Moxa Technologies EDS-316 Series User manual

P/N: 1802003160015
*1802003160015*
EDS-316 Series
Quick Installation Guide
Moxa EtherDevice Switch
Version 6.2, January 2021
Technical Support Contact Information
www.moxa.com/support

2021 Moxa Inc. All rights reserved.

- 2 -
Overview
The Moxa EtherDevice™ EDS-316 series of 16-port smart Ethernet
switches provides an economical solution for your Ethernet connections.
As an added bonus, the built-in smart alarm function helps system
maintainers monitor the health of your Ethernet network.
EDS-316 has a wide operating temperature range of -40 to 75°C, and is
designed to withstand a high degree of vibration and shock. The rugged
hardware design makes EDS-316 series perfect for ensuring that your
Ethernet equipment can withstand critical industrial applications, such as
in hazardous locations (Class 1 Division 2/ Zone 2), and complies with
FCC, TÜV, UL, and CE Standards.
NOTE
Throughout this Hardware Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch:
EDS = Moxa EtherDevice Switch
Package Checklist
Moxa EDS-316 is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service
representative for assistance.
•Moxa EtherDevice™ Switch
•Protective caps for unused ports
•Quick installation guide (printed)
•Warranty card
Features
High Performance Network Switching Technology
•10/100BaseT(X) (RJ45), 100BaseFX (SC/ST type, Multi/Single mode)
•IEEE 802.3/802.3u/802.3x
•Store and Forward switching process type, with 4K address entries
•10/100M, Full/Half-Duplex, MDI/MDIX auto-sensing
Industrial Grade Reliablity
•Power failure, port break alarm by relay output
•Redundant dual DC power inputs
•Broadcast storm protection to prevent network devices from crashing
Rugged Design
•Operating temperature range of 0 to 60°C, or extended operating
temperature of -40 to 75°C for (-T) models
•IP30, rugged high-strength case
•DIN-Rail or wall mounting ability

- 3 -
Panel Layout of EDS-316 (standard-type)
1. Grounding screw
2. Terminal block for power input
(PWR1, PWR2) and relay output
3. Heat dissipation orifices
4. DIP switches
(EDS-316 has 18 DIP switches
in
total; 1 DIP switch is reserved)
5. Power input PWR1 LED
6. Power input PWR2 LED
7. Fault LED
8. 10/100BaseT(X) Port
9. TP port’s 100 Mbps LED
10.
TP port’s 10 Mbps LED
11.
Model Name
12.
Screw hole for wall mounting kit
13.
DIN-Rail Kit

- 4 -
Panel Layout of EDS-316 (SC-type)
Product models not shown here:
EDS
-316-S-SC is identical to
EDS
-316-M-SC.
EDS
-316-SS-SC and EDS-316-MS-
SC
are identical to
EDS-316-MM-SC.
1. Grounding screw
2. Terminal block for power input
(PWR1, PWR2) and relay output
3. Heat dissipation orifices
4. DIP switches (EDS-316 series has
18 DIP switches in total; 1 DIP
switch is reserved)
5. Power input PWR1 LED
6. Power input PWR2 LED
7. Fault LED
8. 10/100BaseT(X) Port
9. TP port’s 100 Mbps LED
10.
TP port’s 10 Mbps LED
11.
Model Name
12.
100BaseFX Port
SSC for EDS-316-MS-SC
SSC-80 for EDS-316-SS-SC-40/80
13.
100BaseFX Port
MSC for EDS-316-MS-SC
SSC-40 for EDS-316-SS-SC-40/80
14.
FX port’s 100 Mbps LED
15.
Screw hole for wall mounting kit
16.
DIN-Rail Kit
NOTE
MSC = Multi-Mode SC Connector
SSC
= Single-Mode SC Connector
SSC-80 = Single-Mode SC Connector (80 km)

- 5 -
Panel Layout of EDS-316 (ST-type)
1. Grounding screw
2. Terminal block for power input
(PWR1, PWR2) and relay output
3. Heat dissipation orifices
4. DIP switches
(EDS-316 has 18 DIP switches in
total; 1 DIP switch is reserved)
5. Power input PWR1 LED
6. Power input PWR2 LED
7. Fault LED
8. 10/100BaseT(X) Port
9. TP port’s 100 Mbps LED
10.
TP port’s 10 Mbps LED
11.
Model Name
12.
100BaseFX Port
13.
FX port’s 100 Mbps LED
14.
Screw hole for wall mounting kit
15.
DIN-Rail Kit

- 6 -
Mounting Dimensions
Unit = mm (inch)
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the
back panel of EDS-316 when you take it out of the box. If you need to
reattach the DIN-Rail attachment plate, make sure the stiff metal spring
is situated towards the top, as shown in the figures below.
STEP 1:
Insert the top of the DIN
-Rail into
the slot just
below the stiff metal
spring.
STEP 2:
The DIN
-Rail attachment unit will
snap into place as shown below.
To remove Moxa EtherDevice Switch from the DIN-Rail, simply reverse
Steps 1 and 2 above.

- 7 -
Wall Mounting (optional)
For some applications, you will find it convenient to mount EDS-316 on
the wall, as illustrated in the figure.
STEP 1: Remove the
aluminum DIN
-Rail
attachment plate from
EDS
-316’s rear panel, and
then attach the wall mount
plates, as shown in the
figu
re.
STEP 2:
Mounting EDS-316 on the wall requires 4
screws. Use the
switch, with wall mount plates
attached, as a guide to mark the correct locations of the
4 screws. The heads of the screws should
be less than
6.0 mm in diameter, and the shafts should be less than
3.5 mm in diameter, as shown in the figure at the right.
NOTE
Before tightening screws into the wall, make sure the screw head
and shank size are suitable by inserting the screw into one of the
keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.
STEP 3: Once the screws are fixed
in the wall, insert
the four screw
heads through the large parts of
the keyhole
-shaped apertures,
and then slide EDS
-316
downwards, as indicated. Tighten
the four screws for
added
stability.
ATTENTION
The equipment shall be installed in a
n enclosure that is only
accessible using the correct tool with at least
an IP54 rating in
accordance with IEC/EN 60079
-15. It should not be used in an
area with pollution degree 2 or higher as defined in IEC 60664-1.
These devices are open-type devices that are to be installed in an
enclosure only accessible with the use of a correct tool. This equipment is
only suitable for use in Class I, Division 2, Groups A, B, C and D or
non-hazardous locations.

- 8 -
WARNING
EXPLOSION HAZ
ARD – Servicing, replacing, and installing the
product can only take place is an area that is non-hazardous.
ATEX Information
1. Certificate number DEMKO 09 ATEX 0812123X
2. Ambient range: 0°C to 60°C (For suffix without–T), -40°C to 75°C
(For suffix with–T)
3. Certification string: Ex nA nC IIC T4 Gc
4. Rated Cable Temperature: ≧100°C
5. Standards covered:
EN 60079-0:2012+A11:2013, EN 60079-15:2010
6. The conditions of safe usage:
•These products must be mounted in an IP54 enclosure.
•Install in an area of pollution degree 2 or less.
•Use a conductor wire of size 0.2 mm² or greater.
•Conductors suitable for use in an ambient temperature of 93°C
must be used for the Power Supply Terminal.
•PROVISIONS SHALL BE MADE, EITHER IN EXTERNAL TO THE
APPARATUS, TO PREVENT THE RATED VOLTAGE BEING
EXCEEDED BY THE TRANSIENTS DISTURBANCES OF MORE
THAN 40 %
Wiring Requirements
WARNING
EXPLOSION HAZARD
- Substitution of any components may
impair suitability for Class I, Division 2.
WARNING
Do not disconnect modules or wires unless the power supply has
been switched off or the area is known to be non
-hazardous.
The
devices may only be connected to the supply voltage shown on
the type plate.
The devices a
re designed for operation with a Safety Extra-L
ow
Voltage. Thus, they may only be connected to the supply voltage
connections and to the signal contact with the
Safety Extra-L
ow
Voltages (SELV) in compliance with IEC950/ EN60950/ VDE0805.

- 9 -
WARNING
Substitution of components may impair suitability for Class
I,
Division 2
, and Zone 2. These devices must be supplied by an
SELV source as defined in Low Voltage Directive 73/23/EEC and
93/68/EEC.
WARNING
This unit is a built
-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your
Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes
dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
You should also pay attention to the following items:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
in the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
•Keep input wiring and output wiring separated.
•It is strongly advised that you label wiring to all devices in the system
when necessary.
•Only use copper conductors with 60/75°C capability
Grounding Moxa EtherDevice Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices. A
4mm 2 conductor must be used when a connection to the external
grounding screw is utilized.

- 10 -
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface, such as a metal panel.
Wiring the Alarm Contact
The Alarm Contact consists of the two middle contacts of the terminal
block on EDS’s top panel. You may refer to the next section for detailed
instructions on how to connect the wires to the terminal block connector,
and how to attach the terminal block connector to the terminal block
receptor.
In this section, we explain the meaning of the two contacts used to
connect the Alarm Contact.
FAULT: The two middle contacts of the 6-contact
terminal block connector
are used to detect both
power faults and port faults. The two wires attached
to the Fault contacts
form an open circuit when:
1. EDS has lost power from one of the DC power
inputs.
OR
2.
The PORT ALARM DIP Switch for one of the ports
is set to ON, but the port is not connected
properly.
If
neither of these two conditions is satisfied, the
Fault circuit will be closed.
Wiring the Redundant Power Inputs
The top two contacts and the bottom two contacts of the 6-contact
terminal block connector on EDS’s top panel are used for EDS’s two DC
inputs. Top and front views of one of the terminal block connectors are
shown here.
STEP 1:
Insert the negative/positive DC wires into
the
V-/V+ terminals.
STEP 2:
To keep the DC wires from pulling
loose, use
a small flat
-blade screwdriver to tighten the
wire
-
clamp screws on the front of the terminal block
connector.
STEP 3:
Insert the plastic terminal block connector
prongs into the terminal block receptor, which is
located on
EDS’s top panel.
ATTENTION
Before connecting EDS to the DC power inputs, make sure the DC
power source voltage is stable.