Moxa Technologies NPort 6450 Series User manual

P/N: 1802064500015
*1802064500015*
NPort 6450 Series
Quick Installation Guide
Edition 8.0, August 2016
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2016 Moxa Inc. All rights reserved.

- 2 -
Overview
The NPort 6450 secure serial device servers provide reliable
serial-to-Ethernet connectivity for a wide range of serial devices. The
NPort 6450 supports TCP Server, TCP Client, UDP, and Pair-Connection
operation modes to ensure the compatibility of network software. In
addition, the NPort 6450 also supports Secure TCP Server, Secure TCP
Client, Secure Pair-Connection, and Secure Real COM modes for security
critical applications such as banking, telecom, access control, and remote
site management.
Package Checklist
Before installing the NPort 6450, please verify that the package contains
the following items:
•1 NPort 6450
•Power adaptor (does not apply to T models)
•2 wallmount ears
•Quick installation guide
•Documentation and software CD
•Warranty card
Optional Accessories
•DK-35A: 35 mm DIN-rail mounting kit
•DIN-rail power supply
•CBL-RJ45M9-150: 8-pin RJ45 to male DB9 cable
•CBL-RJ45M25-150: 8-pin RJ45 to male DB25 cable
•NM-TX01: Network module with one 10/100BaseTX Ethernet port
(RJ45 connector; supports cascade redundancy and RSTP/STP)
•NM-FX01-S-SC/NM-FX01-S-SC-T: Network module with one
100BaseFX single mode fiber port (SC connector; supports cascade
redundancy and RSTP/STP)
•NM-FX02-S-SC/NM-FX02-S-SC-T: Network module with two
100BaseFX single mode fiber ports (SC connectors; supports cascade
redundancy and RSTP/STP)
•NM-FX01-M-SC/NM-FX01-M-SC-T: Network module with one
100BaseFX multi-mode fiber port (SC connector; supports cascade
redundancy and RSTP/STP)
•NM-FX02-M-SC/NM-FX02-M-SC-T: Network module with two
100BaseFX multi-mode fiber ports (SC connectors; supports cascade
redundancy and RSTP/STP)
NOTE
Please notify your sales representative if any of the above items
are missing or damaged.

- 3 -
Hardware Introduction
NOTE
The LCD panel is only available with standard temperature
models.
Reset Button—Press the Reset button continuously for 5 sec to load
factory defaults. Use a pointed object, such as a straightened paper clip or
toothpick, to press the reset button. This will cause the Ready LED to blink
on and off. The factory defaults will be loaded once the Ready LED stops
blinking (after about 5 seconds). At this point, you should release the
reset button.
LED Indicators
Name
Color
Function
PWR
Red
Power is being supplied to the power input.
Ready Red
Steady on:
NPort is booting up.
Blinking: IP conflict, DHCP or BOOTP server
problem, or relay output problem.
Green
Steady on:
Power is on and the NPort 6450 is
functioning normally.
Blinking:
NPort is responding to Locate
function.
Off
Power is off, or power error condition exists.
Link
Orange
10 Mbps Ethernet connection.
Green
100 Mbps Ethernet connection.
Off
Ethernet cable is disconnected, or has a short.
P1-P4
Orange
Serial port is receiving data.
Green
Serial port is transmitting data.
Off
Serial port is idle.

- 4 -
Name
Color
Function
FX
Orange
Steady on:
Ethernet port is idle.
Blinking:
Fiber port is transmitting or
receiving data.
Alarm
Red
The relay output (DOUT) is open (exception).
Off
The relay output (DOUT) is shorted (normal
condition).
Module
Green
A network module has been detected.
Off
No network module is present.
Adjustable pull high/low resistor for RS-422/485 (150
KΩor 1 KΩ)
Jumpers are used to set the
pull high/low resistors. The
default is 150 KΩ. Short the
jumpers to set this value to 1
KΩ. Do not use the KΩ setting
with RS
-232 mode, since
doing so will degrade the
RS
-232 signals and shorten
the communication
distance.
Hardware Installation Procedure
STEP 1: Connect the 12-48 VDC power adaptor to the NPort 6450 and
then plug the power adaptor into a DC outlet.
STEP 2: For first-time configuration, use a cross-over Ethernet cable to
connect the NPort 6450 directly to your computer’s Ethernet cable. For
connecting to a network, use a standard straight-through Ethernet cable
to connect to a hub or switch.
STEP 3: Connect the NPort 6450’s serial port(s) to serial device(s).
Placement Options
The NPort 6450 can be placed flat on a desktop or other horizontal surface.
In addition, you may use the DIN-Rail or Wall Mount options, as
illustrated below.
Wallmount
DIN Rail

- 5 -
Software Installation Information
The Document & Software CD contains the User’s Manual, NPort Search
Utility, and the PComm Lite Suite. Insert the CD and follow the on-screen
instructions. Please refer to the User’s Manual for additional details on
using the NPort Search Utility and PComm Lite.
Pin Assignments and Cable Wiring
RS-232/422/485 Pin Assignments (male DB9)
Pin RS-232
RS-422/
4W RS-485
2W RS-485
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
Specifications
LAN
Ethernet
10/100 Mbps, RJ45
Protection
Built-in 1.5 KV magnetic isolation
Optical Fiber (for fiber port modules)
Distance Multi-mode:
0 to 2 km, 1310 nm (62.5/125 μm, 500 MHz*km)
Single mode:
0 to 40 km, 1310 nm (9/125 μm, 3.5 PS/(nm*km)
Min. TX Output
Multi-mode: -20 dBm; Single mode: -5 dBm
Max. TX Output
Multi-mode: -10 dBm; Single mode: 0 dBm
Sensitivity
Multi-mode: -34 to -30 dBm,
Single mode: -36 to -32 dBm
Serial
Interfaces
RS-232/422/485 (male DB9)
No. of Ports
4
Serial Communication Parameters
Parity
None, Even, Odd, Space, Mark
Data Bits
5, 6, 7, 8
Stop Bit(s)
1, 1.5, 2
Flow Control
RTS/CTS, XON/XOFF, DTR/DSR
Speed
50 bps to 921.6 kbps
Additional Features
Console Port
RS-232 (see the user’s manual for detailed operating
instructions)
Memory
One SD socket
Software Features
Protocols
ICMP, IPv4/v6, TCP, UDP, DHCP, BOOTP, Telnet, DNS,
SNMP, DDNS, HTTP, SMTP, HTTPS, SSL, SSH, PPPoE
Utilities
Windows utility for Windows 98, ME, NT, 2000, XP,
2003, Vista, 8, XP x64, 2003 x64, Vista x64, 2012 x64
Security
DES/3DES/AES

- 6 -
OS Driver
Support
Windows Real COM Drivers: Windows
95/98/ME/NT/2000, Windows
XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows
2008 R2/2012/2012 R2 (x64), Windows Embedded
CE
5.0/6.0, Windows XP Embedded
Real TTY drivers: Linux 2.4, 2.6, and 3.x
Fixed TTY drivers: SCO Unix, SCO OpenServer 5,
OpenServer 6, UnixWare 7, UnixWare 2.1, SVR4.2,
QNX 4.25, QNX 6, Solaris 10, FreeBSD 5, FreeBSD 6
Configuration
Web Console, Serial/Telnet Console, Windows utility
Power Requirements
Power Input
12 to 48 VDC
Mechanical Specifications
Material
SECC sheet metal (1 mm)
Environmental Limits
Operating
Temperature
NPort 6450: 0 to 50°C (32 to 122°F)
NPort 6450-T: -40 to 75°C (-40 to 167°F)
Storage
Temperature
NPort 6450: 0 to 55°C (32 to 131°F)
NPort 6450-T: -20 to 75°C (-4 to 167°F)
Regulatory Approvals
EMC
FCC Class A, CE Class A
Safety
UL, CUL, TUV