Motorola CT2 User manual

Model: CT2
Corded Telephone

Welcome...
to your new Motorola CT2 Corded Telephone!
• Recall for network functions.
• Hold facility to put your caller on hold and listen to music.
• Redial the last number dialled at the touch of a button.
• Repeat call symbol to alert you if you missed a call from the same number more than
once.
• Redial at least 5 dialled numbers for easy dialling.
• 10 two-touch memory numbers for easy dialling.
• Tone and Pulse dialling.
• Ringer and hands-free volume control.
• Speakerphone for hands-free conversations.
• Time and date function.
• Caller ID shows you the number of who is calling and stores the number of at least the
last 32 callers in a Calls list.1
• Call Timer the display will automatically time the duration of all external calls.
Your CT2 uses dynamic software in the redial and received calls list, if the phone
numbers in the list have less than 16 digits then the number of entries stored in the
received calls list is increased.
Need help?
If you have any problems setting up or using your CT2, please contact Customer
Services on (65) 68412668.
Email: [email protected]om.sg
Alternatively, you may nd the answer in the ‘Help’ section at the back of this guide.
1You must subscribe to your network provider’s Caller ID or Call Waiting service for
these features to work. A subscription fee may be payable.

ECOMOTO: a convergence of eorts by marketing, design, research, engineering
and supply chain management that leads to better products for everyone. A holistic
view that focuses on both social and environmental responsibility.
A passion and a shared point of view.
The right thing to do.
• Meets and/or exceeds EMEA environmental regulatory requirements.
• Eco friendly packaging with a minimum 20% post consumer recycled content.
• Phone housing is built with a minimum of 25% post consumer recycled content plastic.
This user guide provides you with all the information you need to get the
most from your phone.
To set up your phone, follow the simple instructions in ‘Getting Started’,
on the next few pages.
IMPORTANT
Only use the telephone line cord supplied.
Got everything?
• Corded handset and curly cord
• Corded base
• Telephone line cord

4
1. Getting started .....................................................................6
2. Getting to know your phone ................................................8
3. Using the phone .................................................................11
3.1 Calls ...............................................................................................................11
3.1.1 Make a call ..........................................................................................11
3.1.2 Pre-dial ................................................................................................11
3.1.3 End a call ............................................................................................11
3.1.4 Receive a call ......................................................................................11
3.2 Hold................................................................................................................11
3.3 Redial .............................................................................................................12
3.4 Open the Redial list .......................................................................................12
3.5 Dial a number from the Redial list .................................................................12
4. Memory ..............................................................................13
4.1 Store a two-touch memory number..............................................................13
4.2 Store a two-touch memory number from the calls list..................................13
4.3 Dial a two-touch memory number with the handset lifted...........................13
4.4 Dial a two-touch memory number over the loudspeaker.............................13
4.5 Check and delete a memory number ..........................................................13
5. Date and time .....................................................................14
5.1 Set the date and time.....................................................................................14
6. Area Code ..........................................................................15
6.1 Store the area code .......................................................................................15
7. PABX access code ..............................................................16
7.1 Store the PABX access code..........................................................................16
8. Display ................................................................................17
8.1 Change the display contrast .........................................................................17
9. Recall and dial mode..........................................................18
9.1 Change your dial mode.................................................................................18
10. Calls lists .............................................................................19
10.1 Open the Received calls list..........................................................................19
10.2 Dial a number from the Received calls list ....................................................19
10.3 Open the Missed calls list..............................................................................19
10.4 Dial a number from the Missed calls list ........................................................19

5
11. Help.....................................................................................20
12. General information ...........................................................21
13. Wall mounting ....................................................................25

6 Getting started
1. Getting started
IMPORTANT
Do not place your CT2 in the bathroom or other humid areas.
Location
You need to place your CT2 base within 2 metres of the telephone wall socket so that the
cable will reach. The socket-outlet shall be installed near the equipment and shall be easily
accessible.
If you are wall mounting your phone please refer to the wall mount template on page 25.
Connecting the handset and base
1. Plug one end of the handset curly cord into the socket marked on the underside of
the base and the other end into the socket at the bottom of the handset.
2. Plug the telephone line cord into the socket marked .

7Getting started
Overview of your handset
A Earpiece
To listen to your caller.
B Microphone
To speak to your caller.
C Curly cord socket
Where you plug in your curly cord.
A
B
C

8 Getting to know your phone
2. Getting to know your phone
Overview of the base
A Hook switch
Hangs up a call when pressed or when you replace the handset.
B Handset hook
Rotate to secure the handset in wall mount mode.
C Pause
When dialling or storing a number press to enter a pause (P).
P
Menu
Memory
Hold
R1
R2
A
B
C
D
E
F
G
H
I
J
K
L
M
O
P
Q
R
N

9Getting to know your phone
D Down
Press to scroll down through the menu.
In standby mode press to open the missed calls list.
E Hold
Press to put your caller on hold.
F R2 Long Recall (600ms)
To be used with certain network services.
When on an external call, press to access a Call Waiting Line when a call waiting
prompt signal is heard. Press again to toggle between the two calls.
G Display
See page 10 for an overview of display icons.
H Up
Press to scroll up through the menu.
In standby mode press to open the calls list.
I Redial
Press to view last number dialled out and continue pressing to scroll through the 5
stored numbers.
J Delete
Press to delete an incorrect number or go back in the menu.
K Menu
Press to open the menu or conrm a menu option.
L New missed call indicator / Ring indicator
Flashes when you have new missed calls and when the phone is ringing.
M Memory
Dial out two-touch memory numbers.
N R1 Short Recall (100ms)
To be used with certain network services.
O Ring indicator
Flashes to indicate the phone is ringing.
P Last number redial
Press to redial the last number dialled.
Q Hands-free
Activate and deactivate the hands-free during / when making a call.
R Ringer switch
Switch the ringer volume from high ( ) to low ( ).
NOTE
The ringer volume cannot be set to OFF.

10 Getting to know your phone
Display
Indicates when you are viewing the missed calls list.1
Indicates when you are viewing the received calls list.1
Indicates when you are viewing the redial list.
Flashes when you have received a new call.
Indicates when you have more than 1 missed call from the
viewed number.
Indicates when you have a voicemail waiting.2
1For this feature to work, you must subscribe to Caller ID Service from your network
operator. A subscription fee may be payable.
2This feature is dependent on your Network Service provider supporting the service.

11Using the phone
3. Using the phone
3.1 Calls
3.1.1 Make a call
Lift the handset, when you hear the dial tone, dial the number.
3.1.2 Pre-dial
1. Enter the phone number (maximum 32 digits). If you make a mistake press D. Lift
the handset to dial the number.
2. Press hto dial the phone number over hands-free.
NOTE
You can also make calls using the two touch memory keys, see page 13.
3.1.3 End a call
1. Place the handset back on the base.
Or:
2. Press hto end a hands-free call.
3.1.4 Receive a call
1. Lift the handset to answer the call.
Or:
2. Press hto answer the call in hands-free.
NOTE
If during a call you want to activate hands-free, press hand hang up the handset.
To change the ringer volume from high ( ) to low ( ) use the switch on the side of the
base.
3.2 Hold
You can place your caller on hold so that you and your caller hear hold music.
1. During a call, press Hand you and your caller will hear hold music.
2. Press Hagain to resume your call.
NOTE
If His pressed when not on a call a beep will be heard, but it will have no eect on the
functions of the phone.

12 Using the phone
3.3 Redial
The last number dialled is stored in the phone; this can be up to 32 digits long.
1. Pick up the handset and press r.
Or:
2. Press hand then r.
3.4 Open the Redial list
The last 5 entries dialled are stored in the phone; these can be up to 16 digits long.
1. Press Rto open the Redial list.
2. Continue pressing to scroll through the list.
3.5 Dial a number from the Redial list
1. Press Rto open the Redial list.
2. Continue pressing Rto scroll to the entry you want.
3. Lift the handset or press hto dial the displayed entry.

13Memory
4. Memory
You can store ten telephone numbers in the two touch memory; the numbers can be up to
16 digits long.
4.1 Store a two-touch memory number
1. Dial the number to be stored.
2. Press m.
3. Press one of the numbers on the keypad 0-9, the number is stored.
4.2 Store a two-touch memory number from the calls list
1. Press uto open the received or dto open the missed calls list.
2. Scroll uor dto required number.
3. Press m.
4. Press one of the numbers on the keypad 0-9.
4.3 Dial a two-touch memory number with the handset lifted
1. Lift the handset.
2. Press M.
3. Press one of the keypad buttons 0-9.
4. The memory number will be dialled.
4.4 Dial a two-touch memory number over the hands-free
1. Press M.
2. Press one of the keypad buttons 0-9.
3. The memory number will dial out automatically.
4.5 Check and delete a memory number
1. Press M.
2. Press and hold the relevant keypad number 0 - 9 for 3 seconds.
3. The memory number will be displayed.
4. Press Dto delete the memory number.
NOTE
Remember to make a note of your memory numbers for easy reference.

14 Date and time
5. Date and time
If you have subscribed to a FSK type Caller ID Service, the date and time is set
automatically when you receive your rst call.
If you do not have a FSK Caller ID service, you can set the date and time manually.
5.1 Set the date and time
1. Press m, the display shows SEt 1 dAtE .
2. Press mto select.
3. The year will flash; scroll uor dto the correct year and press mto conrm.
4. Repeat this procedure for the month, day and time settings.
5. Press Dto exit.

15Area Code
6. Area Code
You can set your local area code into the phone. When a number from that area code calls
only the local number will be displayed and stored.
6.1 Store the area code
1. Press m, the display shows SEt 1 dAtE .
2. Scroll uor dto
SEt 2 CodE .
3. Press m, the display shows
CodE - - - - - .
4. The rst
- is flashing, press uor dto scroll to the correct digit.
5. Press mto conrm.
6. Repeat this procedure until the full code is entered.

16 PABX access code
7. PABX access code
If the CT2 is connected to a switchboard, you may need to enter a one-digit access code
in the dialling sequence to be able to connect to the outside line.
The access code will be displayed at the beginning of a number on the screen.
7.1 Store the PABX access code
1. Press m, the display shows SEt 1 dAtE .
2. Scroll uor dto
SEt 3 PCOdE .
3. Press m, the display shows
PCOdE - .
4. Press uor dto scroll to the correct digit from
0 - 9 .
5. Press mto conrm.

17Display
8. Display
You can change the contrast of the display; there are 5 levels to choose from.
8.1 Change the display contrast
Either:
1. Press m, the display shows
SEt 1 dAtE .
2. Scroll uor dto
SEt 4 lcd .
1. Press m, the display shows
LCd and the current contrast level.
2. Scroll uor duntil you see the contrast you require.
3. Press mto conrm.
Or:
1. Press 2, the display shows
LCd and the current contrast level (1-5) .
2. Continue pressing 2until you see the contrast you require.
3. Press Dto exit.

18 Recall and dial mode
9. Recall and dial mode
Recall is useful to access certain network services and PABX /switchboard services. Your
CT2 has 2 recall buttons 1is the short flash time and 2is for long flash time.
NOTE
1Short flash is 100ms / 2Long Flash is 600ms.
Flash keys are used to refresh a dial tone. When on an external call, press R2 to access
a Call Waiting Line when a call waiting prompt signal is heard. Press again to toggle
between the two calls.
For more information about network services contact your network operator.
Your phone is set to tone dialling. You should only need to change this if connected to an
older type of switchboard / PABX which requires pulse dialling.
9.1 Change your dial mode
1. Press m, the display shows SEt 1 dAtE .
2. Scroll uor dto
SEt 5 P_t .
3. Press mand the display shows the current setting.
4. Scroll uor dto the change the setting.
5. Press Dto exit.

19Calls lists
10. Calls lists
If you have subscribed to a Caller ID service, and provided the identity of the caller is not
withheld, the number of the caller will be displayed together with the date and time of the
call (if provided by the network). When the list is full and a new call is received, the oldest
entry will be deleted automatically.
You can store at least 32 numbers in the received calls list and each number can be up to
16 digits long.
NOTE
If you receive a private call
---P--- will show on the display.
If you receive an out of area call
---O--- will show on the display.
If you receive an error call
---E--- will show on the display.
10.1 Open the Received calls list
1. Press uto open the Received calls list.
2. Continue pressing uto scroll through the list.
3. The display will show
--E n d-- when you reach the end of the list.
10.2 Dial a number from the Received calls list
1. Press uto open the Received calls list.
2. Continue pressing uto scroll to the number you want to dial.
3. Either lift the handset to dial automatically, or press hto dial over hands-free.
10.3 Open the Missed calls list
1. Press dto open the Missed calls list.
2. Continue pressing dto scroll through the list.
3. The display will show
--E n d-- when you reach the end of the list.
10.4 Dial a number from the Missed calls list
1. Press dto open the Missed calls list.
2. Continue pressing dto scroll to the number you want to dial.
3. Either lift the handset to dial automatically, or press hto dial over hands-free.
NOTE
If you have missed calls the LED on the base will flash.
If you have more than one missed call from the same number , will show on the
display when you view the missed calls list.

20 Help
11. Help
No dial tone
• Use only the telephone line cord supplied.
• Check that the telephone line cord is connected properly.
Storing numbers
• Once you have stored a number there is no conrmation tone, you can just hang up
the handset.
• Please remember to make a note of memory numbers for easy reference.