Moxa Technologies IEX-408E-2VDSL2-HV User manual

P/N: 1802004082010
*1802004082010*
IEX-408E-2VDSL2 Series
Quick Installation Guide
Moxa Managed VDSL2 Ethernet Extender Switch
Edition 1.0, April 2016
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2016 Moxa Inc. All rights reserved.
www.ipc2u.ru
www.moxa.pro

Overview
The IEX-408E-2VDSL2 is an industrial managed Ethernet extender switch
for establishing long distance Ethernet transmissions over twisted-pair
copper wiring. IEX-408E-2VDSL2 units can easily be linked in series to
form a long distance multi-drop configuration, with one
IEX-408E-2VDSL2 unit located at each drop-point. Adjacent drop-points
can be separated theoretically by up to 3 km, with a transmission speed of
1 Mbps achieved using a VDSL2 connection (with a connection distance of
300 m, a transmission speed of 100Mbps can be theoretically achieved).
Each IEX-408E-2VDSL2 unit provides six 10/100BaseT(X) and two DSL
ports, giving users an incredible amount of flexibility for linking together
a wide variety of devices separated by vast distances. With its compact
DIN-rail design, the IEX-408E-2VDSL2 series is perfect for use in harsh
operating environments with limited installation space.
Redundancy is provided by Turbo Ring, Turbo Chain, RSTP/STP, and
MSTP, and a state-of-the-art controllable bypass solution on the DSL
ports increases the system reliability and availability of your network.
To simplify configuration, the IEX-408E-2VDSL2 uses CO/CPE automatic
negotiation (the factory default setting). The device will automatically
adjust CO/CPE status to each DSL connection pair of IEX devices to
enable a touch-free of settings.
www.ipc2u.ru
www.moxa.pro

Package List
The Moxa IEX-408E-2VDSL2 is shipped with the following items. If any of
these items are missing or damaged, please contact your customer
service representative for assistance.
•1 IEX-408E-2VDSL2 Extender Switch
•USB Cable: CBL-USBA/B-100
•Protective caps for unused ports
•Documentation and software CD
•Quick installation guide (printed)
•Warranty card
Feature Highlights
•6 10/100BaseT(X) Fast Ethernet ports and 2 DSL (VDSL2 technology)
ports for long distance copper connections (up to 100Mbps @ ~300m
and up to 3km @ ~1Mbps over twisted-pair copper wires)
•Automatic CO/CPE negotiation reduces configuration time
•Turbo Ring / Turbo Chain on both Fast Ethernet and DSL ports for fast
recovery
•Controllable bypass mode on DSL ports gives higher availability in a
daisy chain topology
•Port Trunking on Ethernet and DSL ports for optimum bandwidth
utilization
•RADIUS, TACACS+, SNMPv3, IEEE 802.1X, HTTPS, and SSH to
enhance network security
•Flexible deployment with 2-pin or RJ11/45 connector on DSL ports
•Easy network management by web browser, Telnet/serial console,
Windows utility, ABC-02-USB, and MXview
•Universal power supply options
Universal high-voltage (HV) model (IEX-408E-2VDSL2-HV):
110/220 VDC/VAC (88 to 300 VDC, 85 to 264 VAC)
Redundant dual inputs low-voltage (LV) model
(IEX-408E-2VDSL2-LV): 12/24/48 VDC (9.6 to 60 VDC)
www.ipc2u.ru
www.moxa.pro

IEX-408E-2VDSL2 Panel Layout
Front Panel:
1. USB storage port (type A
connector)
2. 1 to 6: 10/100BaseT(X) port
3. 1 to 6 port status LED
•Upper LED: 100 Mbps
•Lower LED: 10 Mbps
4. System status LED:
•STATE LED indicator
•PWR1 LED indicator
•PWR2 LED indicator
•DSL BYPASS LED indicator
•FAULT LED indicator
•MSTR/HEAD LED indicator
•CPLR/TAIL LED indicator
5. D1 to D2: DSL port
6. DSL port (RJ-45/RJ-11
connector)
7. DSL port (Detachable 2-pin
terminal block)
8. D1 to D2 DSL port st
atus LED:
•CO/CPE LED indicator
•LNK/ACT LED indicator
9. 3-pin-DIP-switch for
controlling DSL Bypass mode
10.
Door screw
11.
Model name
Top Panel
:
1. RESET button
2. 4-pin terminal receptor for
relay output and digital input
3. USB console port (type B
connector)
4. 4-pin-DIP-switch for Turbo
Ring, Ring Master, and Ring
Coupler
5. Grounding screw (chassis
ground)
6. 5-pin terminal receptor for
power input(s)
•Universal high-voltage
(HV) model
(IEX-408E-2VDSL2-HV):
110/220 VDC/VAC (PWR
1)
•Redundant dual inputs
low-voltage (LV) model
(IEX-408E-2VDSL2-LV):
12/24/48 VDC (PWR 1)
and 12/24/48 VDC (PWR
2)
www.ipc2u.ru
www.moxa.pro

Rear Panel:
1.
Screw holes for wall mounting
kit
2. DIN-rail mounting kit
Mounting Dimensions - unit = mm (inches)
www.ipc2u.ru
www.moxa.pro

DIN-Rail Mounting
The metal DIN-rail mounting kit is fixed to the back panel of the
IEX-408E-2VDSL2. Mount the IEX-408E-2VDSL2 on the corrosion-free
mounting rail that meets the EN 60715 standard.
Installation
STEP 1—Insert the upper lip of
the DIN
-rail kit into the
mounting rail.
STEP 2
—Press the
IEX
-408E-2VDSL2 towards the
mounting rail until it snaps into
place.
Removal
STEP 1—Pull down the latch on
the DIN
-rail kit with a
screwdriver.
STEP 2 & 3
—Slightly pull the
IEX
-408E-2VDSL2 forward and
lift up to remove it from the
mounting rail.
Wall-Mounting (optional)
For some applications, you will find it convenient to mount the Moxa
IEX-408E-2VDSL2 on the wall, as shown in the following figures in this
section. Please follow below illustrations to install.
STEP 1—Remove the DIN rail attachment plate from the rear panel of the
IEX-408E-2VDSL2, and then attach the wall mount plates with M3 screws,
as shown in the figure below.
www.ipc2u.ru
www.moxa.pro

STEP 2—Mounting the IEX-408E-2VDSL2 on the wall
requires 4 screws. Use the
IEX-408E-2VDSL2
, with wall
mount plates attached, as a guide to mark the location
of the 4 screws. The heads of the screws should be less
than 6.0 mm in diameter, and the shafts should be less
than 3.5
mm in diameter, as shown in the figure on
the
right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw into one
of the keyhole-shaped apertures of the wall mounting plates.
STEP 3—Do not tighten the screws completely—leave about 2 mm to
allow room for sliding the wall mount panel between the wall and the
screws.
STEP 4—Once the screws are fixed
into the wall, insert the four screw
heads through the large parts of the
keyhole
-shaped ap
ertures, and then
slide the IEX
-408E-2VDSL2
downwards, as indicated in the
figure
on
the right. Tighten the four
screws for added stability.
Wiring Requirement
ATTENTION
Safety First!
Be sure to disconnect the power cord
before installing and/or
wiring your Moxa Ethernet Extender Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Be sure to read and follow these important guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE
Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
•You should separate input wiring from output wiring.
•We advise that you label the wiring to all devices in the system.
www.ipc2u.ru
www.moxa.pro

Grounding the Moxa IEX-408E-2VDSL2 Ethernet
Extender Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw (chassis ground) to the grounding surface prior to
connecting devices.
ATTENTION
This product is intended to be mounted onto a well
-grounded
mounting surface, such as a metal panel.
ATTENTION
Before powering on the IEX
-408E-2VDSL2, make sure that the
grounding cable is secured between the grounding screw (chassis
ground)
and the ground for surge protection (surge ground)
on
the 5
-pin terminal block for power inputs. Ground for surge
protection is on terminal 3 of the terminal block as shown below.
ATTENTION
For dielectric strength (HIPOT) test, users must remove the
grounding cable secured between the grounding screw (chassis
ground)
and ground for surge protection (surge ground)
located
at terminal 3 of the terminal block to avoid damage.
Wiring the Relay Contact
The IEX-408E-2VDSL2 has one set of relay outputs. These relay output
use two contacts of the 4-pin terminal block on the IEX-408E-2VDSL2’s
top panel.
Refer to the instructions below on how to connect the wires to the
terminal block connector, and how to attach the terminal block connector
to the terminal block receptor.
STEP 1—Insert the two wires into the RELAY terminals respectively to
form an open circuit.
STEP 2—To keep the RELAY wires from coming loose , use a small
flathead screwdriver to tighten the wire-clamp screws on the front of the
terminal block connector.
www.ipc2u.ru
www.moxa.pro

STEP 3—Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the IEX-408E-2VDSL2’s top
panel.
FAULT:
The two contacts of the 4-pin terminal block connector are used to detect
user-configured events. The two wires attached to the fault contacts form
an open circuit when a user-configured event is triggered. If a
user-configured event does not occur, the fault circuit remains closed.
Wiring the Digital Input
The IEX-408E-2VDSL2 has one set of digital input (DI). The DI consists of
two contacts of the 4-pin terminal block on the IEX-408E-2VDSL2’s top
panel, which are used for the two DC inputs.
Refer to the instructions below on how to connect the wires to the
terminal block connector, and how to attach the terminal block connector
to the terminal block receptor.
STEP 1: Insert the negative (ground)/positive DI wires into the ┴/I
terminals, respectively.
STEP 2: To keep the DI wires from coming loose, use a small flathead
screwdriver to tighten the wire-clamp screws on the front of the terminal
block connector.
STEP 3: Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the IEX-408E-2VDSL2’s top
panel.
Wiring the Power Input (Universal high-voltage
(HV) model: 110/220 VDC/VAC)
The IEX-408E-2VDSL2 HV model (110/220 VDC/VAC) has one set of
power inputs (PWR 1)—Pin 1(V+/Line) and Pin5 (V-/Neutral). Insert the
5-pin terminal block connector prongs into the terminal block receptor on
IEX-408E-2VDSL2 HV unit properly. The top and front views of the
terminal block connector are also shown below.
www.ipc2u.ru
www.moxa.pro

Take the following steps to wire the power input:
STEP 1: Insert the Line/Neutral AC or Positive/Negative DC wires into the
terminals (Terminal 1 for Line/Positive and Terminal 5 for
Neutral/Negative) of the terminal block connector.
STEP 2: To keep the AC or DC wires from coming loose, use a small
flathead screwdriver to tighten the wire-clamp screws on the front of the
terminal block connector.
STEP 3: Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the IEX-408E-2VDSL2 HV
unit’s top panel.
NOTE
The IEX-408E-2VDSL2 HV model (110/220 VDC/VAC) has the
reverse protection mechanism for 110/220 VDC input.
ATTENTION
Before connecting the
IEX-408E-2VDSL2 HV model to the DC
power input, make sure the DC power source voltage is stable.
Wiring the Redundant Power Inputs (low-voltage
(LV) model: 12/24/48 VDC)
The IEX-408E-2VDSL2 LV model (12/24/48 VDC) has two sets of power
inputs –power input 1 (PWR 1) and power input 2 (PWR 2). Insert the
5-pin terminal block connector prongs into the terminal block receptor on
IEX-408E-2VDSL2 LV unit properly. Please take the following steps to
wire the redundant power inputs. The top and front views of the terminal
block connector are also shown below.
Take the following steps to wire the redundant power inputs:
STEP 1: Insert the Positive/Negative DC wires into the V1+/V1- terminal
for PWR 1 and/or V2+/V2- terminal for PWR 2.
STEP 2: To keep the DC wires from coming loose, use a small flathead
screwdriver to tighten the wire-clamp screws on the front of the terminal
block connector.
STEP 3: Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the IEX-408E-2VDSL2 LV
unit’s top panel.
ATTENTION
Before connecting the
IEX-40E-
2VDSL2 to the DC power inputs,
make sure the DC power source voltage is stable.
www.ipc2u.ru
www.moxa.pro