Moxa Technologies EDS-2010-ML Series User manual

P/N: 1802020003011
*1802020003011*
EDS-2010/2018-ML Series
Quick Installation Guide
Moxa EtherDevice Switch
Version 1.1, August 2019
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2019 Moxa Inc. All rights reserved.

- 2 -
Overview
The EDS-2010/2018-ML series of industrial Ethernet switches are
equipped with 8/16-ports 10/100M copper ports and 2
10/100/1000BaseT(X) or 100/1000BaseSFP combo ports. The switches
are ideal for applications that require high-bandwidth data convergence
and long-distance uplinks.
The EDS-2010/2018-ML provides 12/24/48 VDC redundant power
inputs, and the switches are available with a standard operating
temperature range from -10 to 60°C, or with a wide operating
temperature range from -40 to 75°C. The switches are rugged enough
to operate reliably in harsh industrial environments.
To provide greater versatility for use with applications from different
industries, the EDS-2010/2018-ML also allow users to enable or disable
broadcast storm protection, Quality of Service (QoS) function, and port
break alarm function with DIP switches on the outer panel.
The EDS-2010/2018-ML switches can be easily installed with DIN-Rail
mounting as well as distribution boxes. The DIN-rail mounting
capability and IP30 metal housing with LED indicators make the plug-
and-play EDS-2010/2018-ML switches reliable and easy to use.
NOTE
Throughout this Quick Installation Guide, we use EDS as an
abbreviation for Moxa EtherDevice Switch:
EDS = Moxa EtherDevice Switch
ATTENTION
This device complies with part 15 of FCC Rules. Operation is
subject
to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Package Checklist
Your EDS is shipped with the following items. If any of these items are
missing or damaged, please contact your customer service
representative for assistance.
•Moxa EtherDevice™ Switch
•Quick installation guide (printed)
•Warranty card
•Protective caps for unused ports

- 3 -
Features
High Performance Network Switching Technology
•10/100/1000BaseT(X), 10/100BaseT(X) auto-negotiation speed,
full/half duplex mode, auto MDI/MDI-X connection, and
100/1000Base SFP slot.
•IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X), IEEE
802.3ab for 1000BaseT, and IEEE 802.3z for 1000BaseX.
•IEEE 802.1p for Quality of Service (QoS) traffic prioritized function.
•Store-and-forward switching process type.
Industrial-grade Reliability
•Power failure, port break alarm by relay output
•Redundant dual DC power inputs
•Broadcast storm protection to prevent network devices from
crashing
Rugged Design
•Operating temperature range from -10 to 60°C, or extended
operating temperature from -40 to 75°C for “-T” models
•IP30, rugged high-strength case
•DIN-rail or panel mounting ability
WARNING
The
power for this product is intended to be supplied by a
Listed Power Supply, with output marked LPS, and rated to
deliver 12 to 48 VDC at a maximum
of 0.62 A.
The DC
jack should be used with an LPS unit that is rated to
deliver 12 to 48 VDC at a minimum of 1.1A. The product should
not be disassembled by operators or service people.

- 4 -
Panel Layout of EDS-2010-ML-2GTXSFP / EDS-
2018-ML-2GTXSFP
1. Grounding screw
2. Terminal block for power input
(PWR1, PWR2) and relay output
3. DIP switch
4. Power input PWR1 LED
5. Power input PWR2 LED
6. Fault LED
7. Port number
8. 10/100 BaseT(X) Port
9. TP port’s 100 Mbps LED
10. TP port’s 10 Mbps LED
11. 10/100/1000 BaseT(X) Port
12. TP port’s 1000 Mbps LED
13. TP port’s 100 Mbps LED
14. 100/1000Base SFP slot
15. SFP port's 100/1000 Mbps LED
16. Model Name

- 5 -
Mounting Dimensions
EDS-2010-ML Series
EDS-2018-ML Series

- 6 -
DIN-rail Mounting
There are two options for DIN-rail mounting that can be used on an
EDS. Option 1 is the default type when the product is shipped.
Option 1 (Default):
When shipped, the metal DIN-rail mounting kit is fixed to the back
panel of the EDS. Mount the EDS on the corrosion-free mounting rail
that adheres to the EN 60715 standard.
Suggested Installation Method
STEP 1:
Insert the upper lip of the DIN
-
rail kit into the mounting rail.
S
TEP 2:
Press the device towards the
mounting rail until it snaps into
place.
Suggested Removal Method
STEP 1:
Pull down the latch on the DIN
-
rail kit with a screwdriver.
STEP 2:
Slightly pull the device forward
and lift up to remove it from the
mounting rail.
Option 2 (when side cabling is needed):
The metal DIN-rail mounting kit can be fixed to the side panel (mold
side) of the EDS (horizontal or vertical). Mount the EDS on the
corrosion-free mounting rail that adheres to the EN 60715 standard.

- 7 -
Suggested Installation Method
STEP 1:
Detach the metal DIN-rail mounting kit from the back panel and attach
it to the side panel (mold side) in either the horizontal or vertical
direction as indicated in the figure below.
STEP 2:
Insert the upper lip of the DIN
-rail kit
into the mounting rail.
STEP 3:
Press the device towards the mounting
rail until it snaps into place
.
Suggested Removal Method
STEP 1:
Pull down the latch
on the DIN-rail kit
with a screwdriver.
STEP 2:
Slightly pull the device forward and lift
up to remove it from the mounting rail.
NOTE
Screws that are used to fix the DIN-rail kit on the EDS should
be securely fastened before mounting on the mounting
rail.
Please make sure that if you remove the DIN
-rail, it must be
securely fastened when it is reattached.

- 8 -
Wall Mounting (optional)
For some applications, you will find it convenient to mount EDS on the
wall, as illustrated below.
STEP 1:
Remove the aluminum DIN-Rail attachment plate from EDS’s rear
panel, and then attach the wall mount plates, as shown in the diagram
below.
EDS-2010-ML Series
EDS-2018-ML Series
STEP 2:
Mounting EDS
on the wall requires 4 screws. Use the
switch, with wall mount plates attached, as a guide
to mark the correct locations of the 4 screws. The
heads of the screws should be less than 6.0 mm in
diameter, and the shafts should be less than 3.5 mm
in diameter, as shown in the figure at the right.
NOTE
Before tightening screws into the wall, make sure the screw
head and shank size are suitable by inserting th
e screw into
one of the keyhole
-shaped apertures of the Wall Mounting
Plates.
Do not screw the screws in all the way—leave about 2 mm to allow
room for sliding the wall mount panel between the wall and the screws.
STEP 3:
Once the screws are fixed in the
wall, insert the four screw heads
through the large parts of the
keyhole
-shaped apertures, and
t
hen slide EDS downwards, as
indicated. Tighten the four
screws for added stability.
WARNING
1.
External metal parts are hot. Take necessary precautions if
it is necessary to touch.

- 9 -
Wiring Requirements
WARNING
Do not
disconnect modules or wires unless the power supply
has been switched off or the area is known to be non
-
hazardous.
The devices may only be connected to the supply
voltage shown on the type plate.
The devices are designed for operation with a
Safety Extra-L
ow
V
oltage. Thus, they may only be connected to the supply
voltage connections and to the signal contact with the
Safety
E
xtra-Low Voltages (SELV) in compliance with IEC950/
EN60950/ VDE0805.
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your
Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire
size.
If the current goes above the maximum ratings, the wiring
could overheat, causing serious damage to your equipment.
You should also pay attention to the following items:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power
wiring in the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb
is that wiring that shares similar electrical characteristics can be
bundled together.
•Keep input wiring and output wiring separated.
•It is strongly advised that you label wiring to all devices in the
system when necessary.

- 10 -
Grounding Moxa EtherDevice Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from
the ground screw to the grounding surface prior to connecting devices.
A 4 mm2conductor must be used when a connection to the external
grounding screw is utilized.
ATTENTION
This
product is intended to be mounted to a well-grounded
mounting surface, such as a metal panel.
Wiring the Alarm Contact
The Alarm Contact consists of the two middle contacts of the terminal
block on EDS’s top panel. You may refer to the next section for detailed
instructions on how to connect the wires to the terminal block
connector, and how to attach the terminal block connector to the
terminal block receptor. In this section, we explain the meaning of the
two contacts used to connect the Alarm Contact.
FAULT: The two middle contacts of the 6-
contact
terminal block connector are used to
detect both power faults and port faults. The
two wires attached to the Fault contacts form
a
n open circuit when:
1. The EDS has lost power from one of the
DC power inputs.
OR
2. One of the ports for which the
corresponding PORT ALARM DIP Switch
is set to ON is not properly connected.
If
neither of these two conditions is satisfied,
the Fault circuit will be closed.