareness information
and operating instructions in the Product Safety and RF
Exposure booklet enclosed with your radio (Motorola
Publication part number 6881095C98) to ensure
compliance with RF energy exposure limits.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received,
including interference that may cause undesired
Any changes or
modificationsBefore using this product, read
the operating instructions for
safe usage contained in the
Product Safety and RF
Exposure booklet enclosed with
your radio.
!
C a u t i o n
Bluetooth® is a registered trademark of the
Bluetooth Special Interest Group.
Wirelesssolution.book Page 1 Monday, November 5, 2007 8:48 PM
operation. Any changes or modifications not expressly
approved by Motorola may void the user's authority to
operate this device.

2
English
DESCRIPTION
The RMN5104 Bluetooth Adapter is an accessory
designed to complement Radio Models PR1500,
XTS 1500, XTS 2500, XTS 5000 and HT1000.
OPERATION
Removing the Radio's Universal
Connector Cover
If the radio's universal connector cover is installed
on the radio, refer to Figure 1 and perform the
following steps:
1. Looking at the antenna side of the radio, insert
a flat blade screwdriver between the lower end
of the universal connector cover and the slot
below the universal connector.
2. Pry upwards on the cover's lower end until it
disengages from the radio.
Figure 1: Removing the radio cover
Wirelesssolution.book Page 2 Monday, November 5, 2007 8:48 PM

3
English
Attaching the Bluetooth Adapter to the
radio's Universal Connector
Ensure that the radio is turned off before attaching
the Bluetooth adapter to the radio. Refer to
“Attaching the Bluetooth Adapter to the radio's
Universal Connector” on page 3 and attach the
adapter to the radio as follows:
1. Inspect the seal of the adapter to ensure that it
is not damaged and is free of contamination.
2. Align the adapter to the radio's universal
connector.
3. Looking at the antenna side of the radio, insert
the bottom hooked end of the adapter into the
bottom slot below the universal connector on
the radio.
4. While holding the adapter seated in the bottom
slot, pivot the top of the adapter towards the
radio, then engage the adapter’s spring loaded
latch in the radio's top slot.
Wirelesssolution.book Page 3 Monday, November 5, 2007 8:48 PM

4
English
5. Secure the adapter to the radio using the
tethered screw.
Figure 2: Attaching the Bluetooth Adapter
to the Radio’s Universal Connector
Top
Slot
Bottom
Slot
Bottom
Hooked End
Screw
Spring
Latch
Wirelesssolution.book Page 4 Monday, November 5, 2007 8:48 PM

5
English
Pairing The Adapter And Headset
1. Turn ON the radio.
2. Place the headset in pairing mode (see
headset manual). Place the adapter in pairing
mode by pressing and holding the adapter PTT
switch for 3 seconds (see Figure 3).
Figure 3: The PTT Switch
3. Determine the adapter mode by observing the
LED:
• The LED blinks rapidly (ON twice per
second) when the adapter is attempting to
pair with the headset.
• The LED blinks slowly (ON once per
LED
Indicator
PTT
Switch
Wirelesssolution.book Page 5 Monday, November 5, 2007 8:48 PM

6
English
second) when the adapter is attempting to
reconnect with the previously paired
headset.
• The LED blinks very slowly (ON once every
4 seconds) when the adapter and headset
are paired.
4. When the adapter and headset pair, the LED
will light for 3 seconds and then blink once
every 4 seconds thereafter. It is recommended
to verify proper pairing by performing an audio
check such as squelch or keypad tone.
5. If the adapter and headset fail to pair within 30
seconds (the LED continues to blink once per
second), then turn them off and repeat Steps 1
to 3.
6. Once the adapter and headset are paired,
received audio is routed to the headset. To
transmit, press the adapter PTT switch and
speak into the headset microphone.
Reconnecting The Adapter and Headset
1. Turn ON the headset.
2. Attach the adapter to the radio.
3. Turn ON the radio.
4. The adapter and headset will automatically
reconnect within 30 seconds. The LED will
blink once every second during this time.
When they reconnect, the LED will light for 3
seconds, then blink once every 4 seconds
thereafter.
Wirelesssolution.book Page 6 Monday, November 5, 2007 8:48 PM

7
English
5. If the adapter and headset do not reconnect
within 30 seconds, then turn them off and
follow the steps under “Pairing The Adapter
And Headset” on page 5.
Lost Bluetooth Link
In the presence of interference, or if the radio and
adapter are out of range of the paired headset, it is
possible that the Bluetooth link between the
adapter and headset may be dropped. In this
case, received audio will be routed back to the
radio, and the radio's microphone will be active.
The adapter will attempt to reconnect to the
headset for 15 seconds. After this time, to
reestablish the Bluetooth link, it will be necessary
to repeat the process of “Pairing The Adapter And
Headset” on page 5.
Wirelesssolution.book Page 7 Monday, November 5, 2007 8:48 PM

8
English
Audio Routing Toggle Switch
The toggle switch on top of the adapter allows the
user to switch audio between the Bluetooth
adapter and the radio.
Figure 4: Audio Routing Toggle Switch
• With the toggle switch positioned away from
the radio, audio will be routed to the radio
speaker, and the radio microphone is active
during transmit.
• With the toggle switch positioned towards
the radio, audio will be routed to the
Bluetooth headset ear piece, and the
headset microphone will be active. The
LED
Indicator
Toggle
Switch
Wirelesssolution.book Page 8 Monday, November 5, 2007 8:48 PM