Moxa Technologies EDS-2008-EL Series User manual

P/N: 1802020080010
*1802020080010*
EDS-2008-EL/ELP Series
Quick Installation Guide
Moxa EtherDevice Switch
Version 1.0, October 2019
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2019 Moxa Inc. All rights reserved.

- 2 -
Overview
The EDS-2008-EL/ELP Series has an 8-port combination to simplify
network expansion. There are two housing types available for the user
to select depending on the requirements of their application. The ELP
has a plastic housing and the EL has a metal housing. The compact
switches provide a cost-effective solution for your industrial Ethernet
connection requirements.
The EDS-2008-EL/ELP Series provides 12/24/48 VDC (9.6 to 60 VDC)
power input, and the switches are available with a standard operating
temperature range from -10 to 60°C, or with a wide operating
temperature range from -40 to 75°C (only available for the –T models
in the EL Series). The switches are rugged enough to operate reliably in
harsh industrial environments.
To provide greater versatility for use with applications from different
industries, the EDS-2008-EL/ELP Series also allows users to enable or
disable broadcast storm protection (BSP), Quality of Service (QoS)
function via the DIP switches on the top panel.
The EDS-2008-EL/ELP switches can be easily installed with DIN-rail
mounting as well as distribution boxes. The DIN-rail mounting
capability and IP40 housing with LED indicators ensure that the plug-
and-play EDS-2008-EL/ELP switches are reliable and easy to use.
NOTE
Throughout this Quick Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch:
EDS = Moxa EtherDevice Switch
ATTENTION
This device complies with part 15 of FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept
any
interference received, including interference that may
cause undesired operations.
Package Checklist
Your EDS is shipped with the following items. If any of these items are
missing or damaged, please contact your customer service
representative for assistance.
•Moxa EtherDevice™ Switch
•Quick installation guide (printed)
•Warranty card

- 3 -
Features
High Performance Network Switching Technology
•10/100BaseT(X) auto-negotiation speed, full/half duplex mode,
auto MDI/MDI-X connection, and 100BaseFX for fiber port models.
•IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X).
•IEEE 802.1p for Quality of Service (QoS) traffic prioritized function.
•Store-and-forward switching process type.
Industrial-grade Reliability
•Broadcast storm protection to prevent network devices from
crashing
Rugged Design
•Operating temperature range from -10 to 60°C, or extended
operating temperature from -40 to 75°C (only available for the –T
models in the EL Series)
•IP40, rugged high-strength case
•DIN-rail or panel mounting ability
WARNING
The
power for this product is intended to be supplied by a
Listed Power Supply, with output marked LPS, and rated to
de
liver 12 to 48 VDC at a maximum of 0.25 A.
The DC
jack should be used with an LPS unit that is rated to
deliver 12 to 48 VDC at a minimum of
1.1 A. The product
should not be disassembled by operators or service people.

- 4 -
Panel Layout of EDS-2008-EL/EDS-2008-ELP
1. Chassis ground screw
2. Terminal block for power input
3. DIP switch
4. Power LED
5. 10/100 BaseT(X) Port
6. 10/100 BaseT(X) Port LED
7. Port number
8. Model name

- 5 -
Panel Layout of EDS-2008-EL-M-ST/
EDS-2008-EL-M-SC
1. Chassis ground screw
2. Terminal block for power input
3. DIP switch
4. Power LED
5. 10/100 BaseT(X) Port
6. 10/100 BaseT(X) Port LED
7. Port number
8. 10/100 BaseFX Multi-mode ST Port (only for ST models)
9. 10/100 BaseFX Multi-mode SC Port (only for SC models)
10. 10/100 BaseFX Port LED
11. Model name

- 6 -
Mounting Dimensions
EDS-2008-EL Series
EDS-2008-ELP Series

- 7 -
EDS-2008-EL-M-ST Series
EDS-2008-EL-M-SC Series

- 8 -
DIN-rail Mounting
When shipped, the DIN-rail mounting kit is fixed to the back panel of
the EDS. Mount the EDS on the corrosion-free mounting rail that
adheres to the EN 60715 standard.
Suggested Installation Method
STEP 1:
Insert the upper lip of the DIN
-
rail kit into the mounting rail.
S
TEP 2:
Press the device towards the
mounting rail until it snaps into
place.
Alternatively, you can use
a screwdriver to attach to the
bottom of the DIN
-
rail kit and pull
down.
Suggested Removal Method
STEP 1:
Pull down the latch on the DIN
-
rail kit with a screwdriver.
STEP 2:
Slightly pull the device forward
and lift up to remove it from the
mounting rail.
NOTE
1. If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment
may be impaired.
2.
The installation and the safety of any system incorporating
the equipment is the responsibility of the assembler of the
system.
3.
This is an OPEN TYPE module and should be installed in a
safety enclosure with mechanical rigidity and an
appropriate IP rating.

- 9 -
Wall Mounting (optional)
For some applications, you will find it convenient to mount EDS on the
wall, as illustrated below.
There are two options for installation: The first option
is to h
ook the EDS DIN-rail latch on the opening of
the
wall mount kit (see picture above) and then
m
ount the wall-mount kit on the wall with screws.
(The other option is to perform these two steps in
the other order.)
The heads of the screws should be
less than
6.0 mm in diameter, and the shafts should be less than 3.5 mm in
diameter, as shown in the figure at the right.
NOTE
Before tightening screws into the wall, make sure the screw
head and shank size are suitable by inserting th
e screw into
one of the keyhole
-shaped apertures of the Wall Mounting
Plates.
Do not screw the screws in all the way—leave about 2 mm to allow
room for sliding the wall mount panel between the wall and the screws.
Once the screws are fixed in the
wall, insert the
two screw heads
through the large parts of the
keyhole
-shaped apertures, and
then slide EDS downwards, as
indicated. Tighten the
two
screws for added stability.
WARNING
External metal parts are hot. Take necessary precautions if it is
necessary to touch.

- 10 -
Wiring Requirements
WARNING
Do not disconnect modules or wires
unless the power supply
has been switched off or the area is known to be non
-
hazardous.
The devices may only be connected to the supply
voltage shown on the type plate.
The devices are designed for operation with a
Safety Extra-L
ow
V
oltage. Thus, they may only be connected to the supply
voltage connections and to the signal contact with the
Safety
E
xtra-Low Voltages (SELV) in compliance with IEC950/
EN60950/ VDE0805.
WARNING
Safety First!
Be sure to
disconnect the power cord before installing and/or
wiring your
Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire
and common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If t
he current goes above the maximum ratings, the wiring
could overheat, causing serious damage to your equipment.
You should also pay attention to the following items:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power
wiring in the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb
is that wiring that shares similar electrical characteristics can be
bundled together.
•Keep input wiring and output wiring separated.
•It is strongly advised that you label wiring to all devices in the
system when necessary.
Grounding Moxa EtherDevice Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from
the ground screw to the grounding surface prior to connecting devices.
A 4 mm2conductor must be used when a connection to the external
grounding screw is utilized.