Moxa Technologies ioLogik E1200 Series User manual

P/N: 1802012001014
*1802012001014*
ioLogik E1200 Series
Quick Installation Guide
Edition 5.0, September 2016
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2016 Moxa Inc. All rights reserved.

- 2 -
Overview
The ioLogik E1200 series comes with 2 embedded Ethernet switch ports
that can form a daisy-chain topology, which is the easiest way to add
more Ethernet devices to a network or connect your ioLogiks in series.
Moxa’s free Active OPC Server offers active (or “push”) communication
that works between Moxa’s ioLogik units and HMI/SCADA systems,
providing instant I/O status reports by “Active Tags.” The event-driven
active tags result in an I/O response time that is faster than other OPC
Server packages.
Model Selection:
ioLogik
DI
DO
DIO
Relay
AI
AO
RTD
TC
E1210
16
-
-
-
-
-
-
-
E1211
-
16
-
-
-
-
-
-
E1212
8
-
8
-
-
-
-
-
E1213*
8
4
4
-
-
-
-
-
E1214
6
-
-
6
-
-
-
-
E1240
-
-
-
-
8
-
-
-
E1241
-
-
-
-
-
4
-
-
E1242
4
-
4
-
4
-
-
-
E1260
-
-
-
-
-
-
6
-
E1262
-
-
-
-
-
-
-
8
*The ioLogik E1213 has source DOs.
Package Checklist
•1 ioLogik E1200 series remote I/O product
•Quick installation guide (printed)
Specifications
System
Ethernet
2 x 10/100 Mbps switch ports, RJ45
Protection
1.5 KV magnetic isolation
Protocols
Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, HTTP
Power Input
24 VDC nominal, 12 to 36 VDC
Wiring
I/O cable max. 14 AWG
Dimensions
27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in)
Weight
under 200 g
Operating Temperature
Standard Models:
-10 to 60°C (14 to 140°F)
Wide Temp. Models:
-40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity
5 to 95% (non-condensing)
Altitude
Up to 2000 m
Note: Contact Moxa if you require products guaranteed to function
properly at higher altitudes.
Standards and
Certifications
UL 508, CE, FCC Class A
Warranty Period
5 years (excluding ioLogik E1214*)
Details
See www.moxa.com/warranty
*Because of the limited lifetime of power relay, products that use this
component are covered by a 2-year warranty.

- 3 -
Digital Input
Sensor Type
NPN, PNP, and Dry contact
I/O Mode
DI or Event Counter
Dry Contact
• On: short to GND
• Off: open
Wet Contact (DI to COM)
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Isolation:
3K VDC or 2K Vrms
Counter/Frequency:
250 Hz, power off storage
Digital Output (Sink)
I/O Mode
DO or Pulse Output
Pulse Wave
Width/Frequency
1 ms/500 Hz
Over-voltage Protection
45 VDC
Over-current Protection
2.6 A (4 channels @650 mA)
Over-temperature
Shutdown
175°C (typical), 150°C (min.)
Current Rating
200 mA per channel
Isolation
3K VDC or 2K Vrms
Digital Output (Source)
I/O Mode
DO or Pulse Output
I/O Type
Source
Current
0.5A per channel
Voltage
For DIO channel:
15 to 30 VDC (ext power voltage)
For DO channel:
15 to 30 VDC (ext
power voltage), 12 or 9 VDC
configurable by jumper.
Pulse Wave
Width/Frequency
1 ms/500 Hz
Over-voltage Protection
41 VDC
Over-current Limit
6 A
Over-temperature
Shutdown
175°C (typical), 150°C (min.)
Output Current Rating
1.5 A per channel
Relay Output
Type
Form A (N.O.) relay outputs, 5A
Contact Rating
5 A @ 30 VDC, 5 A @ 250 VAC, 5 A @ 110 VAC
Inductance Load
2 A
Resistance Load
5 A
Breakdown Voltage
500 VAC
Relay On/Off Time
1500 ms (max.)
Initial Insulation
Resistance
1G min. @ 500 VDC
Expected Life
100,000 times (typical)
Initial Contact Resistance
30 milli-ohms (max.)
Pulse Output
0.3 Hz at rated load
Analog Input
Type
Differential input
Resolution
16 bits
I/O Mode
Voltage / Current
Input Range
0 to 10 VDC, 4 to 20 mA

- 4 -
Accuracy
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
±0.5% FSR @ -40 and 75°C
Sampling Rate (all
channels)
12 samples/second
Input Impedance
10M ohms (min.)
Built-in Resistor for
Current Input
120 ohms
Analog Output
Resolution
12 bits
Output Range
0 to 10 VDC, 4 to 20 mA
Voltage Output
10 mA (max.)
Accuracy
±0.1% FSR @ 25°C
±0.3% FSR @ -40 and 75°C
Load Resistor
Internal register: 400 ohms
Note: 24 V of external power is required when loading > 1000 ohms.
RTD
Input Type
PT50, PT100, PT200, PT500, PT1000
Resistance
1–310, 1–620, 1–1250, 1–2200 ohms
Sampling Rate
12 samples/sec (all channels)
Resolution
16 bits
Accuracy
±0.1% FSR @ 25°C
±0.3% FSR @ -40 and 75°C
Input Impedance
625k ohms
Thermocouple Input
Sensor Type
J, K, T, E, R, S, B, N
Millivolt Type
±78.126 mV, ±39.062 mV, ±19.532 mV
Fault and Overvoltage
protection
±35 VDC (power off); +30 VDC, -25 VDC
(power on)
Sampling Rate
12 samples/sec (all channels)
Resolution
16 bits
Accuracy
±0.1% FSR @ 25°C
±0.3% FSR @ -40 and 75°C
Input Impedance
10M ohms
Installation
Connecting the Power
Connect the +12 to +36 VDC power line to the ioLogik E1200’s terminal
block V+ terminal; connect the ground from the power supply to the V-
terminal. Connect the ground pin ( ) if earth ground is available.
NOTE
For safety reasons, wires connecting the power supply should be
at least 2 mm in diameter (e.g., 12 gauge wires).

- 5 -
Jumper Settings
Models with DIO, AI, or external power channels require configuring the
jumpers inside the enclosure. Remove the screw located on the back
panel and open the cover to configure the jumpers.
DIO mode configurations are
shown above (Default: DO Mode).
Analog mode configurations are
shown above (Default: Voltage
Mode).
DOs on the ioLogik E1213 have 3
possible external (EXT) power
configurations, which are shown to
the right. Only one field power can
be selected at a time (JP10 / 12V JP5
/ 9V JP11)
and
the jumper must be
inserted vertically, not horizontally
(Default: Field Power JP10).
NOTE
The ioLogik E1213 has 4 pure DO channels and 4 hybrid DIO
channels. For the 4 pure DO channels, you can use the jumpers to
select the power configuration output (i.e., field power, 12 V, 9
V). But for the 4 hybrid DIO channels, you cannot use the
j
umpers to select the power configuration output. Instead, you
can only use the jumpers to set the DIO channels to either DI
mode or DO mode.
Mounting
There are two sliders on the back of the unit for DIN rail and wall
mounting.
1. Mounting on a DIN rail: Pull out the bottom slider; latch the unit
onto the DIN-rail, and push the slider back in.
2. Mounting on the wall: Pull out both the top and bottom sliders and
align the screws accordingly.
Connecting to the Network
The ioLogik E1200 has two built-in RJ45 Ethernet ports for connecting
standard direct or cross-over Ethernet cables.

- 6 -
LED Indicators
Type
Color
Description
Power
Amber
System power is ON
Off
System power is OFF
Ready
Green
System is ready
Flashing
Flashes every 1 sec when the “Locate”
function is triggered
Flashing
Flashes every 0.5 sec when the firmware is
being upgraded
Flashing
An on/off period cycle: 0.5 second shows
“Safe Mode”
Off
System is not ready.
Port 1
Green
Ethernet connection enabled
Flashing
Transmitting or receiving data
Port 2
Green
Ethernet connection enabled
Flashing
Transmitting or receiving data
EXT
(E1213 only)
Green
EXT field power input is connected
Off
EXT field power input is disconnected
I/O Wiring
Digital Inputs/Outputs
Analog Inputs/Outputs

- 7 -
Relay Output (Form A)
RTD Inputs
TC Inputs
System Configuration
Configuration via Web Console
Main configuration of an ioLogik E1200 is by web console.
•Default IP Address: 192.168.127.254
•Subnet Mask: 255.255.255.0
NOTE
Be sure to configure the host PC’s IP address to the same subnet
as the ioLogik E1200. For example, 192.168.127.253
ioSearch Utility
ioSearch is a search utility that helps users locate an ioLogik E1200 on the
local network. The utility can be downloaded from Moxa’s website.

- 8 -
Load Factory Default Settings
There are three ways to restore the ioLogik E1200 to factory default
settings.
1. Hold the RESET button for 5 seconds.
2. In the ioSearch utility, right-click on the ioLogik device to be reset and
select Reset to Default.
3. Select Load Factory Default from the web console.
Modbus Address Table
Consult the user’s manual for the ioLogik’s Modbus address, or find the
default address of the I/O channels in the web console by clicking
User-defined Modbus Addressing Default Address.
Active OPC Server Connection
Connect the ioLogik E1200 to an Active OPC Server by following the steps
below:
1. Disable the user-defined Modbus address function.
2. Download Active OPC Server Lite utility from Moxa's website and
install it.
3. Install from Web console Active OPC Server Settings AOPC
& I/O Settings; specify the IP address where the Active OPC Server
is installed. Specify the I/O channels that need to be added to Active
OPC Server Lite. Submit the settings and then Save/Restart.
4. From Web Console Active OPC Server Settings Create
AOPC Tag, click the Create Tag button.
5. Launch Active OPC Server Lite from the Windows Start menu: Start
Programs MOXA IOServer ActiveOPC ActiveOPC.
Save configurations before exiting Active OPC Server Lite.
NOTE
A “load” in a circuit schematic is a component or portion of the
circuit that consumes electric power. For the diagrams shown in
this document, “load” refers to the devices or systems connected
to the remote I/O unit.
ATEX Information
1. Certificate number: DEMKO 13 ATEX 1210600X
2. Certification string: Ex nA nC IIC T3 Gc
3. Standards covered:
EN 60079-0:2012+A11:2013, EN 60079-15:2010
4. These products are to be installed in an ATEX Certified IP54
enclosure and accessible only by the use of a tool.
5. These products are for use in an area of not more than pollution
degree 2 in accordance with IEC 60664-1.