Moxa Technologies SDS-3008 Series User manual

Moxa Industrial Smart Ethernet Switch
User’s Manual
Edition 1.0, January 2017
www.moxa.com/product
Models covered by this manual:
SDS-3008 series
© 2017 Moxa Inc. All rights reserved.

Moxa Industrial Smart Ethernet Switch
User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2017 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. About this Manual ............................................................................................................................. 1-1
2. Quick Start Guide .............................................................................................................................. 2-1
Connecting to the Switch for the First Time............................................................................................2-2
Important Reminders ..........................................................................................................................2-4
Change the Default Password! ......................................................................................................2-4
Configure the Smart Switch's Date and Time Settings......................................................................2-4
UI Dashboard.....................................................................................................................................2-5
Management Bar Buttons and Functionality............................................................................................2-5
Configuration Panel Icons and Functionality ...........................................................................................2-7
Detailed Descriptions of Management Bar Buttons ..................................................................................2-8
Management Interface Instructions ...............................................................................................2-8
Port Mirror Instructions ................................................................................................................2-9
Inventory Report Download ........................................................................................................ 2-10
Log File Backup Instructions ....................................................................................................... 2-10
Configuration Backup and Restore Instructions ............................................................................. 2-12
Firmware Upgrade Instructions ................................................................................................... 2-14
User Account Instructions........................................................................................................... 2-15
3. Management Functions ..................................................................................................................... 3-1
Switch Information .............................................................................................................................3-2
System Information.....................................................................................................................3-2
Network Information....................................................................................................................3-3
Date and Time Information...........................................................................................................3-5
Switch Panel and Profile ......................................................................................................................3-9
Switch Panel and Statistics ...........................................................................................................3-9
Industrial Protocols and SNMP Settings ........................................................................................ 3-10
Port Settings............................................................................................................................. 3-16
RSTP Settings ........................................................................................................................... 3-17
VLAN Settings........................................................................................................................... 3-20
Switch Log....................................................................................................................................... 3-22
Switch Log Table ....................................................................................................................... 3-22
Warning Notification Settings ...................................................................................................... 3-23
A. The STP/RSTP Concept ..................................................................................................................... A-1
What is STP?......................................................................................................................................A-1
How STP Works ..................................................................................................................................A-2
STP Requirements .......................................................................................................................A-2
STP Calculation ...........................................................................................................................A-3
STP Configuration........................................................................................................................A-3
STP Reconfiguration ....................................................................................................................A-3
Differences between STP and RSTP .......................................................................................................A-3
B. The Virtual LAN (VLAN) Concept ....................................................................................................... B-1
What is a VLAN? .................................................................................................................................B-1
Benefits of VLANs ........................................................................................................................B-1
VLANs and the Rackmount switch..................................................................................................B-2
Managing a VLAN ........................................................................................................................B-2
Communication between VLANs ....................................................................................................B-2
VLANs: Tagged and Untagged Membership.....................................................................................B-2
Sample Applications of VLANs Using Moxa Switches ................................................................................B-3

1
1. About this Manual
Thank you for purchasing a Moxa Industrial Smart Ethernet Switch. Read this user’s manual to learn how to
connect your Moxa Industrial Smart Ethernet Switch to Ethernet-enabled devices used for industrial
applications.
Read the following two chapters to learn how to use your Moxa smart switch:
Chapter 2: Quick Start Guide
In chapter 2, we explain how to configure your smart switch the first time you use it, and give an overview
of the management function icons that are accessible from the switch’s browser-based UI. The
easy-to-recognize icons that appear on the UI dashboard effectively reduce deployment time, simplify
maintenance, and enhance manageability.
Chapter 3: Management Functions
In chapter 3, we explain in detail how to access, configure, and use the various management functions
supported by your Moxa smart switch. All of the functions can be easily accessed and configured through a
web browser.

2
2. Quick Start Guide
The Moxa industrial smart Ethernet switch has a browser-based UI with easy-to-recognize icons on the UI
dashboard to effectively reduce deployment time, simplify maintenance, and enhance manageability. Read this
chapter before using your Moxa smart switch for the first time.
The following topics are covered in this chapter:

Connecting to the Switch for the First Time

Important Reminders
Change the Default Password!
Configure the Smart Switch's Date and Time Settings

UI Dashboard

Management Bar Buttons and Functionality

Configuration Panel Icons and Functionality

Detailed Descriptions of Management Bar Buttons
Management Interface Instructions
Port Mirror Instructions
Inventory Report Download
Log File Backup Instructions
Configuration Backup and Restore Instructions
Firmware Upgrade Instructions
User Account Instructions

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-2
Connecting to the Switch for the First Time
To connect to your Moxa smart switch for the first time, use a standard Ethernet cable to connect your
computer’s Ethernet port to any of the switch’s Ethernet ports. You will need to know the switch’s factory
default settings, which are shown in the following table:
Smart Switch Factory Default Settings
Configuration Item Default Setting
IP Address 192.168.127.253
Subnet Mask 255.255.255.0
Usernames admin, user
Password moxa
Management VLAN 1
Step 1: Configure your computer's network settings
To establish a connection between your computer and the Moxa smart switch, the smart switch and computer
must be connected to the same logical subnet.
For example, for a Windows computer, open the Internet Protocol Version 4 (TCP/IPv4) Properties page,
set subnet mask to 255.255.255.0, and the IP address to 192.168.127.252.
Step 2: Configure the resolution of your computer screen
For best results, set the resolution of your PC’s display to 1024 x 768 pixels.
Step 3: Connect to the smart switch’s browser-based UI
1. Open your computer’s web browser and enter the IP address (default: 192.168.127.253) of the connected
smart switch in the Address or URL field at the top of the browser window.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-3
2. When the smart switch’s web console opens, type in the Username (default: admin) and Password (default:
moxa) and then click the Login button to log in.
3. Click Continue on the welcome page to proceed.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-4
4. After logging in, you may need to wait a few moments for the web console to appear.
Important Reminders
Change the Default Password!
Be sure to
change the password of your Moxa smart switch the first time you use the switch.
To reduce the chance that hackers will access your smart switch and your network, be sure to change the
factory default password (moxa) the first time you use the switch. If the password has not been changed, the
following popup window will appear each time you log in:
See the User Account Instructions section in chapter 3 to learn how to change the password.
Configure the Smart Switch's Date and Time Settings
Configure the switch’s internal date and time settings the first time you log in to your Moxa smart switch.
Setting the correct date and time is important because the switch’s log and trap functions use a date/time
stamp.
See the Date and Time Information section in the chapter 3 for details.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-5
UI Dashboard
The dashboard of the Moxa smart switch’s browser-based UI consists of three parts:
1.
Switch Information Bar:Displays basic switch information, including the model name, MAC address,
serial number, and firmware version.
2.
Management Bar:The clickable icons (referred to below as “management buttons” or simply “buttons”
)
displayed on the Management Bar can be used to perform various management functions. For a detailed
explanation of each button, refer to the Management Bar Icons and Functionality
section later in this
chapter.
3.
Configuration Panels:The configuration panels section includes three panels: S
witch
Information, Switch Profile, and Switch Log. Click any of the pencil icons to configure
the items nearest the icon. For a detailed explanation of each
configuration item, refer
to Chapter 3: Management Functions.
Pencil Icon
Management Bar Buttons and Functionality
The 11 icons on the Moxa smart switch’s management bar can be used to perform a variety of
management-type operations. The name of each button and the button’s functionality are detailed below:
Icon Function Description
Switch Locator Click the Switch Locator button to locate the switch you are
currently connected to. When the button is clicked,
the STATE and
FAULT LEDs on the switch will blink green and red, respectively,
twice per second for a period of 30 seconds.
Factory Default Click the Factory Default button to restore the smart switch
settings to factory default values. A popup window will appear
asking you to click OK to proceed with the reset action, or Cancel
to cancel the request.
A factory reset button is also located on the top panel of the switch
itself. Refer to the SDS-3008 Series Quick Installation Guide,
which can be downloaded from Moxa’
s website, for instructions on
how to use the reset button.
Restart System Click the Restart System button to initiate a “warm restart” of
the
Moxa smart switch’s operating system. A popup window will appear
asking you to click OK to proceed with the reset action, or Cancel
to cancel the request.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-6
Icon Function Description
Management
Interface
Click the Management Interface button to update the TCP Port
numbers for various web protocols, the maximum number of u
sers
who can be logged in simultaneously to various protocols, and
the
auto logout time setting. These settings can be used to better
control network security. For a detailed explanation of each
setting, see the Management Interface Instructions section
later this chapter.
Port Mirror Click the Port Mirror button
to configure a monitored port, sniffer
mode, and mirror port. The mirror port can be configured to
transmit the same data being transmitted to and/or from the
monitored port, allowing the network administrator to “sniff” the
observed port to keep an eye on network activity. For a detailed
explanation of each setting, see the Port Mirror Instructions
section later in this chapter.
NOTE: Only sniffed traffic will be transmitted through the mirror
port.
NOTE: When the port mirror function is activated, the gray ports on
the Port Mirror Button will change to blue.
Inventory Report
Download
Click the Inventory Report Download button to download a
text
file that summarizes information related to the switch. The text file
can be used to improve device management and for archiving. The
text file will be named as follows:
“[Switch Name]_inventory_report.txt”.
For an overview of the content that will be downloaded, see the
Inventory Report Download section later in this chapter.
Log File Backup Click the Log File Backup button to back up the smart switch’s
log
files. When the Log File Backup dialog window opens, select one of
three backup methods: to a local drive, to a remote TFTP server, or
save to Moxa Auto Backup Configurator (ABC-02). You may also
select the “Automatically back up the event log to prevent it from
being overwritten” option at the bottom of the dialog window. For a
detailed explanation of the settings, see the Log File Backup
Instructions section later in this chapter.
NOTE: Moxa industrial smart Ethernet switches can store a
maximum of 1000 event log entries. When the 1000-entry storage
limit is reached, the switch will overwrite and delete the oldest
saved event log.
Configuration
Backup and
Restore
Click the Configuration Backup and Restore button to enable
your Moxa smart switch’s configuration backup and restore
function. When the settings window opens, select one of three
backup and restore options: using a local computer, using a
remote TFTP server, or using a Moxa Auto Backup Configurator
(ABC-02). You may also require the configuration file to be
encrypted, and configure the configuration backup and restore
function to automatically load configurations from and back up
configurations to an ABC-02 device attached to the switch. For a
detailed explanation of the settings, see the Configuration
Backup and Restore Instructions section later in this chapter.
NOTE: When
encryption is enabled, you must set a password, and
use the password when restoring the
configuration from a backup
file.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-7
Icon Function Description
Firmware Upgrade
Click the Firmware Upgrade button to upgrade the firmware
through either a local drive, remote TFTP server, or Auto Backup
Configurator (ABC-02). For a detailed description of this function,
see the Firmware Upgrade Instructions section later in this
chapter.
User Account Click the User Account button to create, manage, or remove
accounts and corresponding settings. For a detail
ed description of
this setting, see the User Account Instructions section later in
this chapter.
NOTE: The active username and the user’s corresponding access
right are displayed to the right of the Management Bar buttons.
For
example: [Admin] admin
Logout Click the Logout button to manually log out of the switch’s web
console. Note that you can use the Management Interface function
described above to configure the switch to automatically log out of
the web console if the connection with the user is idle for a preset
time period.
Configuration Panel Icons and Functionality
Icon Function Description
Edit Click any of the Edit buttons in the Switch Configuration
Information section to edit the settings of items located near the
edit icon.
Industrial Protocols
and SNMP Profiles
The Moxa smart switch supports three industrial protocols:
PROFINET, EtherNet/IP, and Modbus TCP; and one management
protocol: SNMP. When activated, PROFINET, Modbus TCP,
EtherNet/IP, and/or SNMP statuses are transmitted to, and
instructions are received from, devices connected to the switch.
Such information can be displayed on a SCADA HMI or NMS
system.
If the protocol is active, the protocol button will be green (as shown
at the left). If the protocol is inactive, the protocol button will be
gray. Click the protocol button once to change the protocol from
active to inactive or vice versa.
NOTE: If you need to integrate the smart switch with an
EtherNet/IP network for I/O operations, then IGMP Snooping and
IGMP Query may be needed; when you click the EtherNet/IP
button, the smart switch enables IGMP Snooping and IGMP Query
automatically.
NOTE: To configure additional SNMP settings, left click the SNMP
button to enter the SNMP settings page.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-8
Detailed Descriptions of Management Bar
Buttons
Management Interface Instructions
The following screenshot gives an overview of the management interface settings page, including details of
each parameter.
Enable HTTP
Setting Description Factory Default
Select/Deselect Select the checkbox to enable HTTP. TCP Port: 80
Enable HTTPS
Setting Description Factory Default
Select/Deselect Select the checkbox to enable HTTPS. TCP Port: 443
Enable Telnet
Setting Description Factory Default
Select/Deselect Select the checkbox to enable Telnet. TCP Port: 23
Enable SSH
Setting Description Factory Default
Select/Deselect Select the checkbox to enable SSH. TCP Port: 22
Enable Moxa Service
Setting Description Factory Default
Select/Deselect Select the checkbox to enable Moxa Service.
NOTE: Moxa Service only applies to the Moxa network
management software suite.
TCP Port: 4000
UDP Port: 4000
Enable Moxa Service (Encrypted)
Setting Description Factory Default
Select/Deselect Select the checkbox to enable Moxa Service (Encrypted).
NOTE: Moxa Service (Encrypted) only applies to the Moxa
network management software suite.
TCP Port: 443
UDP Port: 40404

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-9
Maximum Login Users for HTTP+HTTPS
Setting Description Factory Default
Integer (1 to 10) Sets the maximum number of users who can log in to
HTTP and
HTTPS simultaneously.
5
Auto Logout Setting (min)
Setting Description Factory Default
Integer (0 to 1440) Sets the web auto logout period.
(Enter 0 to disable this function.)
5
NOTE: Press Apply once all settings have been properly set to activate the function.
Port Mirror Instructions
The following screenshot gives an overview of the port mirror settings page and details of each parameter.
Port Mirror
Setting Description
Monitored Port Select which ports will be monitored.
Sniffer Mode Select one of the following three watch direction options:
•RX: Select this option to monitor only those data packets coming into the Moxa
switch’s port.
•TX: Select this option to monitor only those data packets being sent out through the
Moxa switch’s port.
•TX/RX: Select this option to monitor data packets both coming into, and being sent
out through, the Moxa switch’s port.
Mirror Port Select the number of the port that will be used to monitor the activity of the monitored
port.
NOTE: Press Apply once all settings have been properly set to activate the function.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-10
Inventory Report Download
This text file will be downloaded and saved with the following filename:
[Switch Name]_inventory_report.txt.
Information like factory and switch Information will be summarized in a systematic way in this file. Users can
also import this text file into Microsoft Excel. Here is example:
Log File Backup Instructions
The log file backup settings page has two main sections. The first section can be used to manually select the
destination to which the log file will be saved, and the second part can be used to activate the automatic backup
of the event log to prevent it from being overwritten.
Log File Backup Method
Setting Description Factory Default
Local Select Local and click the Backup but
ton to back up the log file
to a local drive.
Local
TFTP Server Select TFTP Server, enter the Server IP and File Name, and
then click the Backup button to back up the log file.
Auto Backup
Configurator (ABC-02)
Select Auto Backup Configurator (ABC-02) and then click
Backup to save the configuration file to a connected ABC-02.
The file will be saved in the ABC-02’s Moxa folder
with filename
and extension as Sys.log.
NOTE: Select the proper method and press Backup to start the backup.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-11
Automatically Backup the Event Log
Setting Description Factory Default
Automatically backup
the event log to
prevent it from being
overwritten
This function is designed to maintain a long-
term record of the
switch’s log files. Moxa Ethernet switches are
capable of saving
1000 event log entries. When the 1000-entry storage limit is
reached, the switch over write
the oldest saved event log. The
ABC-02 can be used to back up these event logs. When the
number of switch log entries reaches 1000, the oldest 100
log
entries will first be copied from the switch to the ABC-02
before
they are over written.
Enable the
Automatically backup the event log to prevent
it being overwritten option, and then click Apply
. After that,
when the ABC-02 is plugged into the switch, the event logs wil
l
always be saved to the ABC-02 automatically when the
number
of switch log entries reaches 1000. Each backup action saves
the oldest 100 logs to the ABC-02 in one
file, with the filename
generated by the current system time as MMDDHHmm.log.
The file is saved to the His_log folder.
NOTE: MM=month, DD=day, HH=hour, mm=minutes, from
the system time.
unchecked
NOTE: Press Apply once to activate the automatic backup function. Be sure an ABC-02 has been attached to
the Moxa industrial smart Ethernet switch’s USB storage port before activating the function.
The following information is included in a log file:
Index An event index assigned to identify the event sequence.
Bootup
Number
This field shows how many times the Moxa switch has been rebooted or cold started.
Date The date is updated based on how the current date is set on the System Settings page.
Time The time is updated based on how the current time is set on the System Settings page.
System
Startup Time
The system startup time related to this event.
Event Events that have occurred.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-12
Configuration Backup and Restore Instructions
The configuration backup and restore settings page has three main sections. The first section is used to
manually select the destination for backing up and restoring the configuration, the second section is used to set
the password for encrypting the downloaded configuration files, and the third section is used to activate
automatically restoring the configuration file from an attached ABC-02 when the switch is booted up and
backing up the configuration automatically to the attached ABC-02 whenever there is any change.
Configuration Backup and Restore
Setting Description Factory Default
Local 1. Select Local and click the Backup button to back up the
configuration file (the file will be named Sys.ini) to a local
drive.
2. Click Browse to search for a configuration on a local disk,
and then click the Restore button.
Local
TFTP Server 1. Select TFTP Server and enter the TFTP server’s IP address.
2. Input the backup/restore file name (supports up to 54
characters, including the .ini file extension) and then click
the Backup/Restore button.
Auto Backup
Configurator (ABC-02)
1. Click Backup to save the configuration file to the ABC-02.
The file will be saved in the ABC-02’s Moxa folder
as a *.ini
file (e.g., Sys.ini).
2. Click Browse
to select the configuration file, and then click
Restore to start loading the configuration into the switch.
NOTE: two files will be saved to the ABC-02-USB’s Moxa
folder: Sys.ini and MAC.ini. The purpose of saving the two
files is to identify which file will be used when Auto load
configuration from ABC to system when boot up is
activated. MAC.ini is named using the last 6 digits of the
switch’s MAC address, without spaces.
NOTE: Select the method you would like to use and then press Backup to start the backup operation.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-13
Configuration File Encryption Setting
Setting Description Factory Default
Enable Password 1. In order to back up an encrypted configuration file from a
smart switch, select the checkb
ox and type in a password to
enable encrypting the configuration file when it is
downloaded.
2. When loading the encrypted configuration file into a smart
switch, first enable the function and type in the
corresponding password to decrypt the configuration file
while it is being loaded.
unchecked
Automatically Load and Restore the Configuration
Setting Description Factory Default
Automatically load
configurations from
the
ABC-02 to the system
when booting up
1. Enable this function by selecting the Automatically load
configurations from ABC-02 to the system when
booting up checkbox and then click Apply.
2. Power off your switch first, and then plug in the ABC-02.
When you power on your switch, the system will
detect the
configuration file on the ABC-02 automatically. The switch
will recognize the file name, with the following sequence
priority:
•First priority: MAC.ini
•Second priority: Sys.ini
If no matching configuration file is found, the fault LED light
will turn on, and the switch will boot up normally.
NOTE: The MAC.ini configuration file should be named using
the last 6 digits of the switch’s MAC address, without spaces.
Checked
Automatically backup
to ABC-02 when
configurations change
1. Enable this function by checking the Automatically
backup to ABC-02 when configurations change
checkbox and then click Apply.
2. Attach a Moxa ABC-02 for backing up the switch
configuration files automatically. Once the current
configuration is modified, the switch will back up the
modified configuration to the /His_ini folder on the
ABC-02. The file name will be the system date/time
(MMDDHHmm.ini).
NOTE: MM=month, DD=day, HH=hour, mm=minutes, from
the system time.
unchecked

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-14
Firmware Upgrade Instructions
There are three ways to update the Moxa industrial smart Ethernet switch’s firmware: from a local *.rom file,
by remote TFTP server, and with Auto Backup Configurator (ABC-02).
Local
1. Download the updated firmware (*.rom) file from Moxa’s website (www.moxa.com).
2. Click Browse to locate the (*.rom) file, and then click the Upgrade button.
TFTP Server
1. Enter the TFTP server’s IP address.
2. Input the firmware file name (*.rom) and click the Upgrade button.
Auto Backup Configurator (ABC-02)
1. Download the updated firmware (*.rom) file from Moxa’s website (www.moxa.com).
2. Save the file to the ABC-02’s Moxa folder. The filename cannot be longer than 8 characters, and the file
extension must be .rom.
3. Browse for the firmware (*.rom) file from the ABC-02, and then click the Upgrade button.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-15
User Account Instructions
The Moxa industrial smart Ethernet switch supports the management of accounts, including establishing,
activating, modifying, disabling, and removing accounts. There are two levels of configuration access: admin
and user. Accounts with admin privilege have read/write access of all configuration parameters, whereas
accounts with user privilege only have read access to view configuration items.
NOTE
1.
In order to maintain a higher level of security, we strongly suggest that you change th
e password after first
loggin in.
2.
By default, there will be an “admin” user account with admin privilege and a “user” user account with
user
privilege. The accounts can be deleted or disabled but
at least one account with admin privilege activated
must be maintained at all times.
3.
You can create up to a maximum of 10 accounts.
The User Account settings page is divided into a top section and a bottom section. To modify the settings of
a particular account, click the username for the account in the bottom section to highlight the line associated
with the account, and then change the settings for the account in the top section of the page.
Creating a New Account
Type in the user name and password, assign an authority to the new account, and then click Create.
Setting Description Factory Default
Active Check the Active checkbox to activate the account; uncheck
the checkbox to deactivate the account.
checked
Authority Select admin to assign read/write access to this account; the
user will be able to configure all parameters.
Select user to assign read-only access to this account; the user
will only be able to view configuration parameters.
admin
User Name
(Max. of 30
characters)
User Name None
Password Password for the user account (between 4 and 16 characters) None
Confirm Password Re-type in the password to further confirm the setting. None
NOTE: The naming rule stipulated by SNMPv3 and industrial protocols requires passwords to be more than 8
characters in length; spaces are not allowed.

Moxa Industrial Smart Ethernet Switch Quick Start Guide
2-16
Modifying an Existing Account
Select an existing account from the Account List table, modify the account details (authority, user name,
password, etc.), and then click Apply to save the changes.
Activate or Deactivate an Existing Account
Select an existing account from the Account List table, check or uncheck the Active check box, and then click
Apply to save the changes.