Motorola Avigilon AVA QUAD CAMERA Installation instructions manual

AVA QUAD CAMERA
MOUNTING GUIDE
Avigilon Alta Cloud Security
MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA

MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA 2 / 17
IMPORTANT WARNINGS AND SAFETY INSTRUCTIONS
Avoid exposing the camera to shocks, high pressure or
temperatures above 60°C.
Avoid placing the camera near fans, ventilation or other noise
sources. This will degrade audio performance.
Avoid scratching or leaving fingerprints on the lens cover,
this degrades image quality. If possible, keep the protective
plastic on the lens cover during installation.
Do not clean the camera with harsh detergents, gasoline or
chemicals such as acetone.
Do not try to repair the unit yourself. Refer all servicing of the
camera to Avigilon or contact a reseller.
Do not install the camera during rain, mist or other conditions
of high humidity. Water may be trapped inside, causing
damage or condensation issues.
Disconnect power from the unit when performing a
maintenance task.
The power supply should bear the UL listed and LPS marks.
Requires PoE+ power connection to operate with IR.
This product should be supplied by a Power over Ethernet
Power Sourcing Equipment (PSE) compliant to IEEE 802.3at
Type 2 (PoE+).
The camera should be connected only to PoE networks
without routing to the outside plant. The PoE PSE must be
properly grounded.
Please contact Avigilon’s certified dealers (or distributor) for
power adapters.
For the grounding wire use a green/yellow wire (min. 18AWG),
a knurled washer and min. 3.5mm screw.

MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA 3 / 17
OVERVIEW
Outer view
Release button IR LEDs
Threaded holes for
mounting adapter
Top mounting plate
Through holes for ceiling-mount
or wall mount bracket
Dome cover
Top view
PACKAGE CONTAINS
Quad camera
IR light cover
Alignment sticker
Screws and anchors
T10 security L-key

MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA 4 / 17
OVERVIEW
Inner view
Lens (sensor) module,
3-axis adjustable
Reset button
Cable gland
Status LEDs
Safety tether wire
RJ45 Ethernet port
(only POE+ supported)

MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA 5 / 17
A
C
B
T10 security
bit
1 2 3
A
B
C
PREPARING TO MOUNT THE CAMERA
For all install options

MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA 6 / 17
PREPARING TO MOUNT THE CAMERA

MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA 7 / 17
A1
OPTION A - USING THE CEILING MOUNT
Cable hole
Cable hole
Drill hole
Drill hole
Drill hole
180mm
Alignment sticker
A2

MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA 8 / 17
OPTION B - USING THE IN-CEILING MOUNT
B1
If needed, add hanging rods to strengthen the ceiling structure.
Weight of camera: 2.7 Kg
Weight of Recessed kit: 1.1 Kg
Hanging rod
Main keel
Secondary keel
ø15cm
Cut a hole in the center of the tile with a diameter of 15cm.

MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA 9 / 17
OPTION B - USING THE IN-CEILING MOUNT
B2
Remove the assembly from the ceiling and assemble the adapter plate to the bracket rod.
Use nuts, washers and lock washers as shown, tighten the nut towards the adapter plate and
make sure the two nuts close to the bracket rod are loose.
Assemble the bracket stand to the bracket rod, adjust the width so the stands are resting on the
secondary keels. Secure the position by the two flathead screws.
Adapter plate
Bracket rod
Bracket stand
B3

MOUNTING GUIDE | AVIGILON AVA QUAD CAMERA 10 / 17
OPTION B - USING THE IN-CEILING MOUNT
B4 B5
Put the bracket assembly in the correct position in the ceiling and install the tile.
Assemble the camera top mounting plate to the adapter plate, adjust the position so the camera
will be flush to the ceiling and the release button can be pressed.
Fasten the remaining two nuts to secure position of the rod.
Required:
ACQ-REC-KIT Recessed kit