Moxa Technologies EtherDevice EDS-510A Series Manual

Moxa EtherDevice™ Switch
EDS-510A Series Hardware Installation Guide
Sixth Edition, May 2010
©2010 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan,
R.O.C.
TEL: [phone]
P/N: 1802005100013

- 2 -
Package Checklist
The EDS-510A is shipped with the following items. If any of these items are
missing or damaged, please contact your customer service representative for
assistance.
y1 EDS-510A EtherDevice Switch
yHardware Installation Guide (this guide)
yCD-ROM with user’s manual and Windows utility
yMoxa product warranty statement
yRJ45 to DB9 console port cable
yProtective caps for unused ports
yDIN-Rail mounting kit (attached to the EDS-510A’s rear panel by default)
Optional Accessories
ySFP-1GSXLC: Small Form factor Pluggable transceiver with 1000BaseSX,
LC, 0.5km, 0 to 60°C
ySFP-1GSXLC-T: Small Form factor Pluggable transceiver with
1000BaseSX, LC, 0.5km, 20 to 75°C
ySFP-1GLXLC: Small Form factor Pluggable transceiver with 1000BaseLX,
LC, 10km, 0 to 60°C
ySFP-1GLXLC-T: Small Form factor Pluggable transceiver with
1000BaseLX, LC, 10km, -40 to 75°C
ySFP-1GLHXLC: Small Form factor Pluggable transceiver with
1000BaseLHX, LC, 40 km, 0 to 60°C
ySFP-1GLHXLC-T: Small Form factor Pluggable transceiver with
1000BaseLHX, LC, 40 km, -40 to 75°C
ySFP-1GZXLC: Small Form factor Pluggable transceiver with 1000BaseZX,
80 km, LC, 0 to 60°C
yABC-01: Automatic Backup Configurator via RS-232 Console Port, 0 to
60°C
yDR-4524—DIN-Rail Power Supply (24 VDC, 45W/2A, with 85 to 264
VAC input)
yDR-75-24—DIN-Rail Power Supply (24 VDC, 75W/3.2A, with 85 to 264
VAC input)
yDR-120-24—DIN-Rail Power Supply (24 VDC, 120W/5A, with 88 to 132
VAC/176 to 264 VAC input by switch)
yEDS-SNMP OPC Server Pro—CD with EDS-SNMP OPC Server
software and user’s manual
yWK-46—Wall Mounting Kit (will be shipped with the product)
yRK-4U—4U-high 19" rack mounting kit

- 3 -
Panel Views of EDS-510A
EDS-510A-1GT2SFP
Front Panel View
EDS-510A-3GT
Front Panel View
EDS-510A-3SFP
Front Panel View
7
6
8
9
1
14
1
11
13
12
2
3
4
5
10
7
6
8
9
1
14
1
11
13
12
2
3
4
5
10
7
6
8
9
1
14
1
11
13
12
2
3
4
5
10
MSTR/HEAD
CPLR/TAILD
MSTR/HEAD
CPLR/TAILD
MSTR/HEAD
CPLR/TAILD
1. 1 to 7: 10/100BaseT(X) port
2. G1:
EDS-510A-3GT
10/100/1000BaseT(X) port
EDS-510A-1GT2SFP
10/100/1000BaseT(X) port
EDS-510A-3SFP
1000BaseSX/LX/LHX/ZX port
3. G2:
EDS-510A-3GT
10/100/1000BaseT(X) port
EDS-510A-1GT2SFP
1000BaseSX/LX/LHX/ZX port
EDS-510A-3SFP
1000BaseSX/LX/LHX/ZX port
4. G3:
EDS-510A-3GT
10/100/1000BaseT(X) port
EDS-510A-1GT2SFP
1000BaseSX/LX/LHX/ZX port
EDS-510A-3SFP
1000BaseSX/LX/LHX/ZX port
5. G1, G2, G3: LED indicators for
1000 Mbps ports
6. PWR1: LED for power input 1
7. PWR2: LED for power input 2
8. FAULT: LED indicator
9. MSTR/HEAD: LED indicator
10. CPLR/TAIL: LED indicator
11. Turbo Chain logo
12. 100M: LED indicator for TP port
13. 10M: LED indicator for TP port
14. Model Name

- 4 -
RS-232 CONSOLE
------
ON
OFF
MASTER
COUPLER
TURBO
RING
4
32
1
PWR2
RELAY2
RELAY1
DI2
DI1
V2-
V2+
I1
V1-
V1+
I2
Top Panel View
1
5
6
3
2
1
Rear Panel View
2
8
7
7
4PWR1
Top Panel:
1. Ground screw
2. RS-232 console port
3. Heat dissipation orifices
4. DIP switches for Ring Master,
Ring Coupler, and Turbo Ring
5. 6-pin terminal block for DI 1, DI 2,
and PWR 2
6. 6-pin terminal block for PWR1,
Relay 1, and Relay 2
Rear Panel:
7. Screw holes for Wall Mounting Kit
8. DIN-Rail Kit
Mounting Dimensions (unit = mm)
Rear View
Side View Front View
DlN-Rail Kit
DlN-Rail
105.00
9.00
00.53
00.531
3.42
73.9377.6465.42
00.531
Wall Mounting Kit
10
10
5
7.75 30.50 7.75
3.5
6
6
08.66 50.75
13.9 18.2 13.9
30.00 15.0
51.3 13.9
80.2
DlN-Rail Kit
7.5 55 7.5
02.72 03.84

- 5 -
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the back
panel of the EDS-510A when you take it out of the box. If you need to
reattach the DIN-Rail attachment plate to the EDS-510A, make sure the stiff
metal spring is situated towards the top, as shown by the following figures.
STEP 1—Insert the top of the
DIN-Rail into the slot just below the
stiff metal spring.
STEP 2—The DIN-Rail attachment
unit will snap into place as shown in
the following illustration.
metal
spring
DIN-Rail
metal
spring
DIN-Rail
To remove the EDS-510A from the DIN-Rail, simply reverse Steps 1 and 2
above.
Wall Mounting (Optional)
For some applications, you will find it convenient to mount Moxa EDS-510A
on the wall, as shown in the following illustrations:
STEP 1—Remove the
aluminum DIN-Rail
attachment plate from the rear
panel of the EDS-510A, and
then attach the wall mount
plates with M3 screws, as
shown in the figure at the
right.
Ö
STEP 2—Mounting the EDS-510A on the wall requires 4
screws. Use the EDS-510A, with wall mount plates attached, as a
guide to mark the correct locations of the 4 screws. The heads of
the screws should be less than 6.0 mm in diameter, and the shafts
should be less than 3.5 mm in diameter, as shown in the figure on
at right.
6.0 mm
3.5 mm
NOTE Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.

- 6 -
Do not screw the screws in all the
way—leave about 2 mm to allow room
for sliding the wall mount panel between
the wall and the screws.
STEP 3—Once the screws are fixed to
the wall, insert the four screw heads
through the wide parts of the
keyhole-shaped apertures, and then slide
the EDS-510A downwards, as indicated
in the figure at the right. Tighten the four
screws for more stability.
II 3G
ATEX Information
1. Certificate number DEMKO 08 ATEX 0810937x
2. Ambient range (-40°C ≤Tamb ≤75°C)
3. Certification string (Ex nC nL IIC T4)
4. Standards covered ( EN60079-0:2006,
EN60079-15:2005)
5. The conditions of safe usage:
yThese products must be mounted in an IP54 enclosure.
yInstall in an area of pollution degree 2 or less.
yUse a conductor wire of size 0.2 mm² or greater.
yPROVISIONS SHALL BE MADE, EITHER IN EXTERNAL TO
THE APPARATUS, TO PREVENT THE RATED VOLTAGE BEING
EXCEEDED BY THE TRANSIENTS DISTURBANCES OF MORE
THAN 40 %
Wiring Requirements
WARNING
Do not disconnect modules or wires unless power has been
switched off or the area is known to be non-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
Safety Extra-Low Voltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
Safety Extra-Low Voltages (SELV) in compliance with IEC950/
EN60950/ VDE0805.
ATTENTION
This unit is a built-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).

- 7 -
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Please read and follow these guidelines:
yUse separate paths to route wiring for power and devices. If power wiring
and device wiring paths must cross, make sure the wires are perpendicular
at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately
yYou can use the type of signal transmitted through a wire to determine
which wires should be kept separate. The rule of thumb is that wiring that
shares similar electrical characteristics can be bundled together
yYou should separate input wiring from output wiring
yWe advise that you label the wiring to all devices in the system.
Grounding the Moxa EDS-510A
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface such as a metal panel.
Wiring the Relay Contact
The EDS-510A has two sets of relay outputs—relay 1 and relay 2. Each relay
contact uses two contacts of the terminal block on the EDS-510A’s top panel.
Refer to the next section for detailed instructions on how to connect the wires
to the terminal block connector, and how to attach the terminal block
connector to the terminal block receptor.In this section, we illustrate the
meaning of the two contacts used to connect the relay contact.
RELAY1
RELAY1
RELAY2
RELAY2
FAULT:
The two sets of relay contacts of the
6-pin terminal block connector are
used to detect user-configured events.
The two wires attached to the fault
contacts form an open circuit when a
user-configured event is triggered. If a
user-configured event does not occur,
the fault circuit remains closed.

- 8 -
Wiring the Redundant Power Inputs
The EDS-510A has two sets of power inputs—power input 1 and power input
2. The top two contacts and the bottom two contacts of the 6-pin terminal
block connector on the EDS-510A’s top panel are used for the two digital
inputs. The top and front views of one of the terminal block connectors are
shown here.
PWR1
PWR2
V1- V1+
PWR1
V2- V2+
PWR2
V1- V1+V2- V2+
STEP 1: Insert the negative/positive
DC wires into the V-/V+ terminals,
respectively.
STEP 2: To keep the DC wires from
pulling loose, use a small flat-blade
screwdriver to tighten the wire-clamp
screws on the front of the terminal
block connector.
STEP 3: Insert the plastic terminal
block connector prongs into the
terminal block receptor, which is
located on the EDS-510A’s top panel.
Wiring the Digital Inputs
The EDS-510A has two sets of digital inputs, DI 1 and DI 2. Each DI consists
of two contacts of the 6-pin terminal block connector on the EDS-510A’s top
panel, which are used for the two DC inputs. The top and front views of one
of the terminal block connectors are shown here.
I1
D2I
I2
D1I
I1I2
D2ID1I
STEP 1: Insert the negative
(ground)/positive DI wires into the ┴/I1
terminals, respectively.
STEP 2: To keep the DI wires from
pulling loose, use a small flat-blade
screwdriver to tighten the wire-clamp
screws on the front of the terminal block
connector.
STEP 3: Insert the plastic terminal block
connector prongs into the terminal block
receptor, which is located on the
EDS-510A’s top panel.
Communication Connections
Each EDS-510A switch has 3 types of communication port:
y1 RJ45 console port (RS-232 interface)
y7 10/100BaseTX Ethernet ports
y3 gigabit Ethernet ports:
3 10/100/1000BaseTX ports, or 1 10/100/1000BaseTX and 2
1000BaseSFP (mini-GBIC) ports, or 3 1000BaseSFP (mini-GBIC) ports

- 9 -
In this section, we present two types of diagrams—Pinout Diagrams and Cable
Wiring Diagrams—that convey information about the ports and the cables used
to connect the EDS-510A to other devices:
Pinouts—The “Pinouts” diagrams display the type of signal passing through
each of the port’s pins.
Cable Wiring—The “Cable Wiring” diagrams present standard cable wiring
schemes for cables used to connect the EDS-510A’s ports to other devices.
These diagrams display three pieces of information:
1. When building your own cable, refer to the “pin-to-pin” cable wiring
information displayed between the two vertical dashed lines to see
which pin of the connector on the left should be connected to which pin
of the connector on the right.
2. The information to the left of the left vertical dashed lines gives the
pinouts of the relevant EDS-510A port.
3. The information to the right of the right vertical dashed line gives the
pinouts of the opposing device’s port.
NOTE 1. The pin numbers for male DB9 connectors and hole numbers
for female DB9 connectors are labeled on the connector.
2. The pin numbers for 10-pin RJ45 connectors (and ports) are
typically not labeled on the connector (or port). Refer to the
following Pinout and Cable Wiring diagrams to see how
10-pin RJ45 pins are numbered
RS-232 Connection
The EDS-510A has one RS-232 (10-pin RJ45) console port, located on the
top panel. Use either an RJ45-to-DB9 (see the cable following wiring
diagrams) to connect the EDS-510A’s console port to your PC’s COM port.
You may then use a console terminal program, such as Moxa PComm
Terminal Emulator, to access the EDS-510A’s console configuration utility.
RJ45 (10-pin) Console Port Pinouts
Pin Description
1 ------
2 DSR
3 ------
4 GND
5 TxD
6 RxD
7 GND
8 ------
9 DTR
10 ------
110

- 10 -
RJ45 (10-pin) to DB9 (F) Cable Wiring
RJ45 Plug Pin 1
Moxa
EtherDevice
Server
RJ45
Connector
DCD
DSR
RTS
GND
TxD
RxD
CTS
DTR
COM Port
Female DB9
Connector
DCD
DTR
CTS
GND
RxD
TxD
RTS
DSR
Cable Wiring
1
2
3
4/7
5
6
8
9
1
6
7
5
3
2
8
4
10/100BaseT(X) Ethernet Port Connection
The 10/100BaseT(X) ports located on the EDS-510A’s front panel are used to
connect to Ethernet-enabled devices. Most users configure these ports for
Auto MDI/MDI-X mode, in which case the port’s pinouts are adjusted
automatically depending on the type of Ethernet cable used (straight-through
or cross-over), and the type of device (NIC-type or HUB/Switch-type)
connected to the port.
In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports. We also give cable wiring diagrams for
straight-through and cross-over Ethernet cables.
RJ45 (8-pin, MDI) Port Pinouts
Pin Signal
1 Tx+
2 Tx-
3 Rx+
6 Rx-
1 8
RJ45 (8-pin, MDI-X) Port Pinouts
Pin Signal
1 Rx+
2 Rx-
3 Tx+
6 Tx-
1 8
RJ45 (8-pin) to RJ45 (8-pin) Straight-through Cable Wiring
Straight-Through Cable
RJ45 Plug Pin 1
Switch Port
RJ45
Connector RJ45 Connecto
r
Tx+
Tx-
Rx+
Rx-
NIC Port
Cable Wiring
3 3
6 6
1 1
2 2
Rx+
Rx-
Tx+
Tx-
RJ45 (8-pin) to RJ45 (8-pin) Cross-over Cable Wiring
Cross-Over Cable
RJ45 Plug Pin 1
Switch Port
(NIC Port)
RJ45
Connector RJ45 Connector
Tx+
Tx-
Rx+
Rx-
(Rx+)
(Rx-)
(Tx+)
(Tx-)
(Tx+)
(Tx-)
(Rx+)
(Rx-)
Switch Port
(NIC Port)
Cable Wiring
3 1
6 2
1 3
2 6
Rx+
Rx-
Tx+
Tx-