Moxa Technologies PT-7710 Series Manual

Moxa PowerTrans Switch
PT-7710 Series
Hardware Installation Guide
Third Edition, July 2010
©2010 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan,
R.O.C.
TEL: [phone]
P/N: 1802077100012

- 2 -
Package Checklist
The Moxa PowerTrans switch is shipped with the following items. If any of
these items are missing or damaged, please contact your customer service
representative for assistance.
y1 Moxa PowerTrans Switch
yHardware Installation Guide
yCD-ROM with User’s Manual and SNMP MIB file
yMoxa Product Warranty Statement
yRJ45 to DB9 console port cable
yProtective caps for unused ports
y2 rack-mount ears or wall-mount ears
Panel Layout
CONSOLE
PT-7710
8
9
11
2
4Front View (Front Cabling)
Rear View (Front Cabling)
Top View (Down Cabling)
MODE
LNK/ACT SPEED FDX/HDX
FAULT MASTER COUPLER
STAT PWR1 PWR2
RING PORT COUPLER
PORT
37
48 2 6
1 5 M1
7
8
26
15
M2
4
35
2
2
1
1
PT-7710
13
24
57
68
M2M1
MODE
LNK/ACT SPEED FDX/HDX
FAULT MASTER COUPLER
STAT PWR1 PWR2
RINGPORT COUPLER
PORT
37
48 2 6
1 5
M1
3
48
26
1
37
8
26
5
3
15
57631 10
1. System status LEDs
2. Interface Module mode LEDs
3. Interface Module port LEDs
4. Push-button switch to select mode for Interface Module
5. Model Name
6. Fast Ethernet Interface Modules
7. Gigabit Ethernet Interface Modules
8. Serial Console port
9. 10-pin terminal block for power inputs, and relay output
10. Rack Mounting Kit
11. Wall Mounting Kit

- 3 -
Dimensions (unit = mm)
31.8
462.5
266.5
Rear View
Top View
Side View Side View
Front View
219.3
31.8
44
195
209.4
31.8
44
24.3
Fast Ethernet Interface Modules
(for slot 1)
40.7
96.8
PM-7200-8TX
96.8
40.7
PM-7200-1LSC6TX
40.7
96.8
PM-7200-4MSC2TX/PM-7200-4SSC2TX
96.8
40.7
PM-7200-6MSC/PM-7200-6SSC
96.8
40.7
PM-7200-2MSC4TX/PM-7200-2SSC4TX PM-7200-4MST2TX
40.7
96.8
PM-7200-6MST
96.8
40.7
PM-7200-2MST4TX
96.8
40.7
96.8
40.7
PM-7200 1MST6TX
PM-7200-8SFP
96.8
40.7
40.7
96.8
PM-7200 1SSC6TX/1MSC6TX
40.7
96.8
PM-7200-4M12
40.7
96.8
PM-7200 4MST-FL
40.7
96.8
PM-7200 8MTRJ
40.7
96.8
PM-7200 6MTRJ
40.7
96.8
PM-7200 2MTRJ

- 4 -
Gigabit/Fast Ethernet Interface
Modules (for slot 2)
40.7
86.6
PM-7200-2GTXSFP
40.7
86.6
PM-7200 1MSC/1SSC
40.7
86.6
PM-7200 1MST
PM-7200 2MSC/2SSC
40.7
86.6
PM-7200 2MST
40.7
86.6
Rack Mounting
Use four screws to attach the PT switch to a standard rack.
Use four screws to attach the PT switch to a
standard rack.
Wall Mounting
Use four screws to attach the PT switch to a Moxa wall mounting kit.
Wiring Requirements
WARNING Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa PowerTrans Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Grounding Moxa PowerTrans Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.

- 5 -
Wiring the Power Inputs
The PT series of switches supports dual redundant power supplies (DC power
only): VDC “Power Supply 1 (PWR1)” and “Power Supply 2 (PWR2)”, or
VAC “Power Supply (PWR1)”. The connections for PWR1, PWR2 and the
RELAY are located on the terminal block. The front view of the terminal block
connectors are shown below.
Wiring the Relay Contact
Each PT switch has one relay output. Refer to the next section for detailed
instructions on how to connect the wires to the terminal block connector, and
how to attach the terminal block connector to the terminal block receptor.
FAULT: The relay contact of the 10-pin terminal block connector are used to
detect user-configured events. The two wires attached to the RELAY contacts
form an open circuit when a user-configured event is triggered. If a
user-configured event does not occur, the RELAY circuit will be closed.
Wiring the Redundant Power Inputs
Each PT switch has two sets of power inputs: power input 1 and power input 2.
STEP 1: Insert the dual set positive/negative DC wires into PWR1 and PWR2
terminals (+ →pins 1, 9, - →pins 2, 10). Or insert the L/N AC wires into
the PWR1 terminals (L →pin 1, N →pin 2).
STEP 2: To keep the DC or AC wires from pulling loose, use a screwdriver to
tighten the wire-clamp screws on the front of the terminal block connector.

- 6 -
LED Indicators
The front panel of the PT switch contains several LED
indicators. The function of each LED is described in the table
below.
LED Color State Description
System LEDs
STAT
GREEN
On System has passed self-diagnosis test
on boot-up and is ready to run.
Blinking System is undergoing the
self-diagnosis test.
RED On
System failed self-diagnosis on
boot-up.
PWR1 AMBER
On Power is being supplied to the main
module’s power input PWR1.
Off Power is not being supplied to the
main module’s power input PWR1.
PWR2 AMBER
On Power is being supplied to the main
module’s power input PWR2.
Off Power is not being supplied to the
main module’s power input PWR2.
FAULT RED
On
The corresponding PORT alarm is
enabled and a user-configured event
has been triggered.
Off
The corresponding PORT alarm is
enabled and a user-configured event
has not been triggered, or the
corresponding PORT alarm is
disabled.
MSTR/HEAD GREEN
On
This PT switch is set as the Master
of the Turbo Ring, or as the Head of
the Turbo Chain.
Blinking
The PT switch has become the Ring
Master of the Turbo Ring, or the
Head of the Turbo Chain, after the
Turbo Ring or the Turbo Chain went
down.
Off
The PT switch is not the Master of
this Turbo Ring or is set as a
Member of the Turbo Chain.
CPLR/TAIL GREEN
On
When this PT switch is enabled to
form a back-up path, or it is set as
the Tail of the Turbo Chain.
Blinking Turbo Chain is down.
Off
This PT switch disabled the coupling
function, or is set as a Member of the
Turbo Chain.
Mode LEDs
LNK/ACT GREEN On
The corresponding module

- 7 -
port’s link is active.
Blinking
The corresponding module
port’s data is being
transmitted.
Off The corresponding module
port’s link is inactive.
SPEED GREEN
Off The corresponding module port’s
data is bein
g
transmitted at 10 Mb
p
s.
On
The corresponding module port’s
data is being transmitted at 100
Mb
p
s.
Blinking
The corresponding module port’s
data is being transmitted at
1000 Mb
p
s.
FDX/HDX GREEN
On
The corresponding module port’s
data is being transmitted in full
du
p
lex mode.
Off
The corresponding module port’s
data is being transmitted in half
du
p
lex mode.
RING/CHAIN
PORT GREEN
On
The corresponding module’s port is
the ring or chain port of this PT
switch.
Off
The corresponding module’s port is
not the ring or chain port of this PT
switch.
COUPLER
PORT GREEN
On The corresponding module’s port is
the cou
p
ler
p
ort of this PT switch.
Off
The corresponding module’s port is
not the coupler port of this PT
switch.
* Slot 2 (M2) is mainly used for Gigabit modules. If
100BaseFX modules are used in Slot 2 (M2), the modules will
not support “Far End Fault”. The Link/ACT LED indicator will
stay at “Green (ON)” status when Fiber TX cable is unplugged.
Specifications
Technology
Standards IEEE 802.3, 802.3u, 802.3ab, 802.3z, 802.3x, 802.1D,
802.1W, 802.1Q, 802.1p, 802.1X, 802.3ad
Flow control IEEE 802.3x flow control, back pressure flow control
Interface
Fast Ethernet Slot 1 (M1) for any combination of 4-,6-, 7-, or 8-port
PM-7200 fast Ethernet modules with 10/100BaseT(X)
(TP/M12 interface) or 100BaseFX (SC/ST connector),
or 100BaseSFP; Slot 2 (M2) for a 1- or 2-port interface
modules with 100BaseFX (SC/ST connector)
Gigabit Ethernet Slot 2 (M2) for 2-port PM-7200 Gigabit Ethernet
combo module with 100/1000BaseT(X) or
1000BaseSFP slots (Slot 2 does not support 10M
FDX/HDX)
Console RS-232 (RJ45)
System LED STAT, PWR1, PWR2, FAULT, MSTR/HEAD,

- 8 -
Indicators CPLR/TAIL
Mode LED
Indicators LNK/ACT, FDX/HDX, RING/CHAIN PORT, COUPLER PORT, SPEED
Alarm Contact One relay output with current carrying capacity of 3A
@ 30 VDC or 3A @ 240 VAC
Optical Fiber (100BaseFX)
Distance Multi-mode
0 to 5 km, 1300 nm (50/125μm, 800 MHz*km)
0 to 4 km, 1300 nm (62.5/125μm, 500 MHz*km)
Single-mode
0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))
Min. TX Output M Mu ul l
t
ti i- -
m
mo od de e: : - -2 20 0 d dB B
m
m; ; s si in n
g
gl le e- -
m
mo od de e: : - -5 5 d d
b
b
m
m
Max. TX Output M Mu ul l
t
ti i- -
m
mo od de e: : - -1 10 0 d dB B
m
m; ; s si in n
g
gl le e- -
m
mo od de e: : 0 0 d d
b
b
m
m
RX Sensitivity M Mu ul l
t
ti i- -
m
mo od de e: : - -3 32 2 d dB B
m
m; ; s si in n
g
gl le e- -
m
mo od de e: : - -3 34 4 d d
b
b
m
m
Power
Input Voltage 24/48 VDC (9 to 60 V), or 110/220 VDC/VAC (88 to
300 VDC and 85 to 264 VAC)
Input Current Max. 0.81A @ 24 VDC
Max. 0.42A @ 48 VDC
Max. 0.17/0.10 @ 110/220 VDC
Max. 0.20/0.12 @ 110/220 VAC
Physical Characteristics
Housing IP 30 protection, metal case
Dimensions
(W x H x D) 266.7 x 44 x 195 mm (10.5 x 1.73 x 7.68 in.)
Weight 2200g
Regulatory Approvals
Operating Temp. -40 to 85°C (-40 to 185°F)
Cold start of min. 100 VAC at -40°C
Storage Temp. -40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity. 5 to 95% (non-condensing)
Regulatory Approvals
Safety EN60950-1
Power Automation IEC 61850-3, IEEE 1613
Road Traffic NEMA TS2
Rail Traffic EN50121-4
EMI FCC Part 15, CISPR (EN55022) class A
Warranty 5 years
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel: [phone]
Fax: [phone]
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel: [phone]
Fax: [phone]
Moxa Europe:
Tel: [phone]
Fax: [phone]
Moxa Asia-Pacific:
Tel: [phone]
Fax: [phone]