Moxa Technologies EtherDevice EDS-405A-PN User manual

2014 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
P/N: 1802004000018
EDS-405A/408A Series
Hardware Installation Guide
Moxa EtherDevice™ Switch
Ninth Edition, December 2014

- 2 -
Overview
The Moxa EtherDevice™ EDS-405A/408A series, which includes both 5
and 8-port smart Ethernet switches, is a cost-effective solution for your
Ethernet connections. In addition, the built-in smart alarm function helps
system maintainers monitor the health of your Ethernet network.
Package Checklist
The Moxa EDS-405A/408A switches are shipped with the following items.
If any of these items is missing or damaged, please contact your
customer service representative for assistance.
•EDS-405A or EDS-408A Ethernet switch
•RJ45-to-DB9 console port cable
•Protective caps for unused ports
•Panel mounting kit (optional—must order separately)
•Hardware installation guide
•CD-ROM with user’s manual and Windows utility
•Warranty card

- 3 -
EDS-405A/408A Panel Layout (standard)
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation vents
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD: LED indicator
10.
CPLR/TAIL: LED indicator
11.
TP port’s 100 Mbps LED
12.
TP port’s 10 Mbps LED
13.
Model Name
14.
10/100BaseT(X) ports
15.
Screw hole for wall mounting kit
16.
DIN-Rail kit

- 4 -
EDS-405A/408A-MM (SC-type) Panel Layout
NOTE:
T
he appearance of the EDS-405A-SS-SC is
identical to
that of the EDS-405A-MM-SC.
T
he appearance of the EDS-408A-SS-SC is
identical to
that of the EDS-408A-MM-SC.
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation vents
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD: LED indicator
10.
CPLR/TAIL: LED indicator
11.
TP port’s 100 Mbps LED
12.
TP port’s 10 Mbps LED
13.
Model Name
14.
10/100BaseT(X) ports
15.
100BaseFX ports
16.
FX port’s 100 Mbps LEDs
17.
Screw hole for wall mounting kit
18.
DIN-Rail kit

- 5 -
EDS-405A/408A-MM (ST-type) Panel Layout
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Heat dissipation vents
4. Console port
5. DIP switches
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD: LED indicator
10.
CPLR/TAIL: LED indicator
11.
TP port’s 100 Mbps LED
12.
TP port’s 10 Mbps LED
13.
Model Name
14.
10/100BaseT(X) ports
15.
100BaseFX ports
16.
FX port’s 100 Mbps LEDs
17.
Screw hole for wall mounting kit
18.
DIN-Rail kit

- 6 -
EDS-408A-3M Panel Layout (SC/ST-type)
NOTE:
The appearance of
the
EDS
-408A-3S-SC,
EDS
-408A-1M2S-SC, and
EDS
-408A-2M1S-SC are identical to
that of
the EDS-408A-3M-SC.
1. Grounding screw
2. Terminal block for power input
PWR1/PWR2 and relay output
3. Console port
4. DIP switches
5. Heat dissipation vents
6. Power input PWR1 LED
7. Power input PWR2 LED
8. Fault LED
9. MSTR/HEAD: LED indicator
10.
CPLR/TAIL: LED indicator
11.
10/100BaseT(X) ports
12.
TP port’s 100 Mbps LED
13.
TP port’s 10 Mbps LED
14.
100BaseFX ports
15.
1 FX port’s 100Mbps LEDs
100M-M: multi mode FX port
100M-S: single mode FX port
16.
Model Name
17.
Screw hole for wall mounting kit
18.
DIN-Rail kit

- 7 -
Mounting Dimensions (unit = mm)
Unit = mm (inch)

- 8 -
DIN-Rail Mounting
The aluminum DIN-Rail attachment plate should already be fixed to the
back panel of the EDS-405A/408A when you take it out of the box. If you
need to reattach the DIN-Rail attachment plate, make sure the stiff metal
spring is situated towards the top, as shown in the following figures.
STEP 1:
Insert the top of the DIN
-Rail into
the slot just
below the stiff metal
spring.
STEP 2:
The DIN
-Rail attachment unit will
snap into place as shown.
To remove the Moxa EtherDevice switch from the DIN-Rail, simply
reverse Steps 1 and 2.
Wall Mounting (optional)
For some applications, you will find it convenient to mount the
EDS-405A/408A on the wall, as shown in the following figures.
STEP 1:
Remove the aluminum
DIN
-Rail attachment plate
from
the EDS-405A/408A’s
rear panel, and then attach
the wall mount plates
with
M3 screws
, as shown in the
diagram
at the right.
STEP 2:
Mounting
the EDS-405A/408
A on the wall requires 4
screws. Use the
switch, with wall mount plates
attached, as a guide to mark the correct locations of
the 4 screws. The heads of the screws should be less
than 6.0 mm in diameter, and the shafts should be
less than 3.5
mm in diameter, as shown in the figure
at the right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw into one
of the keyhole-shaped apertures of the wall mounting plates.
Do not screw the screws in completely—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.
STEP 3: Once the screws are fixed in the wall, insert the four screw heads
through the large parts of the keyhole-shaped apertures, and then slide
the EDS-405A/408A downwards, as indicated. Tighten the four screws for
added stability.

- 9 -
ATEX Information
1. Certificate number: DEMKO 08 ATEX
0712961X
2. Ambient range (-40°C ≤Tamb ≤75°C
)
3. Certification string:
EDS-405A: Ex nA nC IIC T4 Gc
EDS-408A: EX nA nC op is IIC T4 Gc
4. Standards covered ( EN 60079-0:2012, EN 60079-15:2010)
5. The conditions of safe usage:
•These products must be mounted in an IP54 enclosure.
•Install in an area of pollution degree 2 or less.
•Use a conductor wire of size 0.2 mm² or greater.
•PROVISIONS SHOULD BE MADE,
EXTERNAL TO THE APPARATUS,
TO PREVENT THE RATED VOLTAGE FROM BEING EXCEEDED BY
TRANSIENT DISTURBANCES OF MORE THAN 40%.
Wiring Requirements
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your
Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Be sure to read and follow these important guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
•Use the type of signal transmitted through a wire to determine which
wires should be kept separate. The rule of thumb is that wiring that
shares similar electrical characteristics can be bundled together.
•Keep input wiring and output wiring separate.
•When necessary, you should label the wiring to all devices in the
system.
Grounding the EtherDevice Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.

- 10 -
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface, such as a metal panel.
Wiring the Relay Contact
The Relay Contact consists of the two middle contacts of the terminal
block on the EDS-405A/408A’s top panel. Refer to the next section for
detailed instructions on how to connect the wires to the terminal block
connector, and how to attach the terminal block connector to the terminal
block receptor.
In this section, we explain the meaning of the two contacts used to
connect the Alarm Contact.
FAULT: The two middle contacts of the
6
-contact terminal block connector
are used to
detect both power faults and port faults. The
two wires attached to the
fault contacts form
a
n open circuit when:
A relay warning event
is triggered.
OR
T
he EDS-405A/408A is
the Master of this Turbo
Ring, and the Turbo Ring
is broken.
OR
There is a s
tart-up failure.
If
none of these three conditions is satisfied,
the fault circuit will remain closed.
Wiring the Redundant Power Inputs
The top two contacts and the bottom two contacts of the 6-contact
terminal block connector on the EDS-405A/408A’s top panel are used for
the EDS-405A/408A’s two DC inputs. Top and front views of one of the
terminal block connectors are shown in the following figures:
STEP 1: Insert the negative/positive DC wires
into the
V-/V+ terminals, respectively.
STEP 2:
To keep the DC wires from pulling
loose, use a small flat
-blade screwdriver to
tighten the wire
-clamp screws on the front of
the termi
nal block connector.
STEP 3:
Insert the plastic terminal block
connector prongs into the terminal block
receptor, which is
located on the
EDS-405A/408A’s top panel.
ATTENTION
Before connecting
the EDS-405A/408A to the DC power inputs,
make sure the DC power source voltage is stable.