Moxa Technologies NPort 6650 User manual

– 1 – – 2 – – 3 –
P/N: 1802066500015
*1802066500015*
NPort 6600 Series
Quick Installation Guide
Sixth Edition, August 2015
Overview
The NPort 6600 series of serial device servers includes 8-port,
16-port, and 32-port models for connecting larger numbers of
serial devices to Ethernet. Some applications now also require
better security when transmitting data through a network. The
NPort 6600 series of device servers use DES, 3DES, and AES data
encryption to provide secure network communication.
Package Checklist
Before Installing your NPort 6600 series secure device server,
verify that the package contains the following items:
•1 NPort 6600 device server
•CBL-RJ45M9-150: 8-pin RJ45 to DB9 male connection cable,
150 cm
•Power Cord (AC models only)
•2 rack-mount ears
•Documentation and software CD
•Quick installation guide (printed)
•Warranty card
Optional Accessories
•DK-35A: 35 mm DIN-Rail Mounting Kit
•DIN-Rail Power Supply
•NM-TX01/NM-TX01-T: Network module with one
10/100BaseTX Ethernet port (RJ45 connector; supports
cascade redundancy)
•NM-FX01-S-SC/NM-FX01-S-SC-T: Network module with one
100BaseFX single mode fiber port (SC connector; supports
cascade redundancy)
•NM-FX02-S-SC/NM-FX02-S-SC-T: Network module with two
100BaseFX single mode fiber ports (SC connectors; supports
cascade redundancy)
•NM-FX01-M-SC/NM-FX01-M-SC-T: Network module with one
100BaseFX multi mode fiber port (SC connector; supports
cascade redundancy)
•NM-FX02-M-SC/NM-FX02-M-SC-T: Network module with two
100BaseFX multi mode fiber ports (SC connectors; supports
cascade redundancy)
NOTE: Please notify your sales representative if any of the above
items is missing or damaged.
Hardware Introduction
Demonstrated 8 port model to be an example.
Reset Button
Press the Reset button continuously for 5 sec to load factory
defaults: Use a pointed object to press the reset button. Release
the button after the Ready LED stops blinking.
RS-485 adjustable pull high/low resistor (150/1 kO)
The NPort 6650 has 3 DIP Switches associated with each serial port
for configuring the pull high/low resistors for RS-485 applications.
The switches are located in a recess on the bottom of the NPort
6650. To access the switches, first remove the panel covering the
recess.
SW
1
2
3
Pull High
Pull Low
Terminator
ON
1 KΩ
1 KΩ
120 KΩ
OFF
150 KΩ
150 KΩ
–
NOTE: For RS-232 applications, all DIP Switches for the port
should be set to the OFF position.
Rack Mounting
Use four screws to attach the NPort 6610/6650 to a standard rack
LED Indicators
Name
Color
Function
PWR
Red
Power is being supplied to the power input.
Ready
Red
Steady
on:
Power is on and the NPort 6600
series is booting up.
Blinking:
IP conflict, DHCP or BOOTP server
not responding, or relay output.
Check relay output first. If still
blinking, then there is an IP
conflict, or the DHCP or BOOTP
server did not respond properly.
Green
Steady
on:
Power is on and the NPort 6600
series is functioning normally.
Blinking:
The device server has been
located by the Administrator’s
Locator function.
Off Power is off, or power error condition exists.
Link Orange 10 Mbps Ethernet connection.
Green
100 Mbps Ethernet connection.
Off
Ethernet cable is disconnected, or has a
short.
P1-P16 Tx
Green
Serial port is transmitting data.
Off
No data is being transmitted through the
serial port
P1-P16 Rx
Orange
Serial port is receiving data..
Off
No data is being received through the serial
port.
FX
Orange
Steady
on:
Ethernet fiber connection, but port
is idle.
Blinking:
Fiber port is transmitting or
receiving data.
P1-P16
in-use
LEDs
Green
Serial port is opened by server side
software.
Off
Serial port is not opened by server side
software.
Alarm
Red
The relay Dout is open (exception)
Off
The relay Dout is Shorted (normal)
Module
Green
Network module is plugged in and detected
Off
No module present
LCM Display Panel
The NPort 6600 display panel will show the model name, server
name, and IP address when powered up
N
P
6
6
1
0
_
6
6
1
0
2
1
9
2
.
1
6
8
.
1
2
7
.
2
5
4

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific:
[phone]
China:
[phone] (toll-free: 800-820-5036)
2014 Moxa Inc., All Rights Reserved
Operating the LCM Panel
There are four push buttons on the NPort 6600’s top panel for
operating the server’s LCM panel. The function of each button is
described below:
Button
Action
MENU
Activates the main menu, or returns to a lower level.
∧
Scrolls up through a list of items shown on the LCM panel’s
second line.
∨
Scrolls down through a list of items shown on the LCM
panel’s second line.
SEL
Selects the option listed on the LCM panel’s second line.
Detailed LCM panel operating instructions can be found on the
Document and Software CD in the “NPort 6600 Series User’s
Manual.”
Note: LCM display panel and push buttons only for standard
temprature model
Hardware Installation Procedure
STEP 1: Connect the NPort 6600 device server to a suitable power
source.
AC models: Connect the 100 to 240 VAC power cord to the NPort
6600’s power input.
DC models: Connect the terminal block to a battery.
STEP 2: Connect the NPort 6600 series to a network. Use a
standard straight-through Ethernet cable to connect to a hub or
switch. Use a cross-over Ethernet cable when connecting to your
computer’s Ethernet port (e.g., when setting up or testing the
NPort 6600 server).
STEP 3: Connect the NPort 6600’s serial ports to your serial
devices.
Software Installation Information
NPort Search Utility
To install the NPort Search Utility, insert the NPort Document and
Software CD into your computer’s CD-ROM drive. When the NPort
Installation CD window opens, click on the Installation button, and
then follow the instructions on the screen. To view detailed
information about the NPort Search Utility, refer to the pdf version
of the “NPort 6600 Series User’s Manual,” which is located in the
document directory of the CD.
PComm Lite and Console Port (19200, 8, None, 1)
MOXA’s PComm Lite software utility is also included in the
Document and Software CD of the CD-ROM. PComm Lite is often
used to connect to the NPort 6600 through its console port to
configure the IP address for the first time. Use the following serial
console parameters when connecting through the console port:
19200, 8, None, 1.
Pin Assignments and Cable Wiring
Pin Assignments (NPort 6610/6650)
Pin
RS-232
RS-422,
4-wire RS -485
2-wire RS-485
1
DSR
–
–
2
RTS
TxD+
–
3
GND
GND
GND
4
TxD
TxD-
–
5
RxD
RxD+
Data+
6
DCD
RxD-
Data-
7
CTS
–
–
8
DTR
–
–
Pin Mapping for RS-232 Cables (NPort 6610/6650)
NPort6610/6650
Serial Device
RJ45
DB9(M)
DB9(F)
DB25(M)
DB25(F)
DSR
1
6
4
6
20
DTR
RTS
2
7
8
4
5
CTS
GND
3
5
5
7
7
GND
TxD
4
3
2
2
3
RxD
RxD
5
2
3
3
2
TxD
DCD
6
1
1
8
8
DCD
CTS
7
8
7
5
4
RTS
DTR
8
4
6
20
6
DSR
Pin Mapping for RS-422/4W-RS-485 Cables (NPort 6650)
NPort 6650
Serial Device
RJ45
DB9(M)
DB9(F)
DB25(M)
DB25(F)
TxD+
2
7
8
4
5
RxD+
GND
3
5
5
7
7
GND
TxD-
4
3
2
2
3
RxD-
RxD+
5
2
3
3
2
TxD+
RxD-
6
1
1
8
8
TxD-
Pin Mapping for 2W-RS-485 Cables (NPort 6650)
NPort 6650
Serial Device
RJ45
DB9(M)
DB9(F)
DB25(M)
DB25(F)
GND
3
5
5
7
7
GND
Data+
5
2
3
3
2
Data+
Data-
6
1
1
8
8
Data-
Specifications
LAN
Ethernet Ports
10/100 Mbps (RJ45)
Protection
Built-in 1.5 KV magnetic isolation
Serial Interface
NPort 6610
NPort 6650
8, 16, or 32 RS-232 ports (8-pin RJ45)
8, 16, or 32 RS-232/422/485 ports (8-pin RJ45)
Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD,
GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485(2W): Data+, Data-, GND
RS-485(4W): Tx+, Tx-, Rx+, Rx-, GND
RS-485 Data
Direction
ADDC™ (Automatic Data Direction Control)
Serial Communication Parameters
Parity
None, Even, Odd, Space, Mark
Data bits
5, 6, 7, 8
Stop bit(s)
1, 1.5, 2
Flow control
RTS/CTS, XON/XOFF, DTR/DSR
Speed
50 bps to 921.6 Kbps
Console port
RS-232 console × 1
Memory Expansion Slot
Slot Type
SD socket (supports up to 2 GB)
Power Requirements
Power input
100 to 240 VAC, 47 to 63 Hz, 88 to 300 VDC,
±48 VDC (20 to 72 VDC, -20 to -72 VDC)
Alarm Contact
Relay output with current carrying capacity of 1A
@ 24 VDC
Mechanical Specifications
Material
SECC sheet metal (1 mm)
Dimensions
(W×D×H)
480×44×195 mm (including ears)
440×44×195 mm (without ears)
Operating Temperatures
Standard Temp. Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
High Voltage Wide Temp. Models: -40 to 85°C (-40 to 185°F)
Storage Temperatures
Standard and Wide Temp. Models: -40 to 75°C (-40 to 167°F)
High Voltage Wide Temp. Models: -40 to 85°C (-40 to 185°F)
Regulatory Approvals
EMC
FCC Class A, CE Class A
Safety
UL, CUL, EN 60950-1