Moxa Technologies EDR-G9010 Series User manual

P/N: 1802090101012
*1802090101012*
EDR-G9010 Series
Quick Installation Guide
Moxa Industrial Secure Router
Version 1.1, September 2021
Technical Support Contact Information
www.moxa.com/support

2021 Moxa Inc. All rights reserved.

- 2 -
Package Checklist
The EDR-G9010 Series, which is a secure router, is shipped with the
items listed below. If any of these items are missing or damaged,
please contact your customer service representative for assistance.
•1 Industrial secure router
•1 USB-C-to-DB9 cable
•Quick installation guide (printed)
•Protective caps for unused ports
•Warranty card
Features
Advanced Industrial Networking Capability
•All-in-one firewall/NAT/VPN/switch/router
•Full NAT capability with 1-to-1, N-to-1, and port forwarding
•Rugged hardware for -40 to 75°C operating temperature (T model)
•VRRP redundancy
•Firewall with Quick Automation Profiles for industrial protocol rules
•VPN for secure remote connections
•Intelligent Policy Check for quick troubleshooting
•Supports 1 WAN and up to 15 virtual LAN interfaces

- 3 -
Panel Views of EDR-G9010 Series
Front Panel
Top Panel
Front Panel:
1. USB port for ABC-02-USB
2. 1G/2.5G SFP port speed LED
indicator
3. 1G/2.5G SFP ports
4. 1G/2.5G SFP port speed LED
indicator
5.
1000 Mbps copper port speed
LED indicator
6. 10/100 Mbps copper port
speed LED indicator
7. 10/100/1000 Mbps copper
ports
8. Power input PWR1 LED
indicator
9. Power input PWR2 LED
indicator
10.
STATE LED indicator
11.
MSTR/H.TC LED indicator
12.
CPLR/T.TC LED indicator
13.
VRRP/HA LED indicator
14.
VPN LED indicator
15.
USB LED indicator
Top Panel:
1. Grounding screw
2. Terminal block with latch for
Power 2 input
3. Terminal block with latch for
Power 1 input
4. Terminal block with latch for
digital input
5. Terminal block with latch for
relay output
6. Type-C serial console port

- 4 -
Rear Panel
Rear Panel:
1. DIN-rail mounting kit
Mounting Dimensions

- 5 -
DIN-rail Mounting (DNV-certified)
In the package, the metal DIN-rail mounting kit is fixed to the back
panel of the EDR-G9010 Series. Mount the EDR-G9010 Series on a
corrosion-free mounting rail that adheres to the EN 60715 standard.
Suggested Installation Method
STEP 1:
Place
the upper lip of the DIN-rail
kit
onto the mounting rail.
STEP 2
:
Press the
EDR-G9010 Series
towards the mounting rail until it
snaps into place.
Suggested Removal Method
STEP 1:
Pull down the latch on the DIN
-rail
kit with a screwdriver.
STEPS 2 & 3
:
Slightly pull the
EDR-G9010 Series
forward and lift
it up to remove it
from the mounting rail.
Wall Mounting
For some applications, you will find it convenient to mount the EDR-
G9010 Series on the wall, as shown in the following illustrations.
STEP 1: Remove the aluminum DIN-rail attachment plate from the rear
panel of the EDR-G9010 Series, and then attach both the wall-
mounting plates with six M3 screws. The mounting plate holes are
marked B in the diagram below.

- 6 -
STEP 2: Mounting the EDR-G9010 Series on the wall requires two M3
screws. Use the EDR-G9010 Series with the wall mount plates attached
as a guide to mark the correct location of the two screws. The wall-
mounting holes are marked Ain the above diagram.
Wiring Requirements
WARNING
Do not disconnect modules or wires unless power has been
switched off or the area is known to be non
-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The
devices are designed for operation with a
Safety Extra
-
Low Voltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with
the Safety Extra
-Low Voltages (SELV) in compliance with
IEC 950/EN 60950-1/VDE 0805.
ATTENTION
This unit is a built
-
in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950
-1/EN60950-1
(or similar regulation).

- 7 -
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your
EDR-G9010 Series.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical
codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring
could overheat, causing serious damage to your equipment.
Please read and follow these guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power
wiring through the same wire conduit. To avoid interference, wires
with different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb
is that wiring sharing similar electrical characteristics can be
bundled together.
•You should separate input wiring from output wiring.
•We advise that you label the wiring to all devices in the system.
•This product is intended for installation in Restricted Access
Location.
WARNING
Hot Surface. Do not touch.
ATTENTION
The SFP module only supports Laser Class 1 optical
transceivers.
Grounding the EDR-G9010 Series
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from
the ground screw (M4 type) to the grounding surface prior to
connecting devices.
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface such as a metal panel.

- 8 -
Wiring the Redundant Power Inputs
The EDR-G9010 Series has two sets of power inputs—power input 1
and power input 2. The top and side views of the terminal block
connector are shown below.
Top View
Right View
STEP 1:
Use a small flat
-
blade screwdriver
to press a wire locker.
STEP 2:
Insert a positive/negative DC wire
into the V+/V
-
terminals
respectively.
STEP 3:
Release the wire locker, and check
whether the wire is fixed.
The input terminal block (TB1) should be installed using 16-24 AWG
wires.
The power cord adapter should be connected to a socket outlet with an
earthing connection. The power cord and adapter must comply with
Class II construction.
This product is intended to be supplied by a UL Listed Power Adapter or
DC power source marked ‘L.P.S’ or ‘Limited Power Source’, rated 12 to
48 VDC, 1.51 A (min.), and Tma 75°C (min.). If you require further
assistance, please contact your Moxa representative.
Communication Connections
Each EDR-G9010 Series has three types of communication ports:
•1 Type-C console port (RS-232 interface, baudrate: 115200, 8-N-1)
•8 10/100/1000BaseT(X) Ethernet ports
•2 1G/2.5G SFP ports
TYPE-C Console Port Connection
The EDR-G9010 Series provides one Type-C console port located on the
top panel. Connect the industrial secure router to a PC COM port using
the Type-C-to-DB9 connection cable, and then launch a console
terminal software, e.g. Moxa PComm Terminal Emulator, to access the
EDR-G9010 Series’ console configuration utility.
TYPE-C-to-DB9 Cable Wiring
P1 P2
2
A5
BROWN
B5
GREEN
3
A6
RED

- 9 -
B6
BLUE
5
A7
ORANGE
B7
PURPLE
PIN Definition
Description
P1
P2
TXD
2
A5, B5
RXD
3
A6, B6
GND
5
A7, B7
10/100/1000BaseT(X) Ethernet Port Connection
The 10/100/1000BaseT(X) ports located on the EDR-G9010 Series front
panel are used to connect to Ethernet-enabled devices. Most users will
choose to configure these ports for Auto MDI/MDI-X mode, in which
case the port’s pinouts are adjusted automatically depending on the
type of Ethernet cable used (straight-through or cross-over), and the
type of device (NIC-type or HUB/Switch-type) connected to the port.
No matter which case you are connecting, we share pinouts for both
MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports.
10/100Base T(x) RJ45 Pinouts
MDI Port Pinouts
MDI-X Port Pinouts
8-pin RJ45
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Pin
Signal
1
Rx+
2
Rx-
3
Tx+
6
Tx-
1000BaseT RJ45 Pinouts
Pin
MDI
MDI-X
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
The Reset Button
Using a pointed object such as a straightened paperclip or toothpick,
depress the Reset button for five seconds to load the factory default
settings. When pressing down, the STATE LED will start to blink about
once per second. Continue to depress until the STATE LED begins
blinking more quickly, indicating that the device is resetting and you
can release.
NOTE
DO NOT power off the device when loading default settings.
LED Indicators
The front panel of the EDR-G9010 Series has several LED indicators.
The function of each LED is described in the following table:

- 10 -
LED
Color
State
Description
PWR1 Amber
On Power is being supplied to power input
P1 on the main module.
Off
Power is NOT being supplied to power
input P1 on the main module.
PWR2 Amber
On
Power is being supplied to power input
P2 on the main module.
Off Power is
NOT
being supplied to power
input P2 on the main module.
STATE
Green
On
The system passed the self-diagnosis
test on boot-up and is ready to run.
Blinking
Device reset is in progress, blinking
once per second.
Red On The system failed the self-
diagnosis test
on boot-up.
MSTR/
H.TC Green
On
The EDR-G9010 is set as the Master of
the Turbo Ring, or as the Head of the
Turbo Chain.
Blinking The Turbo Ring or the Turbo Chain is
down.
Off
The EDR-G9010 is not set as the Master
of this Turbo Ring or is set as a
Member
of the Turbo Chain.
CPLR/
T.TC Green
On
The EDR-G9010 Series’ coupling
function is enabled to form a backup
path, or the device is set as the Tail of
the Turbo Chain.
Blinking The Turbo Ring or the Turbo Chain is
down.
Off
The EDR-G9010 Series’ coupling
function is disabled, or the device is set
as a Member of the Turbo Chain.
VRRP/HA Green
On The EDR-G9010 is set as the Master of
the VRRP or HA.
Off
The EDR-G9010 is not set as the Master
of the VRRP or HA.
VPN
Green
On
All VPN tunnels are working normally.
Amber On
Only parts of the VPN tunnels are
working normally.
Off
No active VPN connections.
USB Green
On
USB drive successfully connected.
Blinking
USB data is being transmitted.
Red
On
USB dongle malfunction.
1G/2.5G
Green
On
2.5G SFP link is up.
Amber
On
1G SFP link is up.
Off
No link or the SFP link is down.
Specifications
Input Current
1.51 A @ 12 V
0.70 A @ 24 V
0.35 A @ 48 V
Input Voltage 12/24/48 VDC, dual power input
DNV-certified for 24 VDC