Moxa Technologies EDS-505A Series Manual

MOXA EtherDevice™ Switch
EDS-505A/508A Hardware Installation Guide
Fourth Edition, February 2008
Moxa Inc.
Tel: [phone]
Fax: [phone]
www.moxa.com
Moxa Technical support.
Worldwide: [e-mail]
The Americas: [e-mail]
P/N: 1802005000011

—1 —
Package Checklist
The MOXA EDS-505A/508A is shipped with the following items. If any of
these items is missing or damaged, please contact your customer service
representative for assistance.
y1 MOXA EtherDevice Switch (EDS-505A or EDS-508A)
yHardware Installation Guide
yCD-ROM with User’s Manual and Windows Utility
yWarranty Statement
yRJ45 to DB9 Console port cable
yProtective caps for unused ports
yPanel Mounting Kit (optional—must be ordered separately)
Features
¾Advanced Industrial Networking Capability
yPlug-n-Play, Redundant Ethernet Ring and RSTP/STP (IEEE802.1W/D)
yIGMP Snooping and GMRP for filtering multicast traffic from
Industrial Ethernet
ySupports port-based VLAN, IEEE802.1Q VLAN and GVRP protocol to
ease network planning
ySupports QoS-IEEE802.1p/1Q and TOS/DiffServ to increase
determinism
ySupports 802.3ad, LACP for optimum bandwidth utilization
yPort Trunking for optimum bandwidth utilization
yRMON for efficient network monitoring and proactive capability
ySNMP V1/V2c/V3 for different levels of network management security
ySupports IEEE802.1X and https/SSL to enhance network security
¾Designed for IndustrialApplications
yBandwidth management to prevent unpredictable network operation
yPort mirroring for online debugging
yLock port for authorized MAC address access
yDigital inputs to integrate sensors and alarms with IP networks
yAutomatic warning by exception through email, relay output
yAutomatic recovery of IP addresses from connected devices
yLine-swap fast recovery (patent pending)
yRedundant, dual DC power inputs
y-40 to 75°C operating temperature range (for-T models)
yIP30, rugged high-strength case
yDIN-Rail or panel mounting ability
yLong-haul transmission distance of 40 km or 80 km.

—2 —
Panel Layout of EDS-505A/508A
(Standard)
EDS-505A
Front Panel View EDS-508A Front Panel View
7
6
8
9
11
10
12
13
14
15
15
2
14
15
15
V1, V2 INPUTS: 12-45 VDC
RS-232 CONSOLE
------
ON
OFF
MASTER
COUPLER
TURBO
RING
PWR2
4
3
2
1
PWR2
RELAY2
RELAY1
DI1
DI1
V2-
V2+
I1
V1-
V1+
I2
Top Panel View
1
2
3
4
1
Rear Panel View
2
17
16
16
52
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation orifices
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. Master LED
10. Coupler LED
11. Turbo Ring logo
12. TP port’s 100 Mbps LED
13. TP port’s 10 Mbps LED
14. Model Name
15. 10/100BaseT(X) ports
16. Screw hole for wall mounting kit
17. DIN-Rail kit

—3 —
Panel Layout of EDS-505A/508A
(SC-type)
EDS-505A-MM-SC
Front Panel View EDS-508A-MM-SC Front Panel View
14
15
14
16
15
7
6
8
9
11
10
12
13
2
16
17
17
V1, V2 INPUTS: 12-45 VDC
RS-232 CONSOLE
------
ON
OFF
MASTER
COUPLER
TURBO
RING
PWR2
4
3
2
1
PWR2
RELAY2
RELAY1
DI1
DI1
V2-
V2+
I1
V1-
V1+
I2
Top Panel View
1
2
3
4
1
Rear Panel View
2
19
18
18
52
NOTE: The appearance of
EDS-505A-SS-SC is identical to that
of EDS-505A-MM-SC.
The appearance of EDS-508A-SS-SC
is identical to that of
EDS-508A-MM-SC.
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation orifices
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. Master LED
10. Coupler LED
11. Turbo Ring logo
12. TP port’s 100 Mbps LED
13. TP port’s 10 Mbps LED
14. Model Name
15. 10/100BaseT(X) ports
16. 100BaseFX ports
17. FX port’s 100 Mbps LEDs
18. Screw hole for wall mounting kit
19. DIN-Rail kit

—4 —
Panel Layout of EDS-505A/508A
(ST-type)
EDS-505A-MM-ST
Front Panel View EDS-508A-MM-ST Front Panel View
14
15
14
16
15
7
6
8
9
11
10
12
13
2
16
17
17
V1, V2 INPUTS: 12-45 VDC
RS-232 CONSOLE
------
ON
OFF
MASTER
COUPLER
TURBO
RING
PWR2
4
3
2
1
PWR2
RELAY2
RELAY1
DI1
DI1
V2-
V2+
I1
V1-
V1+
I2
Top Panel View
1
2
3
4
1
Rear Panel View
2
19
18
18
52
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation orifices
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. Master LED
10. Coupler LED
11. Turbo Ring logo
12. TP port’s 100 Mbps LED
13. TP port’s 10 Mbps LED
14. Model Name
15. 10/100BaseT(X) ports
16. 100BaseFX ports
17. FX port’s 100 Mbps LEDs
18. Screw hole for wall mounting kit
19. DIN-Rail kit

—5 —
Mounting Dimensions (unit = mm)
Rear View
Side View
Front View
DlN-Rail Kit
DlN-Rail
105.00
9.00
35.00
135.00
24.324.56 46.77 39.37
135.00
Wall Mounting Kit
10
10
5
7.75 30.50 7.75
3.5
6
6
66.80
57.05
13.9 18.2 13.9
30.00 15.0
51.3 13.9
80.2
DlN-Rail Kit
7.5 55 7.5
27.20
48.30
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the back
panel of the EDS-505A/508A when you take it out of the box. If you need to
reattach the DIN-Rail attachment plate, make sure the stiff metal spring is
situated towards the top, as shown in the following figure.
STEP 1:
Insert the top of the DIN-Rail into the
slot just below the stiff metal spring.
STEP 2:
The DIN-Rail attachment unit will
snap into place as shown.
metal
spring
DIN-Rail
metal
spring
DIN-Rail
To remove EDS-505A/508A from the DIN-Rail, simply reverse Steps 1 and 2.

—6 —
Wall Mounting (optional)
For some applications, you will find it convenient to mount the
EDS-505A/508A on the wall, as shown in the following figures.
STEP 1: Remove the
aluminum DIN-Rail
attachment plate from the
EDS-505A/508A’s rear
panel, and then attach the
wall mount plates with M3
screws, as shown in the
figures at the right.
⇒
STEP 2:
Mounting the EDS-505A/508A on the wall requires 4 screws.
Use the EDS, with wall mount plates attached, as a guide to
mark the correct locations of the 4 screws. The heads of the
screws should be less than 6.0 mm in diameter, and the shafts
should be less than 3.5 mm in diameter, as shown in the
figure at the right.
6.0 mm
3.5 mm
NOTE Before tightening the screws into the wall, make sure the screw head
and shank size are suitable by inserting the screw into one of the
keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in completely—leave about 2 mm to allow room for
sliding the wall mount panel between the wall and the screws.
STEP 3: Once the screws are fixed in
the wall, insert the four screw heads
through the large parts of the
keyhole-shaped apertures, and then
slide the EDS-505A/508A
downwards, as indicated. Tighten the
four screws for added stability.
ATEX Information
1. Certificate number 08 ATEX 0712961X
2. Ambient range (-40°C ≤Tamb ≤75°C)
3. Certification string (Ex nC nL IIC T4)
4. Standards covered ( EN60079-0:2006, EN60079-15:2005)
5. The conditions of safe usage:
yThese products must be mounted in an IP54 enclosure.
yInstall in an area of pollution degree 2 or less.
yUse a conductor wire of size 0.2 mm² or greater.
yPROVISIONS SHALL BE MADE, EITHER IN APPARATUS OR
EXTERNAL TO THE APPARATUS, TO PREVENT THE RATED
VOLTAGE BEING EXCEEDED BY THE TRANSIENTS
DISTURBANCES OF MORE THAN 40 %

—7 —
Wiring Requirements
WARNING
The power for this product is intended to be supplied by a Listed
Power Unit, with output marked LPS, and rated to deliver 12 to
45 VDC at a maximum of 600 mA.
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your MOXA EtherDevice Switch. Calculate the maximum
possible current in each power wire and common wire. Observe
all electrical codes dictating the maximum current allowable for
each wire size. If the current goes above the maximum ratings,
the wiring could overheat, causing serious damage to your
equipment.
Please read and follow these important guidelines:
yUse separate paths to route wiring for power and devices. If power wiring
and device wiring paths must cross, make sure the wires are perpendicular
at the intersection point.
yNOTE: Do not run signal or communications wiring, and power wiring
through the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.
yUse the type of signal transmitted through a wire to determine which wires
should be kept separate. The rule of thumb is that wiring that shares similar
electrical characteristics can be bundled together.
yKeep input wiring and output wiring separate.
yIt is strongly advised that you label wiring to all devices in the system,
when necessary.
Grounding the EtherDevice Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface, such as a metal panel.
Wiring the Relay Contact
The EDS-505A/508A has two sets of relay output—relay 1 and relay 2. Each
relay contact consists of two contacts of the terminal block on the
EDS-505A/508A’s top panel. Refer to the next section for detailed instructions
on how to connect the wires to the terminal block connector, and how to attach
the terminal block connector to the terminal block receptor. The meaning of the
two contacts used to connect the relay contacts is illustrated below.

—8 —
Relay1 Relay2
Relay1 Relay2
The fault circuit will open if::
1. A relay warning event is
triggered, OR
2. The EDS-505A/508A is the
Master of this Turbo Ring,
and the Turbo Ring is broken,
OR
3. Start-up failure.
If none of these three conditions
is met, the fault circuit will
remain closed.
Wiring the Redundant Power Inputs
The EDS-505A/508A unit has two sets of power inputs—power input 1 and
power input 2.The top two contacts and the bottom two contacts of the 6-pin
terminal block connector on the top panel are used for the EDS’s two digital
inputs. Top and front views of one of the terminal block connectors are shown
below.
PWR1 PWR2
V1- V1+
PWR1
V2- V2+
PWR2
V1- V1+ V2- V2+
Take the following steps to wire
the redundant power inputs:
STEP 1: Insert the
negative/positive DC wires into
the V-/V+ terminals.
STEP 2: To keep the DC wires
from pulling loose, use a small
flat-blade screwdriver to tighten
the wire-clamp screws on the
front of the terminal block
connector.
STEP 3: Insert the plastic
terminal block connector prongs
into the terminal block receptor,
which is located on the EDS’s top
panel.
ATTENTION
Before connecting the EDS to the DC power inputs, make sure
the DC power source voltage is stable.
Wiring the Digital Inputs
The EDS-505A/508A unit has two sets of digital inputs, DI 1 and DI 2. Each
DI consists of two contacts of the 6-pin terminal block connector on the EDS’s
top panel. The remaining contacts are used for the EDS’s two DC inputs. Top
and front views of one of the terminal block connectors are shown below.

—9 —
I1
D2I
I2
D1I
I1I2
D2ID1I
Take the following steps to wire
the digital inputs:
STEP 1: Insert the negative
(ground)/positive DI wires into
the ┴/I1 terminals.
STEP 2: To keep the DI wires
from pulling loose, use a small
flat-blade screwdriver to tighten
the wire-clamp screws on the
front of the terminal block
connector.
STEP 3: Insert the plastic
terminal block connector prongs
into the terminal block receptor,
which is located on the
EDS-505A/508A’s top panel.
Communication Connections
EDS-508A models have 8 or 6 10/100BaseT(X) Ethernet ports, and 0 (zero) or
2 100BaseFX (SC/ST-type connector) fiber ports. EDS-505A models have 5 or
3 10/100BaseT(X) Ethernet ports, and 0 (zero) or 2 100 BaseFX (SC/ST-type
connector) fiber ports
10/100BaseT(X) Ethernet Port Connection
The 10/100BaseT(X) ports located on EDS’s front panel are used to connect to
Ethernet-enabled devices.
Next, we show pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports, and also show cable wiring diagrams for
straight-through and cross-over Ethernet cables.
MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45
Pin Signal Pin Signal
1 Tx+ 1 Rx+
2 Tx- 2 Rx-
3 Rx+ 3 Tx+
6 Rx- 6 Tx-
RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring
Straight-Through Cable
RJ45 Plug Pin 1
Switch Port
RJ45
Connector RJ45 Connecto
r
Tx+
Tx-
Rx+
Rx-
NIC Port
Cable Wiring
3 3
6 6
1 1
2 2
Rx+
Rx-
Tx+
Tx-
1 8