Moxa Technologies VPort 2110 User manual

MOXA VPort 2110/2140/2141
Video Server
Quick Installation Guide
Third Edition, July 2006
MOXA Networking Co., Ltd.
Tel: [phone]
Fax: [phone]
www.moxa.com
[e-mail] (Worldwide)
[e-mail] (The Americas)
NOTE: This Quick Installation Guide describes basic installation
procedures for VPort 2110/2140/2141 Video Servers. Please refer to
the User’s Manual on the documentation CD for more detailed
instructions about using these products.
P/N: 1802021100200

MOXA VPort 2110/2140/2141
Video Server Quick Installation Guide
The software described in this manual is furnished under a license
agreement and may be used only in accordance with the terms of that
agreement.
Copyright Notice
Copyright ©2006 MOXA Networking Co., Ltd.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
MOXA is a registered trademark of The Moxa Group.
All other trademarks or registered marks in this manual belong to their
respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does
not represent a commitment on the part of Moxa.
Moxa provides this document “as is,” without warranty of any kind, either
expressed or implied, including, but not limited to, its particular purpose.
Moxa reserves the right to make improvements and/or changes to this
manual, or to the products and/or the programs described in this manual, at
any time.
Information provided in this manual is intended to be accurate and reliable.
However, Moxa Technologies assumes no responsibility for its use, or for
any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors.
Changes are periodically made to the information herein to correct such
errors, and these changes are incorporated into new editions of the
publication

1
1
Chapter 1 Package Checklist
VPort 2110 Video Server
Standard Accessories
y1 VPort 2110 Video Server
yPower adapter
¾Input: 100 to 240 VAC
¾Output: +12 VDC, 1.5A (UK Standard: +12 VDC, 1.25A)
yPTZ Camera Control Cable
yNull Modem Cable (Female DB9 to Female DB9)
yI/O Terminal Block Kit for
¾1 DI, 1 Relay Output
¾1 RS-485 COM port
yQuick Installation Guide
ySoftware CD
yWrench and Pad
yWarranty Card
Optional Accessories (must be ordered separately)
yDIN-Rail Mounting Kit DK-35A

VPort 2110/2140/2141 Quick Installation Guide
1-2
VPort 2140 Video Server
Standard Accessories
y1 VPort 2140 Video Server
yPower adapter
¾Input: 100 to 240 VAC
¾Output: +12 VDC, 1.5A (UK Standard: +12 VDC, 1.25A)
yPTZ Camera Control Cable
yNull Modem Cable (Female DB9 to Female DB9)
yI/O Terminal Block Kit ×2 for
¾4 DI, 2 Relay Outputs
¾1 RS-485 COM port
¾1 12 VDC Power Output (Max. 500 mA)
¾1 External Power Input (12 VDC, Min. 1.5A)
yQuick Installation Guide
ySoftware CD
yL-type Fixed Aluminum piece and 8 screws
yWarranty Card
VPort 2141 Video Server
Standard Accessories
y1 VPort 2141 Video Server
yPower adapter
¾Input: 100 to 240 VAC
¾Output: +12 VDC, 1.5A (UK Standard: +12 VDC, 1.25A)
yPTZ Camera Control Cable
yI/O Terminal Block Kit ×2 for
¾4 DI, 4 Relay Outputs
¾1 RS-485 COM port
¾1 12 VDC Power Output (Max. 500 mA)
¾1 External Power Input (12-15 VDC/VAC, Min. 1.5A)
yQuick Installation Guide
ySoftware CD
yPanel Mounting Kit with 4 screws
yPad
yWarranty Card
Optional Accessories (must be ordered separately)
yDIN-Rail Mounting Kit DK-35A

2
2
Chapter 2 Product Description
Panel Layout
VPort 2110 Video Server
Front Panel
1. BNC video input
Rear Panel
2. 12 VDC power input
3. Network and status LEDs
4. GPIO terminal block for
DI, DO, relay, and RS-485
COM port
5. “Restore default setting”
button
6. RJ45 10/100 Mbps
Ethernet connector
7. RS-232 COM port

VPort 2110/2140/2141 Quick Installation Guide
2-2
VPort 2140 Video Server
Front Panel
1. Reset & default buttons for restoring the system
2. BNC video output (switch on the 75ΩDIP switch)
3. BNC video input
4. Video/camera number
5. 75Ωresistance DIP Switch
6. System status LEDs
7. Network status LEDs
Rear Panel
8. RS-232 COM port for connecting PTZ camera
9. GPIO terminal block PIN description
10. RJ45 10/100 Mbps Ethernet connector
11. RS-232 COM port for connecting modem or PTZ camera
12. GPIO terminal block for DI, DO, relay, RS-485 COM port,
12 VDC power input and output
13. 12 VDC power input

Product Description
2-3
VPort 2141 Video Server
Front Panel
OFF
ON
75
1234
RESET
POWER
CONNECT
SERIAL
ACTIVE
LINK
FDX
VIDEO 2VIDEO 1 VIDEO 4VIDEO 3
22
33 1 4
5
6
1. Reset button for restoring the default configuration
2. BNC Video Input (switch off the 75ΩDIP switch)
3. Video/Camera Number
4. 75Ωresistance DIP Switches
5. System Status LEDs
6. Network Status LEDs
Rear Panel
COM 1
(RS-232)
10/100 Mbps
Ethernet
Power OUT: 12 VDC Relay 1
NO C NC NO C NC
1
Relay 2 D 1ID 2IRS-485
13
14
13
26
POWER IN
12 VDC
2 3 4 5 6 7 8 9 10 11 12
Power IN: 12-15V DC/AC Relay 3
NO C NC NO C NC
14
Relay 4 D 3ID 4IRS-485
2615 16 17 18 19 20 21 22 23 24 25
123 4 56 789101112
15 16 17 18 19 20 21 22 23 24 25
791011 8
7. RS-232 COM port for connecting PTZ camera
8. GPIO Terminal Block PIN description
9. RJ45 10/100 Mbps Ethernet connector
10. GPIO Terminal Block for DI, DO, relay, RS-485 COM port,
12 VDC power input and output
11. 12 VDC Power Input