Moxa Technologies EDS-600 Series User manual

P/N: 1802006000017
*1802006000017*
EDS-600 Series
Quick Installation Guide
Moxa EtherDevice™ Switch
Version 5.3, March 2021
Technical Support Contact Information
www.moxa.com/support

2021 Moxa Inc. All rights reserved.

- 2 -
Package Checklist
The Moxa EDS-600 Series is shipped with the following items. If any of
these items is missing or damaged, please contact your customer service
representative for assistance.
•1 EDS-600 EtherDevice Switch
•RJ45 to DB9 console port cable
•Protective caps for unused ports (Only for EDS-611 Series and
EDS-619 Series)
•Wall mounting kit (optional—must be ordered separately)
•Anti-vibration wiring kit (optional, must be ordered separately)
•Quick installation guide (printed)
•Warranty card
Features
Advanced Industrial Networking Capabilities
•IPv6 ready (certified by the IPv6 Logo Committee).
•IEEE 1588 PTP V2 (Precision Time Protocol) for precise time
synchronization of networks.
•Supports LLDP (Link Layer Discovery Protocol)
•DHCP Option 82 for IP address assignment with different policies.
•Supports Modbus/TCP industrial Ethernet protocol.
•Turbo Ring and Turbo Chain (< 20 ms recovery time) and STP/RSTP.
•IGMP snooping and GMRP for filtering multicast traffic.
•Port-based VLAN, IEEE 802.1Q VLAN, and GVRP to ease network
planning.
•QoS (IEEE 802.1p/1Q) and TOS/DiffServ to increase determinism.
•Port Trunking for optimal bandwidth utilization.
•IEEE 802.1X, HTTPS, and SSH to enhance network security.
•SNMPv1/v2c/v3 for different levels of network management.
•RMON for efficient network monitoring and proactive capability.
•Bandwidth management prevents unpredictable network status.
•Lock port function for blocking unauthorized access based on MAC
address.
•Port mirroring allows for online debugging.
•Automatic warning by exception through e-mail and relay output.
•Digital inputs to integrate sensors and alarms with IP networks.

- 3 -
Panel Views of the EDS-608
Front Panel:
1. System Status LEDs
2. Fast Ethernet Interface Module port LEDs
3. Fast Ethernet Interface Module
4. Terminal block for 2 power inputs, 1 DI/DO, and 1 relay output
5. Grounding screw
6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring
7. RS-232 Console port
8. Screw to attach Fast Ethernet Interface Module
Rear Panel:
9. DIN-Rail Attachment Plate
10. Screw holes for wall mounting kit

- 4 -
Panel Views of the EDS-611
Front Panel:
1. System Status LEDs
2. Fast Ethernet Interface Module port LEDs
3. Fast Ethernet Interface Module
4. Terminal block for 2 power inputs, 1 DI/DO, and 1 Relay output
5. Grounding screw
6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring
7. RS-232 Console port
8.
G1 to G3: 10/100/1000 BaseT(X) or 100/1000Base SFP slot combo
ports
9. Screw to attach Fast Ethernet Interface Module
10.
Gigabit Ethernet LEDs
Rear Panel:
11.
DIN-Rail Attachment Plate
12. Screw holes for wall mounting kit

- 5 -
Panel Views of the EDS-616
Front Panel:
1. System Status LEDs
2. Fast Ethernet Interface Module port LEDs
3. Fast Ethernet Interface Module
4. Terminal block for 2 power inputs, 1 DI/DO, and 1 relay output
5. Grounding screw
6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring
7. RS-232 Console port
8. Screw to attach Fast Ethernet Interface Module
Rear Panel:
9. DIN-Rail Attachment Plate
10. Screw holes for wall mounting kit

- 6 -
Panel Views of the EDS-619
Front
Panel:
1. System Status LEDs
2. Fast Ethernet Interface Module port LEDs
3. Fast Ethernet Interface Module
4. Terminal block for 2 power inputs, 1 DI/DO, and 1 relay output
5. Grounding screw
6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring
7. RS-232 Console port
8. G1 to G3: 10/1
00/1000 BaseT(X) or 100/1000Base SFP slot combo
ports
9. Screw to attach Fast Ethernet Interface Module
10.
Gigabit Ethernet LEDs
Rear Panel:
11.
DIN-Rail Attachment Plate
12. Screw holes for wall mounting kit

- 7 -
Mounting Dimensions
EDS-608/EDS-611

- 8 -
EDS-616/EDS-619
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the
back panel of the EDS-600 when you take it out of the box. If you need to
reattach the DIN-Rail attachment plate to the EDS-600, be sure the
spring-loaded bracket is situated towards the bottom, as shown in the
following figures.
STEP 1:
If the spring
-loaded bracket is
locked in place, p
ush the recessed
button to release it. Once released,
you should feel some resistance
from the sp
ring as you slide the
bracket up and down a few
millimeters in each direction.

- 9 -
STEP 2:
Insert the top of the DIN
-Rail into
the
top slots on the DIN-Rail
attachment plate.
STEP 3:
The DIN
-Rail attachment unit will
snap into place as shown
in the
following illustration.
To remove the Moxa
EDS-600
switch
from the DIN
-
Rail, use a screwdriver
to push down the spring
-loaded
bracket until it locks in place, as
shown in the following diagram.
Next, rotate the bottom of the switch
upwards and
then remove the
switch from the DIN
-Rail.
Wall Mounting (Optional)
For some applications, you will find it convenient to mount the EDS-600
on the wall, as shown in the following illustrations:
STEP 1: Remove the aluminum DIN-Rail attachment plate from the rear
panel of the EDS-600, and then attach the wall mount plates with M3
screws, as shown in the figure at the right.
EDS-608/EDS-611
EDS-616/EDS-619
STEP 2: Mounting the EDS-600 on the wall requires 4
screws. Use the
EDS-600, with wall mount plates
attached, as a guide to mark the correct locations of the
4 screws. The heads of the screws should be less than
6.0 mm in diameter, and the shafts should be less than
3.5 mm in diameter, as shown in the figure at the right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.

- 10 -
Do not screw the screws in all the way—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.
STEP 3: Once the screws are fixed to the wall, insert the four screw heads
through the wide parts of the keyhole-shaped apertures, and then slide
the EDS-600 downwards, as indicated in the figure at the right. Tighten
the four screws for more stability.
ATEX Information
1. Certificate number: DEMKO 11 ATEX 1007817X
2. Certification string: Ex nA nC IIC T4 Gc
3. Standards covered: EN 60079-0:2012+A11:2013, EN
60079-15:2010
4. Special Conditions of Use:
•Devices are to be installed in an ATEX certified Zone 2 enclosure
rated IP54 in accordance with EN 60529 that is accessible only
with the use of a tool.
•Devices are for use in an area of not more than pollution degree
2 in accordance with EN 60664-1.
•Provisions shall be made, external to the apparatus, to prevent
the rated voltage being exceeded by the transient disturbances
of more than 140%.
•Accessory Modules CM-600-4TX, CM-600-4MSC, CM-600-4SSC,
CM-600-4MST, CM-600-2MSC/2TX, CM-600-2SSC/2TX,
CM-600-3MSC/1TX, CM-600-3SSC/1TX must be used with
Models EDS-608, EDS-608-T, EDS-611, EDS-611-T, EDS-616,
EDS-616-T, EDS-619, and EDS-619-T.
•When customers use their own optical SFP communication
modules, these must be limited to Laser Class 1 only in
accordance with EN 60825-1.