Moxa Technologies ioLogik E2200Series User manual

ioLogik E2200 Series User’s Manual
Edition 6.5, November 2016
www.moxa.com/product
© 2016 Moxa Inc. All rights reserved.

ioLogik E2200 Series User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2016 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction ...................................................................................................................................... 1-1
Product Key Features and Highlights .....................................................................................................1-2
Package Checklist ...............................................................................................................................1-2
Product Model Information...................................................................................................................1-2
Product Selection Guide.......................................................................................................................1-3
Product Specifications .........................................................................................................................1-4
Common Specifications ................................................................................................................1-4
ioLogik E2210 Specifications .........................................................................................................1-5
ioLogik E2212 Specifications .........................................................................................................1-6
ioLogik E2214 Specifications .........................................................................................................1-7
ioLogik E2240 Specifications .........................................................................................................1-8
ioLogik E2242 Specifications .........................................................................................................1-9
ioLogik E2260 Specifications ....................................................................................................... 1-10
ioLogik E2262 Specifications ....................................................................................................... 1-11
Physical Dimensions.......................................................................................................................... 1-12
Without LCM ............................................................................................................................. 1-12
With LCM ................................................................................................................................. 1-12
Hardware Reference.......................................................................................................................... 1-13
Panel Guide .............................................................................................................................. 1-13
Pin Assignments........................................................................................................................ 1-13
LED Indicators .......................................................................................................................... 1-14
2. Initial Setup ...................................................................................................................................... 2-1
Hardware Installation ..........................................................................................................................2-2
Connecting the Power ..................................................................................................................2-2
Grounding the Unit ......................................................................................................................2-2
Software Installation ...........................................................................................................................2-2
Restore Factory Defaults......................................................................................................................2-4
Connecting to ioAdmin via Ethernet ......................................................................................................2-4
Configuring the Host Computer’s IP Address ...................................................................................2-4
Activating ioAdmin and Connecting to the ioLogik............................................................................2-5
Adding More I/O Channels............................................................................................................2-8
Setting the RS-485 Baudrate ........................................................................................................2-9
I/O Wiring Diagrams ...........................................................................................................................2-9
Using ioAdmin to Import/Export Configurations .................................................................................... 2-11
3. Using ioAdmin ................................................................................................................................... 3-1
System Requirements .........................................................................................................................3-2
Features of ioAdmin ............................................................................................................................3-2
ioAdmin Overview...............................................................................................................................3-3
Main Screen Overview..................................................................................................................3-3
Title...........................................................................................................................................3-4
Menu Bar ...................................................................................................................................3-4
Quick Links............................................................................................................................... 3-10
Navigation Panel ....................................................................................................................... 3-10
Main Window ............................................................................................................................ 3-12
Sync Rate Status....................................................................................................................... 3-14
Status Bar ................................................................................................................................ 3-14
ioAdmin Administrator Functions ................................................................................................. 3-14
I/O Configuration Tab (Administrator) .......................................................................................... 3-15
Server Settings Tab (Administrator)............................................................................................. 3-28
Network Tab ............................................................................................................................. 3-29
Firmware Update Tab ................................................................................................................. 3-30
Watchdog Tab ........................................................................................................................... 3-31
Click&Go Logic Tab .................................................................................................................... 3-32
Active Tags Tab ......................................................................................................................... 3-33
SNMP Settings Tab .................................................................................................................... 3-36
Message Monitor Panel (General) ................................................................................................ 3-37
Server Context Menu ........................................................................................................................ 3-38
Using ioEventLog .............................................................................................................................. 3-40
Installing ioEventLog ................................................................................................................. 3-40
Basic Functions ......................................................................................................................... 3-40
Configuration ............................................................................................................................ 3-41
Checking Connected Devices ...................................................................................................... 3-42
Opening Log Files ...................................................................................................................... 3-42
Clearing the Log........................................................................................................................ 3-42
4. Click&Go ........................................................................................................................................... 4-1
Overview ...........................................................................................................................................4-2
Features ............................................................................................................................................4-2

Click&Go Logic Basics..........................................................................................................................4-3
Working with Rules .............................................................................................................................4-4
Click&Go Development Process.............................................................................................................4-4
I/O Configuration................................................................................................................................4-5
Digital Input Mode Selection .........................................................................................................4-5
Digital Output Mode Selection .......................................................................................................4-6
Analog Input Mode Selection.........................................................................................................4-6
Alias Name Configuration .............................................................................................................4-6
Testing the I/O Channels ..............................................................................................................4-7
Defining Global Variables .....................................................................................................................4-8
Internal Register (Integer) Settings ...............................................................................................4-8
Timer Settings ............................................................................................................................4-9
SNMP Trap Server .......................................................................................................................4-9
E-Mail Server ............................................................................................................................ 4-10
Active Message Server ............................................................................................................... 4-11
Working with Logic ........................................................................................................................... 4-12
Click&Go Logic Basics ................................................................................................................ 4-12
IF Conditions ............................................................................................................................ 4-14
THEN/ELSE Actions ........................................................................................................................... 4-18
Activating the Rule-set ...................................................................................................................... 4-27
Upload, Restart, and Run ........................................................................................................... 4-27
Rule-set Management Bar .......................................................................................................... 4-27
Import/Export Configuration .............................................................................................................. 4-27
More Information about Repeat Interval vs. Edge Detection ................................................................... 4-28
5. Using the Web Console...................................................................................................................... 5-1
Introduction to the Web Console...........................................................................................................5-2
Overview ...........................................................................................................................................5-3
Basic Settings ....................................................................................................................................5-3
Network Settings ................................................................................................................................5-4
General Settings .........................................................................................................................5-4
Ethernet Configurations ...............................................................................................................5-4
RS-485 Settings..........................................................................................................................5-4
I/O Settings .......................................................................................................................................5-5
DI Channels................................................................................................................................5-5
DO Channels...............................................................................................................................5-6
AI Channels................................................................................................................................5-8
Alias Name .................................................................................................................................5-8
AO Channels...............................................................................................................................5-9
Relay Output Channel ..................................................................................................................5-9
Relay Count Motoring................................................................................................................. 5-10
Alias Name set.......................................................................................................................... 5-11
RTD Channels ........................................................................................................................... 5-11
TC Channels ............................................................................................................................. 5-12
System Management......................................................................................................................... 5-13
Accessible IP Settings ................................................................................................................ 5-13
SNMP Agent ............................................................................................................................. 5-14
Network Connection .................................................................................................................. 5-14
Firmware Update....................................................................................................................... 5-14
Import System Config ................................................................................................................ 5-15
Export System Config ................................................................................................................ 5-15
LCM......................................................................................................................................... 5-15
Change Password ...................................................................................................................... 5-15
Load Factory Default.................................................................................................................. 5-16
Save/Restart............................................................................................................................. 5-16
6. Active OPC Server ............................................................................................................................. 6-1
Active OPC Server ..............................................................................................................................6-2
OLE for Process Control .......................................................................................................................6-2
Introduction to Active OPC Server.........................................................................................................6-3
Active OPC Server—From Pull to Push ...................................................................................................6-3
Features of Active OPC Server..............................................................................................................6-4
One Click to Create Active Tags .....................................................................................................6-4
Faster, More Accurate Data Collection than Traditional “Pull Technology”.............................................6-5
Active OPC Server Overview.................................................................................................................6-5
Installing Active OPC Server .........................................................................................................6-5
Main Screen Overview..................................................................................................................6-6
Menu Bar ...................................................................................................................................6-6
Tag Generation................................................................................................................................. 6-10
Configuring Push Tag from ioAdmin ............................................................................................. 6-10
Heartbeat Interval ..................................................................................................................... 6-11
Read/Write Privilege .................................................................................................................. 6-11
A. Liquid Crystal Display Module (LCM) ................................................................................................. A-1

LCM Controls......................................................................................................................................A-2
LCM Options.......................................................................................................................................A-2
B. Used Network Port Numbers ............................................................................................................. B-1
ioLogik E2200 Smart Ethernet Remote I/O Device Network Port Usage......................................................B-1
C. Factory Default Settings.................................................................................................................... C-1
D. Cable Wiring...................................................................................................................................... D-1
Device Wiring Diagrams ..................................................................................................................... D-2
Analog Input.............................................................................................................................. D-2
Analog Output ........................................................................................................................... D-2
Digital Input Dry Contact............................................................................................................. D-2
Digital Input Wet Contact ............................................................................................................ D-3
RTD Input Wiring ............................................................................................................................... D-5
Thermocouple Input Wiring ................................................................................................................. D-6
E. Input and Output Terminal................................................................................................................ E-1
ioLogik E2210 ....................................................................................................................................E-2
ioLogik E2212 ....................................................................................................................................E-2
ioLogik E2214 ....................................................................................................................................E-2
ioLogik E2240 ....................................................................................................................................E-3
ioLogik E2242 ....................................................................................................................................E-3
ioLogik E2260 ....................................................................................................................................E-3
ioLogik E2262 ....................................................................................................................................E-4
F. Accuracy ........................................................................................................................................... F-1
Calibration ......................................................................................................................................... F-1
Simple Verification at Your Site ............................................................................................................ F-1
Verification with RTD Sensor ......................................................................................................... F-1
Verification with Precision Resistor................................................................................................. F-1
G. CGI Commands.................................................................................................................................. G-1
ioLogik E2210 ................................................................................................................................... G-2
ioLogik E2212 ................................................................................................................................... G-6
ioLogik E2214 ..................................................................................................................................G-10
ioLogik E2240 ..................................................................................................................................G-12
ioLogik E2242 ..................................................................................................................................G-14
ioLogik E2260 ..................................................................................................................................G-19
ioLogik E2262 ..................................................................................................................................G-22
H. SNMP Agents with MIB II, RS-232-like Groups ............................................................................... H-1
ioLogik E2242 ................................................................................................................................... H-1
I. Modbus/TCP Address Mappings .........................................................................................................I-1
ioLogik E2210 Modbus Mapping ............................................................................................................ I-2
ioLogik E2212 Modbus Mapping ...........................................................................................................I-15
ioLogik E2214 Modbus Mapping ...........................................................................................................I-37
ioLogik E2240 Modbus Mapping ...........................................................................................................I-47
ioLogik E2242 Modbus Mapping ...........................................................................................................I-57
ioLogik E2260 Modbus Mapping ...........................................................................................................I-76
ioLogik E2262 Modbus Mapping ...........................................................................................................I-81

1
1. Introduction
The ioLogik E2200 series is a standalone Smart Ethernet remote I/O device that can connect sensors and
on/off switches for automation applications over Ethernet and IP-based networks.
The following topics are covered in this chapter:

Product Key Features and Highlights

Package Checklist

Product Model Information

Product Selection Guide

Product Specifications
Common Specifications
ioLogik E2210 Specifications
ioLogik E2212 Specifications
ioLogik E2214 Specifications
ioLogik E2240 Specifications
ioLogik E2242 Specifications
ioLogik E2260 Specifications
ioLogik E2262 Specifications

Physical Dimensions
Without LCM
With LCM

Hardware Reference
Panel Guide
Pin Assignments
LED Indicators

ioLogik E2200 Series Introduction
1-2
Product Key Features and Highlights
1. Front-end intelligence that supports 24 Click&Go rules
2. Active Messaging with real-time stamp, including SNMP Trap with I/O status, TCP, and e-mail.
3. Supports SNMPv1/v2c/v3 protocol
4. I/O peer-to-peer function
5. Built-in web console
6. PC utility: auto detection of installed modules
7. MXIO programming library for Windows, WinCE VB/VC.NET, and Linux C APIs
8. -40 to 75°C operating temperature range (T models)
Package Checklist
The ioLogik E2200 Series is shipped with the following items:
Standard Accessories
•ioLogik E22xx Smart Ethernet remote I/O device x1
Optional Accessories
•LDP1602 LCD Module
NOTE: Notify your sales representative if any of the above items are missing or damaged.
Product Model Information
Model Description
ioLogik E2210 Ethernet Remote IO with 12 DIs, 8 DOs, -10 to 60°C operating temperature
ioLogik E2212 Ethernet Remote IO with 8 DIs, 8 DOs, 4DIOs, -10 to 60°C operating temperature
ioLogik E2214 Ethernet Remote IO with 6 DIs, 6 relays, -10 to 60°C operating temperature
ioLogik E2240 Ethernet Remote IO with 8 AIs, 2 AOs, -10 to 60°C operating temperature
ioLogik E2242 Ethernet Remote IO with 4 AIs, 12 DIOs, -10 to 60°C operating temperature
ioLogik E2260 Ethernet Remote IO with 6 RTDs, 4 DOs, -10 to 60°C operating temperature
ioLogik E2262 Ethernet Remote IO with 8 TCs, 4 DOs, -10 to 60°C operating temperature
ioLogik E2210-T Ethernet Remote IO with 12 DIs, 8 DOs, -40 to 75°C operating temperature
ioLogik E2212-T Ethernet Remote IO with 8 DIs, 8 DOs, 4 DIOs, -40 to 75°C operating temperature
ioLogik E2214-T Ethernet Remote IO with 6 DIs, 6 Relays, -40 to 75°C operating temperature
ioLogik E2240-T Ethernet Remote IO with 8 AIs, 2 AOs, -40 to 75°C operating temperature
ioLogik E2242-T Ethernet Remote IO with 4 AIs, 12 DIOs, -40 to 75°C operating temperature
ioLogik E2260-T Ethernet Remote IO with 6 RTDs, 4 DOs, -40 to 75°C operating temperature
ioLogik E2262-T Ethernet Remote IO with 8 TCs, 4 DOs, -40 to 75°C operating temperature

ioLogik E2200 Series Introduction
1-3
Product Selection Guide
The operating temperature for standard models is -10 to 60°C.
The operating temperature for wide temperature models is -40 to 75°C
Digital
Inputs
Selectable
DIO
Digital
Outputs
Relay
Outputs
Analog
Inputs
Analog
Outputs
RTD
Inputs
TC
Inputs
E2200 Series Common Specification
E2210 12 8
E2212 8 4 8
E2214 6 6
E2240 8 2
E2242 12 4
E2260 4 6
E2262 4 8

ioLogik E2200 Series Introduction
1-4
Product Specifications
Common Specifications
LAN
Ethernet:
1 x 10/100 Mbps, RJ45
Protection:
1.5 kV magnetic isolation
Protocols:
Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP, HTTP, CGI, SNTP, SMTP
Serial Communication
Interface:
RS-485-2w: Data+, Data-, GND (3-contact terminal block)
Serial Line Protection:
15 kV ESD for all signals
Serial Communication Parameters
Parity:
None
Data Bits:
8
Stop Bits:
1
Flow Control:
None
Baudrate:
1200 to 115200 bps
Protocol:
Modbus/RTU
Power Requirements
Power Input:
24 VDC nominal, 12 to 36 VDC
Physical Characteristics
Wiring:
I/O cable max. 14 AWG
Dimensions:
115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weight:
under 250 g
Mounting:
DIN-rail or wall
Environmental Limits
Operating Temperature:
• Standard Models:
-10 to 60°C (14 to 140°F)
• Wide Temp. Models:
-40 to 75°C (-40 to 167°F)
Storage Temperature:
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity:
5 to 95% (non-condensing)
Altitude:
Up to 2000 m
Note: Please
contact Moxa if you require products guaranteed to function properly at higher altitudes.
Standards and Certifications
Safety:
UL 508
EMI:
EN 61000
-3-2; EN 61000-3-3; EN 61000-6-4;
FCC Part 15, Subpart B, Class A
EMS:
EN 61000
-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000
-4-5, EN 61000-4-6, EN 61000-4-8,
EN 61000
-4-11, EN 61000-6-2
Shock:
IEC 60068-2-27
Freefall:
IEC 60068-2-32
Vibration:
IEC 60068-2-6
Green Product:
RoHS, CRoHS, WEEE
Note: Please check Moxa’s website for the most up
-to-date certification status.
Warranty
Warranty Period:
5 years (excluding ioLogik E2214*)
*Because of the limited lifetime of power relays, products that use that component are covered by
a 2
-year warranty.
Details:
See www.moxa.com/warranty

ioLogik E2200 Series Introduction
1-5
ioLogik E2210 Specifications
Inputs and Outputs
Digital Inputs:
12 channels
Digital Outputs:
8 channels
Isolation:
3K VDC or 2K Vrms
Digital Input
Sensor Type:
Wet Contact (NPN), Dry Contact
I/O Mode:
DI or Event Counter
Dry Contact:
• On: short to GND
• Off:
open
Wet Contact (DI to GND):
• On: 0 to 3 VDC
• Off: 10 to 30 VDC
Common Type:
12 points per COM
Counter Frequency:
900 Hz
Digital Filtering Time Interval:
Software selectable
Digital Output
Type:
Sink
I/O Mode:
DO or Pulse Output
Pulse Output
Frequency: 1 kHz
Over
-voltage Protection: 45 VDC
Over
-current Protection: 2.6 A (4 channels @ 650 mA)
Over
-temperature Shutdown: 175°C (min.)
Current Rating:
200 mA per channel
Power Requirements
Power Consumption:
203 mA @ 24 VDC
MTBF (mean time between failure)
Time:
213,673 hrs
Database:
Telcordia (Bellcore)

ioLogik E2200 Series Introduction
1-6
ioLogik E2212 Specifications
Inputs and Outputs
Digital Inputs:
8 channels
Digital Outputs:
8 channels
Configurable DIOs:
4 channels
Isolation:
3K VDC or 2K Vrms
Digital Input
Sensor Type:
Wet Contact (NPN or PNP) and Dry Contact
I/O Mode:
DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (
DI to GND):
• On: 0 to 3 VDC
• OFF: 10 to 30 VDC
Common Type:
6 points per COM
Counter Frequency:
900 Hz, power off storage
Digital Filtering Time Interval:
Software selectable
Digital Output
Type:
Sink
I/O Mode:
DO or Pulse Output
Pulse Output Frequency:
1 kHz
Over
-voltage Protection: 45 VDC
Over
-current Protection: 2.6 A (4 channels @650 mA)
Over
-temperature Shutdown: 175°C (min.)
Current Rating:
200 mA per channel
Power Requirements
Power Consumption:
136 mA @ 24 VDC
MTBF
(mean time between failure)
Time:
217,722 hrs
Database:
Telcordia (Bellcore)

ioLogik E2200 Series Introduction
1-7
ioLogik E2214 Specifications
Inputs and Outputs
Digital Inputs:
6 channels
Relay Outputs:
6 channels
Isolation:
3K VDC or 2K Vrms
Digital Input
Sensor Type:
Wet Contact (NPN or PNP) and Dry Contact
I/O Mode:
DI or Event Counter
Dry Contact:
• On:
short to GND
• Off: open
Wet Contact
(DI to GND):
• On: 0 to 3 VDC
• Off: 10 to 30 VDC
Common Type:
3 points per COM
Counter Frequency:
900 Hz, power off storage
Digital Filtering Time Interval:
Software selectable
Relay Output
Type:
Form A (N.O.) power relay
Contact Current Rating:
• Inductive Load: 2 A @ 30 VDC, 250 VAC, 110 VAC
• Resistive Load: 5 A @ 30 VDC, 250 VAC, 110 VAC
Minimum permitted load:
1 A @ 5 VDC
Initial Insulation Resistance:
1000 M ohms (min.) @ 500 VDC
Mechani
cal endurance: 1,000,000 operations
Electrical endurance: 100,000 operations @ 5 A resistive load
Contact Resistance:
100 m ohms (max.)
Pulse Output:
0.3 Hz at rated load
Power Requirements
Power Consumption:
170 mA @ 24 VDC
MTBF (mean time between failure)
Time:
307,239 hrs
Database:
Telcordia (Bellcore)

ioLogik E2200 Series Introduction
1-8
ioLogik E2240 Specifications
Inputs and Outputs
Analog Inputs:
8 channels
Analog Outputs:
2 channels
Analog Input
Type:
Differential input
Resolution:
16 bits
I/O Mode:
Voltage / Current
Input Range:
±150 mV, ±500 mV, ±5 V, ±10 V, 0 to 20 mA, 4 to 20 mA
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @
-10 and 60°C
±0.5% FSR @
-40 and 75°C
Sampling Rate:
All channels:
• 10 samples/sec for voltage
• 6 samples/sec for current
Per
channel:
• 1.25 samples/sec for voltage
• 0.75 samples/sec for current
Single channel:
• 1.25 samples/sec for voltage
• 0.75 samples/sec for current
Input Impedance:
900K ohms (min.)
Built
-in Resistor for Current Input: 120 ohms
Isolation:
3K VDC or 2K Vrms
Analog Output
Resolution:
12 bits
Output Range:
0 to 10 V, 4 to 20 mA
Drive Voltage:
15 VDC for current output
Accuracy:
±0.1% FSR @ 25°C,
±0.3% FSR @
-10 and 60°C,
±0.5% FSR @
-40 and 75°C
Load Resistor:
Less than 250 ohms
Power Requirements
Power Consumption:
198 mA @ 24 VDC
MTBF (mean time between failure)
Time:
155,941 hrs
Database:
Telcordia (Bellcore)

ioLogik E2200 Series Introduction
1-9
ioLogik E2242 Specifications
Inputs and Outputs
Analog Inputs:
4 channels
Configurable DIOs:
12 channels
Analog Input
Type:
Differential input
Resolution:
16 bits
I/O Mode:
Voltage / Current
Input Range:
±150 mV, 0 to 150 mV, ±500 mV, 0 to 500 mV, ±5 V, 0 to 5 V, ±10 V, 0 to 10 V, 0 to 20 mA,
4 to 20 mA
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @
-10 and 60°C
±0.5% FSR @
-40 and 75°C
Sampling Rate:
All channels:
• 32 samples/sec
Per channel:
• 8 samples/sec
Single channel:
• 100 samples/sec
Input Impedance:
200K ohms (min.)
Built
-in Resistor for Current Input: 120 ohms
Digital Input
Sensor Type:
Wet Contact (NPN or PNP) and Dry Contact
I/O Mode:
DI or event counter
Dry Contact:
• On: short to GND
• Off: Open
Wet Contact
(DI to GND):
• On: 0 to 3 VDC
• Off: 10 to 30 VDC
Common Type:
6 points per COM
Isolation:
3K VDC or 2K Vrms
Counter
Frequency: 900 Hz, power off storage
Digital Filtering Time Interval:
Software selectable
Digital Output
Type:
Sink
I/O Mode:
DO or Pulse Output
Pulse Output Frequency:
1 kHz
Over
-voltage Protection: 45 VDC
Over
-current Protection: 2.6 A (4 channels @ 650 mA)
Over
-temperature Shutdown: 175°C (min.)
Current Rating:
200 mA per channel
Isolation:
3K VDC or 2K Vrms
Power Requirements
Power Consumption:
178 mA @ 24 VDC
MTBF (mean time between failure)
Time:
204,391 hrs
Database:
Telcordia (Bellcore)

ioLogik E2200 Series Introduction
1-10
ioLogik E2260 Specifications
Inputs and Outputs
RTD Inputs:
6 channels
Digital Outputs:
4 channels
Isolation:
3K VDC or 2K Vrms
RTD Inputs
Input Type:
PT50, PT100, PT200, PT500, PT1000; JPT100, JPT200, JPT500, JPT1000; NI100, NI120, NI200,
NI500, NI1000; Resistance of 310, 620, 1250, and 2200 ohms
Sampling Rate:
12 samples/sec (all channels)
Resolution:
0.1°C or 0.1 ohm
Accuracy:
±0.1% FSR @ 25°C
±0.
3% FSR @ -10 and 60°C
±0.5% FSR @
-40 and 75°C
Input Impedance:
625K ohms
Digital Output
Type:
Sink
I/O Mode:
DO or Pulse Output
Pulse Output Frequency:
100 Hz
Over
-voltage Protection: 45 VDC
Over
-current Protection: 2.6 A (4 channels @ 650 mA)
Over
-temperature Shutdown: 175°C
Current Rating:
200 mA per channel
Power Requirements
Power Consumption:
95 mA @ 24 VDC
MTBF (mean time between failure)
Time:
327,282 hrs
Database:
Telcordia (Bellcore)

ioLogik E2200 Series Introduction
1-11
ioLogik E2262 Specifications
Inputs and Outputs
Thermocouple Inputs:
8 channels
Digital Outputs:
4 channels
Thermocouple Input
Sensor Type:
J (0 to 750°C), K (-200 to 1250°C), T (-200 to 350°C), E (-200 to 900°C), R (-
50 to 1600°C),
S (
-50 to 1760°C), B (600 to 1700°C), N (-200 to 1300°C)
Millivolt Type:
• Mode: ±78.126 mV, ±39.062 mV, ±19.532 mV
• Fault and over
-voltage protection: -35 to +35 VDC (power off); -25 to +30 VDC (power on)
Sampling Rate:
12 samples/sec (all channels)
Resolution:
16 bits
Accuracy:
±0.1% FSR @ 25°C
±0.3% FS
R @ -10 and 60°C
±0.5% FSR @
-40 and 75°C
Input Impedance:
1 M ohms
Digital Output
Type:
Sink
I/O Mode:
DO or Pulse Output
Pulse Output Frequency:
100 Hz
Over
-voltage Protection: 45 VDC
Over
-current Protection: 2.6 A (4 channels @ 650 mA)
Over
-temperature Shutdown: 175°C
Current Rating:
200 mA per channel
Isolation:
3K VDC or 2K Vrms
Power Requirements
Power Consumption:
160 mA @ 24 VDC
MTBF
(mean time between failure)
Time:
341,063 hrs
Database:
Telcordia (Bellcore)

ioLogik E2200 Series Introduction
1-12
Physical Dimensions
Without LCM
Unit = mm
With LCM
Unit = mm

ioLogik E2200 Series Introduction
1-13
Hardware Reference
Panel Guide
NOTE
The RESET button restarts the device and resets all settings to factory defaults. Use a pointed object such as
a straightened paper clip to hold the RESET button down for 5 sec. The RDY LED will turn red as you are holding
the RESET button down. The factory defaults will be loaded once the RDY LED turns green again. At this point
you can release the RESET b
utton.
Pin Assignments
System Bus
Pin 1 2 3 4 5
Signal V+ V- V+ V- NC
Pin 6 7 8 9 10
Signal NC Data+ SYNC Data- GND
Ethernet Port
Pin 1 2 3 4
Signal TXD+ TXD- RXD+ ---
Pin 5 6 7 8
Signal --- RXD- --- ---
TB1
TB2

ioLogik E2200 Series Introduction
1-14
TB1 (Power Input & RS-485 Connector)
Pin 1 2 3 4 5 6
Signal V+ V- FG D+ D- SG
(V+: 12 to
36 VDC)
TB2 (Input and Output Terminal)
Refer to the Appendix F.
LED Indicators
LED Light Description
PWR Off System power off
Red System power on
RDY Off System not ready
Green System ready
Red System error
Green Blinking Click & Go running
Green/Red Blinking System in Safe mode
Serial Off Serial port not connected
Red Serial port connected
Blinking Data sending and receiving
Ethernet Off Ethernet port not connected
Amber 10 Mbps connected
Green 100 Mbps connected
Blinking Data sending and receiving
DI Off DI status off
Green DI status on
DO Off DO status off
Red DO status on
DIO Off DI or DO status off
Green DI mode and status on
Amber DO mode and status on
AI Off AI channel disabled
Transmitter not connected when 4-20 mA mode
Green AI channel enabled
RTD Green RTD status on
Red RTD transmitter not connected
TC Green TC status on
Red TC transmitter not connected
DO Power Off External power off or not connected
Red External power on

2
2. Initial Setup
This chapter describes how to install the ioLogik E2200 series.
The following topics are covered in this chapter:

Hardware Installation
Connecting the Power
Grounding the Unit

Software Installation

Restore Factory Defaults

Connecting to ioAdmin via Ethernet
Configuring the Host Computer’s IP Address
Activating ioAdmin and Connecting to the ioLogik
Adding More I/O Channels
Setting the RS-485 Baudrate

I/O Wiring Diagrams

Using ioAdmin to Import/Export Configurations