Moxa Technologies EDS-G308 Manual

Moxa EtherDevice Switch
EDS-G308
Hardware Installation Guide
Second Edition, April 2009
©2009 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan,
R.O.C.
TEL: [phone]
P/N: 1802003082011

- 2 -
Overview
The EDS-G308 series is equipped with 8 Gigabit Ethernet ports and up to 2
fiber optic ports, making it ideal for applications that demand high bandwidth.
The EDS-G308 series provides an economical solution for your industrial
Gigabit Ethernet connection, and the built-in relay warning function alerts
maintainers when power failures or port breaks occur. The EDS-G308 series
includes 2 models: one with an operating temperature range of 0 to 60°C, and
the other one with an extended operating temperature range of -40 to 75°C.
These 2 models have passed a 100% burn-in test to ensure that they fulfill the
special needs of industrial automation control. The EDS-G308 series can be
easily installed with DIN-Rail mounting as well as distribution boxes.
NOTE Throughout this Hardware Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch:
EDS = Moxa EtherDevice Switch
Package Checklist
Your EDS is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for assistance.
yMoxa EtherDevice™ Switch
yHardware Installation Guide
yMoxa Product Warranty booklet
yProtective caps for unused ports
Features
High Performance Network Switching Technology
y10/100/1000BaseT(X) (RJ45), auto negotiation speed, F/H duplex mode,
and auto MDI/MDI-X connection, 100/1000 BaseSFP slot.
yIEEE 802.3/802.3u/802.3ab/802.3z/802.3x.
yStore and Forward switching process type, 8K MAC address entries.
Industrial Grade Reliablity
yPower failure, port break alarm by relay output
yRedundant dual AC/DC power inputs
Rugged Design
yOperating temperature range of 0 to 60°C, or extended operating
temperature of -40 to 75°C for (-T) models
yIP30, rugged high-strength case
yDIN-Rail or panel mounting ability
yRedundant dual 12/24/48VDC or 18 to 30 VAC at 47 to 63Hz Power
inputs

- 3 -
Panel Layout of
EDS-G308/EDS-G308-2SFP
EDS-G308
Front Panel View EDS-G308-2SFP Front Panel View
6
7
5
2
10
3
4
8
9
1
2
11
12
1
2
14
13
13
Top Panel View
Rear Panel View
ON DIP
12345678
21
1. Grounding screw
2. Terminal block for power input
(PWR1, PWR2) and relay output
3. Power input PWR1 LED
4. Power input PWR2 LED
5. Fault LED
6. TP port’s 10/10/1000 Mbps LED
7. Port number
8. 10/100/1000BaseT(X) Port
9. 100/1000Base SFP slot
10. Model Name
11. DIP switches
12. Heat dissipation orifices
13. Screw hole for wall mounting kit
14. DIN-Rail Kit

- 4 -
Mounting Dimensions (unit = mm)
45.8 45.8
50.4 30.5
18
31.9
44
32.1
18.2
46
46
32.1
18.2
Din-Rail
Panel Mount Kit
134
63.83
86.14
5
6
9.75
66.8
9
30
3.5
3.5
6
M3 M3
M3
M3
M3 M3
DIN-Rail Mounting
The aluminum DIN-rail attachment plate should already be fixed to the back
panel of the EDS when you take it out of the box. If you need to reattach the
DIN-rail attachment plate, make sure the stiff metal spring is situated towards
the top, as shown in the figures below.
STEP 1:
Insert the top of the DIN-rail into the
slot just below the stiff metal spring.
STEP 2:
The DIN-rail attachment unit will
snap into place as shown below.
metal
spring
DIN-Rail
metal
spring
DIN-Rail
To remove the DIN-rail from the EDS, simply reverse Steps 1 and 2.
Wall Mounting (optional)
For some applications, you will find it convenient to mount the EDS on the
wall, as illustrated below.
STEP 1:
Remove the aluminum
DIN-rail attachment plate
from the EDS’s rear panel,
and then attach the wall
mount plates, as shown in
the figure.
⇒

- 5 -
STEP 2:
Mounting the EDS on the wall requires 4 screws. Use the switch,
with wall mount plates attached, as a guide to mark the correct
locations of the 4 screws. The heads of the screws should be less
than 6.0 mm in diameter, and the shafts should be less than 3.5
mm in diameter, as shown in the figure at the right.
6.0 mm
3.5 mm
NOTE Before tightening screws into the wall, make sure the screw head
and shank size are suitable by inserting the screw into one of the
keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2 mm to allow room for
sliding the wall mount panel between the wall and the screws.
STEP 3:
Once the screws are fixed in the
wall, insert the four screw
heads through the large parts of
the keyhole-shaped apertures,
and then slide the EDS
downwards, as indicated.
Tighten the four screws for
added stability.
⇒
II 3G
ATEX Information
1. Certificate number DEMKO 10 ATEX 0917324X
2. Ambient range (-40°C ≤Tamb ≤75°C)
3. Certification string (Ex nC nL IIC T4)
4. Standards covered ( EN60079-0:2006, EN60079-15:2005)
5. Electric data
Model No. Rated Supply Voltage and
Current
Relay Contact
Rating
EDS-G308,
EDS-G308-T
12-48 V dc, Class 2,
Maximum 0.65 A;
18-30 V ac, Class 2, 50/60
Hz, Maximum 0.5 A
EDS-G308-2SFP,
EDS-G308-2SFP-T
12-48 V dc, Class 2,
Maximum 0.71 A;
18-30 V ac, Class 2, 50/60
Hz, Maximum 0.55 A
24 V dc, 1 A,
resistive load
6. The conditions of safe usage:
zThese products must be mounted in an IP54 enclosure.
zInstall in an area of pollution degree 2 or less.
zUse power supply terminal conductors suitable for use in an ambient
temperature of 90°C
For ambient temperatures below –10°C and above +60°C use field wiring
suitable for both minimum and maximum ambient temperatures.

- 6 -
Wiring Requirements
WARNING
Safety First!
Turn the power off before disconnecting modules or wires. The
proper power supply voltage is listed on the product label. Check
the voltage of your power source to make sure you are using the
correct voltage. Do NOT use a voltage greater than what is
specified on the product label.
These devices must be supplied by an AELV source as defined in
the Low Voltage Directive 2006/95/EC and 2004/108/EC.
WARNING
Safety First!
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
You should also pay attention to the following items:
yUse separate paths to route wiring for power and devices. If power wiring
and device wiring paths must cross, make sure the wires are perpendicular
at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring in
the same wire conduit. To avoid interference, wires with different signal
characteristics should be routed separately.
yYou can use the type of signal transmitted through a wire to determine
which wires should be kept separate. The rule of thumb is that wiring with
similar electrical characteristics can be bundled together.
yKeep input wiring and output wiring separated.
yIt is strongly advised that you label wiring for all devices in the system
when necessary.
Grounding Moxa EtherDevice Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface, such as a metal panel.

- 7 -
Wiring the Alarm Contact
The Alarm Contact consists of the two middle contacts of the terminal block on
the EDS’s top panel. You may refer to the next section for detailed instructions
on how to connect the wires to the terminal block connector, and how to attach
the terminal block connector to the terminal block receptor.
In this section, we explain the meaning of the two contacts used to connect the
Alarm Contact.
FAULT
FAULT
Top View
Front View
FAULT: The two middle contacts of the
6-contact terminal block connector are used to
detect both power faults and port faults. The
two wires attached to the Fault contacts form
an open circuit when:
1. EDS has lost power from one of the AC/
DC power inputs.
OR
2. The PORT ALARM DIP switch for one of
the ports is set to ON, but the port is not
connected properly.
If neither of these two conditions is satisfied,
the Fault circuit will be closed.
Wiring the Redundant Power Inputs
The top two contacts and the bottom two contacts of the 6-contact terminal
block connector on the EDS’s top panel are used for the EDS’s two AC/ DC
inputs. Top and front views of one of the terminal block connectors are shown
here.
Top View
Front View
STEP 1: Insert the negative/positive AC/
DC wires into the V-/V+ terminals.
STEP 2: To keep the AC/ DC wires from
pulling loose, use a small flat-blade
screwdriver to tighten the wire-clamp
screws on the front of the terminal block
connector.
STEP 3: Insert the plastic terminal block
connector prongs into the terminal block
receptor, which is located on EDS’s top
panel.
ATTENTION
Before connecting the EDS to the AC/DC power inputs, make
sure the AC/DC power source voltage is stable.

- 8 -
Communication Connections
EDS-G308 models have 8 10/100/1000BaseT(X) Ethernet ports, or 6
10/100/1000BaseT(X) and 2 combination ports—10/100/1000T(X) and
100/1000BaseSFP.
10/100/1000BaseT(X) Ethernet Port
Connection
The 10/100/1000BaseT(X) ports located on Moxa EtherDevice Switch’s front
panel are used to connect to Ethernet-enabled devices. Most users will choose
to configure these ports for Auto MDI/MDI-X mode, in which case the port’s
pinouts are adjusted automatically depending on the type of Ethernet cable
used (straight-through or cross-over), and the type of device (NIC-type or
HUB/Switch-type) connected to the port.
In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports. We also give cable wiring diagrams for
straight-through and cross-over Ethernet cables.
10 /100Base T(x) RJ45 Pinouts
MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45
Pin Signal Pin Signal
1 Tx+ 1 Rx+
2 Tx- 2 Rx-
3 Rx+ 3 Tx+
6 Rx- 6 Tx-
1000BaseT RJ45 Pinouts
Pin MDI MDI-X
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
1 8
RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring
Straight-Through Cable
RJ45 Plug Pin 1
Switch Port
RJ45
Connector RJ45 Connecto
r
Tx+
Tx-
Rx+
Rx-
DD+
DD-
DC+
DC-
NIC Port
Cable Wiring Rx+
Rx-
Tx+
Tx-
DC+
DC-
DD+
DD-
3
6
1
2
4
5
7
8
3
6
1
2
4
5
7
8
1 8

- 9 -
RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring
Cross-Over Cable
RJ45 Plug Pin 1
Switch Port
(NIC Port)
RJ45
Connector RJ45 Connector
Tx+
Tx-
Rx+
Rx-
(Rx+)
(Rx-)
(Tx+)
(Tx-) DC+
DC-
DD+
DD-
(DD+)
(DD-)
(DC+)
(DC-)
(Tx+)
(Tx-)
(Rx+)
(Rx-)
Switch Port
(NIC Port)
Cable Wiring
Rx+
Rx-
Tx+
Tx- (DC+)
(DC-)
(DD+)
(DD-)
DD+
DD-
DC+
DC-
3
6
1
2
4
5
7
8
1
2
3
6
7
8
4
5
100Base-FX or 1000Base-X Fiber Port
The Fiber ports on the EDS-G308 series are SFP type slots, which support both
100Base-FX and 1000Base-X speed fiber transceiver to work properly. Moxa
provides complete transceiver models for various distance requirements.
Multi-mode:
1000BaseSX 0 to 550 m, 850 nm (50/125μm, 400MHz*km)
0 to 275 m, 850 nm (62.5/125μm, 200MHz*km)
1000BaseLX 0 to 1100 m, 1310 nm (50/125μm, 800MHz*km)
0 to 550 m, 1310 nm (62.5/125μm, 500MHz*km)
Single-mode:
1000BaseLX 0 to 10 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))
1000BaseLHX 0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))
1000BaseZX 0 to 80 km, 1550 nm (9/125μm, 19 PS/(nm*km))
Multi-mode:
100BaseFx 0 to 5 km, 1300 nm (50/125μm, 800MHz*km)
0 to 4 m, 1300 nm (62.5/125μm, 500MHz*km)
Single-mode:
100BaseFx 0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))
The concept behind the LC port and cable is quite straightforward. Suppose
you are connecting devices I and II. Unlike electrical signals, optical signals do
not require a circuit in order to transmit data. Consequently, one of the optical
lines is used to transmit data from device I to device II, and the other optical
line is used to transmit data from device II to device I, for full-duplex
transmission.
Remember to connect the Tx (transmit) port of device I to the Rx (receive) port
of device II, and the Rx (receive) port of device I to the Tx (transmit) port of
device II. If you make your own cable, we suggest labeling the two sides of the
same line with the same letter (A-to-A and B-to-B, as shown below, or
A1-to-A2 and B1-to-B2).

- 10 -
LC-Port Pinouts LC-Port to LC-Port Cable Wiring
Tx
Rx
A
B
Cable Wiring
A A
B B
A
B
ATTENTION
This is a Class 1 Laser/LED product. To avoid causing serious
damage to your eyes, do not stare directly into the Laser Beam.
Redundant Power Inputs
Both power inputs can be connected simultaneously to live AC/DC power
sources. If one power source fails, the other live source acts as a backup, and
automatically supplies all of the EDS’s power needs.
Alarm Contact
The Moxa EtherDevice Switch has one Alarm Contact located on the top panel.
For detailed instructions on how to connect the Alarm Contact power wires to
the two middle contacts of the 6-contact terminal block connector, see the
Wiring the Alarm Contact section on page 6. A typical scenario would be to
connect the Fault circuit to a warning light located in the control room. The
light can be set up to switch on when a fault is detected.
The Alarm Contact has two terminals that form a Fault circuit for connecting to
an alarm system. The two wires attached to the Fault contacts form an open
circuit when (1) EDS has lost power from one of the AC/DC power inputs, or
(2) one of the ports, for which the corresponding PORT ALARM DIP switch is
set to ON, is not properly connected.
If neither of these two conditions occurs, the Fault circuit will be closed.
DIP Switch Settings
ON DIP
12345678
21
----
BSP
PORT
ALARM
12/24/48 VDC
ONOFF
P1
P2
P3
P4
P5
P6
P8
P7
OFF ON
The default setting for each DIP switch is OFF. The
following table explains the effect of setting the DIP
switches to the ON positions.
DIP Switch Setting Description
ON Enables broadcast storm protection
BSP OFF Disables broadcast storm protection