Motorola T325 User manual

Quick Start Guide
motorola T325

1
congratulations
The Motorola T325 Portable Bluetooth® Handsfree Car
Kit Speakerphone gives you the freedom to make and
receive phone calls in your vehicle while safely keeping
your hands on the steering wheel using:
• caller name identification
• automatic power on and off when you enter or leave
your vehicle
• direct access to the favorite contacts you use most
frequently while in your vehicle.
Caution: Please read the important Legal & Safety
information at the back of this guide.
Note: Using a mobile device while driving may cause
distraction. End a call if you can’t concentrate on driving.
Also, using a mobile device or accessory may be
prohibited or restricted in certain areas. Always obey the
laws and regulations on the use of these products.

your speakerphone
2
your speakerphone
Take a moment to familiarize yourself with your new
T325 speakerphone.
Call
Button Indicator
Light Power
Switch
Mute/
Favorite Contacts
Button
Volume Down
Button
Volume Up
Button
Speaker
Charging
Port
Microphone

charge it
3
charge it
You’ll need to charge your speakerphone before using it.
The indicator light is red while the battery is charging.
When the battery is fully charged, the indicator light turns
blue.
Note: Speakerphone is functional while charging.
Note: Your battery is designed to last the life of your
product. It should only be removed by a recycling facility.
Any attempt to remove or replace your battery will
damage your speakerphone.

connect wirelessly
4
connect wirelessly
pair & connect
Let’s get your speakerphone paired and connected to
your Bluetoothenabled phone.
1 Turn off any Bluetooth devices previously paired
(linked) with your speakerphone.
2 Turn off any Bluetooth devices previously paired
(linked) with your phone.
3 Turn on the Bluetooth feature on your phone.
4 Turn on your speakerphone (see page 8).
The indicator light becomes steadily lit in blue.
5 Set your phone to search for Bluetooth devices.
6 Select Motorola T325 from the search results on
your phone.
7 Select Ok or Ye s to pair your speakerphone with
your phone.
Note: When prompted for the passkey, enter 0000 .
When your speakerphone successfully pairs and
connects with your phone, you hear “connected to
<phone name>” and you see the indicator light rapidly
flash in blue and purple.

connect wirelessly
5
download phone contacts
Once paired, your speakerphone automatically
downloads contact names and numbers from your phone
so that it can announce the name of your incoming caller.
Your phone may first request permission to accept
information access. Go ahead and accept so
downloading can begin. Once downloading begins,
you hear “downloading caller ID information”.
The indicator light flashes in purple while downloading.
When your downloading is complete (210 minutes,
depending on number of contacts), you hear “download
complete”.
If the download is interrupted, for example by an
incoming call, it resumes after the call. See page 14 for
steps on manually updating your phonebook (it will not
be updated automatically).
Note: Your phone must support Bluetooth Phone Book
Access Profile (PBAP) for this feature to work.

connect wirelessly
6
reconnect
After initially pairing and connecting your phone and
speakerphone, you don’t need to do it again.
For daily use, make sure your speakerphone is turned on,
and your phone’s Bluetooth feature is on. Your
speakerphone and phone will connect automatically!
test your connection
1 Slide the speakerphone onto your visor (see page 7).
2 On the phone, dial the number and press the
Call/Send key.
If your phone and speakerphone are successfully
connected, you hear ringing on the speakerphone.

install in car
7
install in car
Slide the visor clip onto your sun visor as shown

turn it on & off
8
turn it on & off
You can manually turn your speakerphone on and off or
use the automatic on/off option. The speakerphone may
take up to 4 seconds to power on.
manual on/off
Slide and hold the Power switch to ë until your hear a
tone, then release.
To turn off your speakerphone, slide the Power switch
to
ê . You hear an audio tone when turned off.
Power Off
Position
Power On
Position