Moxa Technologies EDS-510E Series Manual

2013 Moxa Inc. All rights reserved.
P/N: 1802005100040
EDS-510E Series
Hardware Installation Guide
Moxa EtherDevice™ Switch
First Edition, July 2013

- 2 -
Package Checklist
The EDS-510E is shipped with the following items. If any of these items
are missing or damaged, please contact your customer service
representative for assistance.
•1 EDS-510E Ethernet switch
•Hardware installation guide
•Documentation and software CD
•Moxa product warranty statement
•USB cable
•Protective caps for unused ports
Features
•2 Gigabit Ethernet ports for redundant ring and 1 Gigabit Ethernet
port for uplink solution
•Turbo Ring and Turbo Chain (recovery time < 20 ms @ 250 switches),
RSTP/STP, and MSTP for network redundancy
•RADIUS, TACACS+, SNMPv3, IEEE 802.1x, HTTPS, and SSH to
enhance network security
•EtherNet/IP, PROFINET, and Modbus/TCP protocols supported for
device management and monitoring

- 3 -
Panel Views of EDS-510E
Front Panel
Top Panel
Rear Panel
Front Panel
1.
1 to 7 port status LED
2.
1 to 7: 10/100BaseT(X) port
3.
System status LED:
•STATE LED indicator
•PWR1 LED indicator
•PWR2 LED indicator
•FAULT LED indicator
•MSTR/HEAD LED indicator
•CPLR/TAIL LED indicator
4.
USB storage port
5.
G1 to G3 port status LED
6.
G1 to G3:
10/100/1000BaseT(X) or
100/1000BaseSFP combo port
7.
Model Name
Top Panel
1.
Reset button
2.
USB console port
3.
DIP switches for Turbo Ring,
Ring Master, and Ring Coupler
4.
Grounding screw
5.
4-pin terminal block for digital
input and power input 2
6.
4-pin terminal block for relay
output and power input 1
Rear Panel
1.
Screw holes for wall mounting
kit
2.
DIN-Rail mounting kit

- 4 -
Mounting Dimensions
Unit = mm (inch)

- 5 -
DIN-Rail Mounting
The metal DIN-rail kit is fixed to the back panel of the EDS-510E when
you take it out of the box. Mount the EDS-510E on corrosion-free
mounting rails that meet the EN 60715 standard.
Installation
STEP 1—Insert the upper lip of the DIN rail into the DIN-rail mounting kit.
STEP 2—Press the EDS-510E t towards the DIN rail until it snaps into
place.
Removal
STEP 1—Pull down the latch on the mounting kit with a screwdriver.
STEP 2 & 3—Slightly pull the EDS-510E forward and lift up to remove it
from the DIN rail.

- 6 -
Wall Mounting (Optional)
For some applications, you will find it convenient to mount Moxa
EDS-510E on the wall, as shown in the following illustrations:
STEP 1—Remove the
aluminum DIN rail attachment
plate from the rear panel
of
the EDS
-510E, and then
attach the wall mount plates
with M3 screws
, as shown in
the figure
at the right.
STEP 2—
Mounting the EDS-510E
on the wall requires
4 screws. Use the
EDS-510E, with wall mount plates
attached, as a guide to mark the correct locations of
the 4 screws. The heads of the screws should be less
than 6.0 mm in diameter, and the shafts should be less
than 3.5
mm in diameter, as shown in the figure on a
t
right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.
STEP 3—
Once the screws are fixed
to
the wall, insert the four screw
heads through the wide parts of the
keyhole
-
shaped apertures, and then
slide
the EDS-510E downwards, as
ind
icated in the figure at the right.
Tighten the four screws for
more
stability
.
Wiring Requirements
WARNING
Do not disconnect modules or wires unless power has been
switched off or the area is known to be non
-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
S
afety Extra-Low V
oltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
S
afety Extra-Low Voltages (SELV) in compliance with IEC950/
EN60950/ VDE0805.

- 7 -
ATTENTION
This unit is a built
-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply
with fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Please read and follow these guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together
•You should separate input wiring from output wiring
•We advise that you label the wiring to all devices in the system.
Grounding the Moxa EDS-510E
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface such as a metal panel.
Wiring the Relay Contact
The EDS-510E has one set of relay output. This relay contact uses two
contacts of the terminal block on the EDS-510E’s top panel. Refer to the
next section for detailed instructions on how to connect the wires to the
terminal block connector, and how to attach the terminal block connector
to the terminal block receptor. In this section, we illustrate the use of two
contacts used to connect the relay.

- 8 -
FAULT:
The two contacts of the 6
-pin terminal
block connector are used to detect
user
-configured events. The two wires
attached to the
fault contacts form an
open circuit when a user
-configured
event is triggered. If a user
-configured
event does not occur, the
fault circuit
remains closed.
Wiring the Redundant Power Inputs
The EDS-510E has two sets of power inputs—power input 1 and power
input 2. The top and front views of one of the terminal block connectors
are shown here.
STEP 1: Insert the negative/positive DC
wires into the V
-/V+ terminals,
respectively.
STEP 2:
To keep the DC wires from
pulling loose, use a small flat
-blade
screwdriver to tighten
the wire-clamp
screws on the front of the terminal block
connector.
STEP 3:
Insert the plastic terminal block
connector prongs into the terminal block
receptor, which is located on
the
EDS-510E’s top panel.
Wiring the Digital Inputs
The EDS-510E has one set of digital input (DI). The DI consists of two
contacts of the 4-pin terminal block connector on the EDS-510E's top
panel, which are used for the two DC inputs. The top and front views of
one of the terminal block connectors are shown here.
STEP 1: Insert the negative
(ground)/positive DI wires into the
┴
/I
terminals
, respectively.
STEP 2:
To keep the DI wires from
pulling loose, use a small flat
-blade
screwdriver to tighten the wire
-clamp
screws on the front of the terminal block
connector.
STEP 3:
Insert the plastic terminal block
connector prongs into the terminal block
receptor, which is located on
the
EDS-510E’s top panel.
Communication Connections
Each EDS-510E switch has 4 types of communication ports:
•1 USB console port (type B connector)
•1 USB storage port (type A connector)
•7 10/100BaseTX Ethernet ports
•3 Gigabit Ethernet ports:
3 10/100/1000BaseTX and 3 100/1000BaseSFP ports

- 9 -
USB Console Connection
The EDS-510E has one USB console port (type B connector), located on
the top panel. Use the USB cable (provided in the product package) to
connect the EDS-510E's console port to your PC's USB port and install the
USB driver (available in the software CD) on the PC. You may then use a
console terminal program, such as Moxa PComm Terminal Emulator, to
access the EDS-510E’s console configuration utility.
USB Console Port (Type B Connector) Pinouts
Pin
Description
1
D– (Data -)
2
VCC (+5V)
3
D+ (Data+)
4
GND (Ground)
USB Storage Connection
The EDS-510E has one USB storage port (type A connector) on the front
panel. Use Moxa ABC-02-USB-T automatic backup configurator to
connect the EDS-510E's USB storage port for configuration backup,
firmware upgrade or system log file backup.
ABC-02-USB Installation
Plug the ABC-02-USB into the USB storage port of the Moxa EDS-510E.
Securing the ABC-02-USB on the wall with an M4 screw is suggested.
USB Storage Port (Type A Connector) Pinouts
Pin
Description
1
VCC (+5V)
2
D– (Data -)
3
D+ (Data+)
4
GND (Ground)
10/100BaseT(X) Ethernet Port Connection
The 10/100BaseT(X) ports located on the EDS-510E’s front panel are
used to connect to Ethernet-enabled devices. Most users configure these
ports for Auto MDI/MDI-X mode, in which case the port’s pinouts are
adjusted automatically depending on the type of Ethernet cable used

- 10 -
(straight-through or cross-over), and the type of device (NIC-type or
HUB/Switch-type) connected to the port.
In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports. We also give cable wiring diagrams for
straight-through and cross-over Ethernet cables.
RJ45 (8-pin, MDI) Port Pinouts
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
RJ45 (8-pin, MDI-X) Port Pinouts
Pin
Signal
1
Rx+
2
Rx-
3
Tx+
6
Tx-
RJ45 (8-pin) to RJ45 (8-pin) Straight-through Cable Wiring
RJ45 (8-pin) to RJ45 (8-pin) Cross-over Cable Wiring
1000BaseT Ethernet Port Connection
1000BaseT data is transmitted on differential TRD+/- signal pairs over
copper wires.
MDI/MDI-X Port Pinouts
Pin
Signal
1
TRD(0)+
2
TRD(0)-
3
TRD(1)+
4
TRD(2)+
5
TRD(2)-
6
TRD(1)-
7
TRD(3)+
8
TRD(3)-