Moxa Technologies WAC-1001 Series User manual

WAC-1001 User’s Manual
Fourth Edition, August 2015
www.moxa.com/product
© 2015 Moxa Inc. All rights reserved.
www.ipc2u.ru
www.moxa.pro

WAC-1001 User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2015 Moxa Inc., All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Amer
icas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
www.ipc2u.ru
www.moxa.pro

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview...........................................................................................................................................1-2
Package Checklist...............................................................................................................................1-2
Product Features ................................................................................................................................1-2
Product Specifications (WAC-1001 Rev 2.xx.x).......................................................................................1-3
Functional Design ...............................................................................................................................1-4
LED Indicators ............................................................................................................................1-4
Beeper.......................................................................................................................................1-4
Reset Button...............................................................................................................................1-4
Relay (Digital Output)..................................................................................................................1-5
2. Getting Started ................................................................................................................................. 2-1
First-time Installation and Configuration................................................................................................2-2
Function Map .....................................................................................................................................2-4
3. Web Console Configureation ............................................................................................................. 3-1
Web Browser Configuration..................................................................................................................3-2
Overview...........................................................................................................................................3-4
Basic Settings ....................................................................................................................................3-4
System Info Settings ...................................................................................................................3-4
Network Settings.........................................................................................................................3-5
Time Settings .............................................................................................................................3-6
Controller Settings..............................................................................................................................3-7
Basic WAC Settings .....................................................................................................................3-7
WLAN Security Settings ...............................................................................................................3-9
Advanced Settings............................................................................................................................3-10
SNMP Agent .............................................................................................................................3-10
Auto Warning Settings.......................................................................................................................3-11
System Log ..............................................................................................................................3-12
Syslog .....................................................................................................................................3-12
E-mail......................................................................................................................................3-14
Relay.......................................................................................................................................3-15
Trap ........................................................................................................................................3-15
Status.............................................................................................................................................3-17
System Log ..............................................................................................................................3-17
Relay Status.............................................................................................................................3-17
DI and Power Status..................................................................................................................3-18
Managed Device List..................................................................................................................3-18
LAN Status ...............................................................................................................................3-19
Maintenance ....................................................................................................................................3-19
Console Settings .......................................................................................................................3-19
Ping.........................................................................................................................................3-19
Firmware Upgrade.....................................................................................................................3-20
Config Import Export .................................................................................................................3-20
Load Factory Default..................................................................................................................3-22
Username/Password ..................................................................................................................3-22
Locate Device ...........................................................................................................................3-22
Misc. Settings ...........................................................................................................................3-23
Save Configuration ...........................................................................................................................3-23
Restart............................................................................................................................................3-24
Logout ............................................................................................................................................3-24
4. Software Installation and Configuration ........................................................................................... 4-1
Overview...........................................................................................................................................4-2
AWK Search Utility..............................................................................................................................4-2
Installing AWK Search Utility ........................................................................................................4-2
Configuring AWK Search Utility .....................................................................................................4-4
5. Other Console Considerations ........................................................................................................... 5-1
RS-232 Console Configuration (115200, None, 8, 1, VT100) ....................................................................5-2
Configuration by Telnet and SSH Consoles.............................................................................................5-3
Configuration by Web Browser with HTTPS/SSL......................................................................................5-4
Disabling Telnet and Browser Access.....................................................................................................5-5
A. References ........................................................................................................................................ A-1
Roaming Domain................................................................................................................................A-2
Roaming Method ................................................................................................................................A-3
Compare....................................................................................................................................A-3
B. Supporting Information .................................................................................................................... B-1
About This User’s Manual.....................................................................................................................B-2
DoC (Declaration of Conformity)...........................................................................................................B-3
www.ipc2u.ru
www.moxa.pro

Federal Communication Commission Interference Statement............................................................B-3
Firmware Recovery .............................................................................................................................B-3
www.ipc2u.ru
www.moxa.pro

1
1. Introduction
The WAC-1001 is rated to operate at temperatures ranging from 0 to 60°C for standard models and -40 to 75°C
for wide temperature models, and is rugged enough for any harsh industrial environment.
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

Product Specifications (WAC-1001 Rev 2.xx.x)

Functional Design
LED Indicators
Beeper
Reset Button
Relay (Digital Output)
www.ipc2u.ru
www.moxa.pro

WAC-1001 Introduction
1-2
Overview
The WAC-1001 Wireless Access Controller which is used to enabling layer 2 controller based roaming for the
RTG series. It is ideal for applications that are hard to wire, too expensive to wire, or use mobile equipment that
connects to a TCP/IP network. The WAC-1001 can operate at temperatures ranging from 0 to 60°C for standard
models and -40 to 75°C for extended temperature models, and is rugged enough for any harsh industrial
environment. Installation is easy, with either DIN-Rail mounting or wall mounting in distribution boxes. The
WAC-1001 with its wide operating temperature range, IP30-rated housing with LED indicators, and
DIN-Rail/wall mount is a convenient yet reliable solution for all types of industrial wireless applications.
Package Checklist
Moxa’s WAC-1001 is shipped with the following items. If any of these items is missing or damaged, please
contact your customer service representative for assistance.
•WAC-1001 series wireless controller
•1 cable holder with 1 screw
•2 protective caps
•Wall mount kit
•Quick installation guide
•Software CD
•Warranty card
NOTE
The above items come with the standard WAC
-
1001 model, but the package contents may vary for customized
versions.
Product Features
•Advanced Turbo Roaming Support
Less-than-50 ms handover
Wireless security: WPA/WPA2-Personal/Enterprise
•Central Management Functions
Wireless security setting
•Free firmware update for more advanced functions
•RS-232 console management
•2DI+1DO for on-site monitoring and warnings
•Wide -40 to 75°C operating temperature range (-T model)
•Redundant 24 VDC power inputs or IEEE802.3af Power over Ethernet
•DIN-Rail or wall mounting
•IP30-rated heavy-duty metal housing
www.ipc2u.ru
www.moxa.pro

WAC-1001 Introduction
1-3
Product Specifications (WAC-1001 Rev 2.xx.x)
WLAN Interface
Standards:
IEEE
802.1x (Radius client)
IEEE 802.3u for 10/100BaseT(X) for Ethernet
LAN
IEEE 802.3af for Power
-over-Ethernet
Supported Models:
• AWK
-3121-M12-RTG
•
AWK-3121-SSC-RTG
Interface
LAN Ports:
1, 10/100/1000BaseT(X), auto negotiation speed (RJ45-type)
Console for External Antenna:
RS-232 (RJ45-type)
LED Indicators:
PWR1, PWR2, PoE, FAULT, STATE, LAN
Alarm Contact:
1 relay output with current carrying capacity of 1 A @ 24 VDC
Digital Inputs:
2 electrically isolated inputs
• +13 to +30 V for state “1” (ON)
• +3 to
-30 V for state “0” (OFF)
• Max. input current: 8 mA
Physical Characteristics
Housing:
Metal, providing IP30 protection
Weight:
1060 g
Dimensions:
52.85 x 135 x 105 mm (2.08 x 5.31 x 4.13 in)
Installation:
DIN-Rail mounting, wall mounting (optional)
Environmental Limits
Operating Temperature:
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models:
-40 to 75°C (-40 to 167°F)
Storage Temperature:
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity:
5 to 95% (non-condensing)
Power Requirements
Input Voltage:
12 to 48 VDC, redundant dual DC power inputs or 48 VDC Power-over-
Ethernet (IEEE 802.3af
compliant)
Connector:
10-pin removable terminal block, 500 V insulation
Power Consumption:
Max. 7.2 W (12V/0.6A to 48V/0.15A), 25°C
Reverse Polarity Protection:
Present
Standards and Certifications
Safety:
UL 60950-1, EN 60950-1
EMC:
EMI: CISPR 22, FCC Part 15B Class B
EMS:
EN 61000-6-2/61000-6-4
IEC 61000-4-2 ESD: Contact 8 kV; Air 15 kV
IEC 61000-4-3 RS: 10 V/m (80 MHz to 1 GHz)
IEC 61000-4-4 EFT: Power 2 kV; Signal 1 kV
IEC 61000-4-5 Surge: Power 2 kV; Signal 1 kV
IEC 61000-4-6 CS: 10 V
IEC 61000-4-8
Note: Please check Moxa’s website for the most up
-to-date certification status.
Warranty
Warranty Period:
5 years
Details:
See www.moxa.com/warranty
www.ipc2u.ru
www.moxa.pro

WAC-1001 Introduction
1-4
ATTENTION
The WAC
-1001 is NOT designed for use by the general public. A well-
trained technician is required to safely
deploy the WAC
-1001.
Functional Design
LED Indicators
The LEDs on the front panel of the WAC-1001 provide a quick and easy means of determining the current
operational status and wireless settings.
The FAULT LED indicates system failures and user-configured events. If the WAC-1001 cannot retrieve an IP
address from a DHCP server, the FAULT LED will blink at one second intervals.
Beeper
The beeper emits two short beeps when the system is ready.
Reset Button
The RESET button is located on the top panel of the WAC-1001. You can reboot the WAC-1001 or reset it to
the factory default settings by pressing the RESET button with a pointed object such as an unfolded paper clip.
•System reboot: Press and release the RESET button
•Reset to factory default: Depress the RESET button for more than 5 seconds until the STATE LED starts
blinking green, and then release.
www.ipc2u.ru
www.moxa.pro

WAC-1001 Introduction
1-5
Relay (Digital Output)
The WAC-1001 has one relay output consisting of the 2 terminal block contacts on the top panel, as shown
below. These relay contacts are used to forward system failures and user-configured events.
The two wires attached to the relay contacts form an open circuit when a user-configured event is triggered. If
a user-configured event does not occur, the relay circuit will remain closed. For safety reasons, the relay circuit
is kept open when the WAC-1001 is not powered up.
Summary of the WAC-1001’s Relay Status
Power Status Event Relay
Off – Open
On Yes Open
No Short
www.ipc2u.ru
www.moxa.pro

2
2. Getting Started
This chapter explains how to install the WAC-1001 for the first time, and quickly set up your wireless network.
The Function Map provides a convenient means of determining which functions you need to use.
The following topics are covered in this chapter:

First-time Installation and Configuration

Function Map
www.ipc2u.ru
www.moxa.pro

WAC-1001 Getting Started
2-2
First-time Installation and Configuration
Before installing the WAC-1001, make sure that all items in the Package Checklist are in the box. You will need
access to a notebook computer or PC equipped with an Ethernet port. The WAC-1001 has a default IP address
that must be used when connecting to the device for the first time.
•Step 1: Select the power source.
The WAC-1001 can be powered by a DC power input or PoE (Power over Ethernet). The WAC-1001 will use
whichever power source you choose.
•Step 2: Connect the WAC-1001 to a notebook or PC.
Since the WAC-1001 supports MDI/MDI-X auto-sensing, you can use either a straight-through cable or
crossover cable to connect the WAC-1001 to a computer. The LED indicator on the WAC-1001’s LAN port
will light up when a connection is established.
•Step 3: Set up the computer’s IP address.
Choose an IP address on the same subnet as the WAC-1001. Since the WAC-1001’s default IP address is
192.168.127.253, and the subnet mask is 255.255.255.0, you should set the IP address of the
computer to 192.168.127.xxx.
NOTE
After you select
Maintenance Load Factory Default and click the Submit button, the WAC-
1001 will be
reset to factory default settings and the IP address will be reset to
192.168.127.253.
•Step 4: Use the web-based manager to configure the WAC-1001
Open your computer’s web browser and type http://192.168.127.253 in the address field to access the
homepage of the web-based Network Manager. Before the homepage opens, you will need to enter the user
name and password as shown in the following figure. For first-time configuration, enter the default user
name and password and then click on the Login button:
NOTE
Default user name and password:
User Name: admin
Password: root
For security reasons, we strongly recommend changing the default password. To do so, select Maintenance

Password, and then follow the on-screen instructions to change the password.
www.ipc2u.ru
www.moxa.pro

WAC-1001 Getting Started
2-3
•Step 5: Set up Roaming domain
The first time you log into the WAC-1001, a warning message will be displayed on your computer’s web
browser to remind you to set the value of the Roaming domain. Click Yes to go to Controller Settings

Basic WAC Settings to set up the Roaming domain . If the Roaming domain is not configured, the
WAC-1001 will not function properly. Note that the AP and clients in the same roaming domain MUST be
configured and grouped in the same subnet.
•Step 6: More settings to better configure the WAC-1001
On the WAC-1001’s web-based UI, there are additional setting options for a more customized configuration.
Refer to the following chapters for more details.
NOTE
After clicking Submit to apply changes, the web page will refresh and (Updated) will appear on the page, and
at the same time a flashing reminder on the upper
-right corner of the web page will be displayed as shown
below:
To activate the changes, click the Restart button, and then the Save and Restart button. It will take about 40
seconds for the WAC
-1001 to complete the reboot procedure.
www.ipc2u.ru
www.moxa.pro

WAC-1001 Getting Started
2-4
Function Map
Main Menu
Overview
Basic Settings
System Info Settings
Network Settings
Time Settings
Controller Settings
Basic WAC Settings
WAC Secure Settings
Advanced Settings
SNMP Agent
Auto Warning Settings
System Log
System Log Event Types
Syslog
Syslog Event Types
Syslog Server Settings
E-mail
E-mail Event Types
E
-mail Server Settings
Relay
Relay Event Types
Trap
Trap Event Types
SNMP Trap Receiver Settings
Status
System Log
Relay Status
DI and Power Status
Managed Device List
LAN Status
Maintenance
Console Settings
Ping
Firmware Upgrade
Config Import Export
Load
Factory Default
Username/Password
Locate Device
Misc. Settings
Save Configuration
Restart
Logout
Quick overview of the WAC-1001’s status
Basic settings for administering the WAC-1001
Essential settings related to set up a wireless access
controller
Advanced features to support additional network
management
Note: These advanced functions are all optional.
Application-oriented device management functions to
set up events, traps, and reactions via relay warning,
e-mail, and SNMP notification
Note: These advanced functions are all optional.
Real-time status information for performance
monitoring and device management functions
Functions for maintaining the WAC-1001, and for
diagnosing the network
On-demand functions to support the web-based
console management operation
www.ipc2u.ru
www.moxa.pro

3
3. Web Console Configureation
In this chapter, we explain all aspects of web-based console configuration. Moxa’s easy-to-use management
functions help you set up your WAC-1001.
The following topics are covered in this chapter:

Web Browser Configuration

Overview

Basic Settings
System Info Settings
Network Settings
Time Settings

Controller Settings
Basic WAC Settings
WLAN Security Settings

Advanced Settings
SNMP Agent

Auto Warning Settings
System Log
Syslog
E-mail
Relay
Trap

Status
System Log
Relay Status
DI and Power Status
Managed Device List
LAN Status

Maintenance
Console Settings
Ping
Firmware Upgrade
Config Import Export
Load Factory Default
Username/Password
Locate Device
Misc. Settings

Save Configuration

Restart

Logout
www.ipc2u.ru
www.moxa.pro

WAC-1001 Web Console Configureation
3-2
Web Browser Configuration
Moxa WAC-1001’s web browser interface provides a convenient way to modify its configuration and access the
built-in monitoring and network administration functions. The recommended web browser is Microsoft®
Internet Explorer 7.0 or 8.0 with JVM (Java Virtual Machine) installed.
NOTE
To use the WAC
-1001’s
management and monitoring functions from a PC host connected to the same LAN as
the WAC
-1001, you must make sure that the PC host and the WAC-
1001 are on the same logical subnet. The
Moxa WAC
-1001’s default IP is 192.168.127.253.
Follow these steps to access the WAC-1001’s web-based console management interface.
1. Open your web browser (e.g., Internet Explorer) and type the WAC-1001’s IP address in the address field.
Press Enter to establish the connection.
2. The Web Console Login page will open. Enter the password (default Username = admin; default Password
= root) and then click Login to continue.
3. You may need to wait a few moments for the web page to download to your computer. Note that the Model
name and IP address of your WAC-1001 are both shown in the title bar of the web page. This information
can be used to help you identify multiple WAC-1001 units.
www.ipc2u.ru
www.moxa.pro

WAC-1001 Web Console Configureation
3-3
4. Use the menu tree on the left side of the window to open the function pages to access each of the
WAC-1001’s functions.
In the following paragraphs, we describe each WAC-1001 management function in detail. A quick overview is
available in this manual in the “Function Map” section of Chapter 2.
NOTE
For security reasons, you will need to log back into the WAC
-1001 after a 5-minute time-out.
www.ipc2u.ru
www.moxa.pro

WAC-1001 Web Console Configureation
3-4
Overview
The Overview page summarizes the WAC-1001’s current status. The information is categorized into several
groups: System info, Device info, and Controller info.
Basic Settings
The Basic Settings group includes the most commonly used settings required by administrators to maintain and
control the WAC-1001.
System Info Settings
The System Info items, especially Device name and Device description, are displayed and included on the
Overview page, in SNMP information, and in alarm emails. Setting System Info items makes it easier to
identify the different WAC-1001 units connected to your network.
www.ipc2u.ru
www.moxa.pro

WAC-1001 Web Console Configureation
3-5
Device name
Setting Description Factory Default
Max. 31 of characters This option is useful for specifying the role or application of
different WAC-1001 units. WAC-1001_<Serial No. of this
WAC-1001>
Device location
Setting Description Factory Default
Max. of 31 characters Specifies the location of different WAC-1001 units. None
Device description
Setting Description Factory Default
Max. of 31 characters Use this space to record a more detailed description of the
WAC-1001 None
Device contact information
Setting Description Factory Default
Max. of 31 characters
Provides information about whom to contact in order to resolve
problems. Use this space to record contact information of the
person responsible for maintaining this WAC-1001.
None
Network Settings
The Network Settings configuration panel allows you to modify the usual TCP/IP network parameters. An
explanation of each configuration item is given below.
IP configuration
Setting Description Factory Default
DHCP The WAC-1001’s IP address will be assigned automatically by
the network’s DHCP server Static
Static Set up the WAC-1001’s IP address manually.
IP address
Setting Description Factory Default
WAC-1001’s IP address
Identifies the WAC-1001 on a TCP/IP network. 192.168.127.253
Subnet mask
Setting Description Factory Default
WAC-1001’s subnet
mask Identifies the type of network to which the WAC-1001 is connected (e.g., 255.255.0.0 for a Class B network, or
255.255.255.0 for a Class C network).
255.255.255.0
Gateway
Setting Description Factory Default
WAC-1001’s default
gateway The IP address of the router that connects the LAN to an outside network. None
www.ipc2u.ru
www.moxa.pro

WAC-1001 Web Console Configureation
3-6
Primary/ Secondary DNS server
Setting Description Factory Default
IP address of the
Primary/Secondary
DNS server
The IP address of the DNS Server used by your network. After
entering the DNS Server’s IP address, you can input the
WAC-1001’s URL (e.g., http://ap11.abc.com) in your browser’s
address field instead of entering the IP address. The Secondary
DNS server will be used if the Primary DNS server fails to
connect.
None
Time Settings
The WAC-1001 has a time calibration function based on information from an NTP server or user specified Date
and Time information. Functions such as Auto warning can add real-time information to the message.
The Current local time shows the WAC-1001’s system time when you open this web page. You can click on
the Set Time button to activate the updated date and time parameters. An “(Updated)” string will appear to
indicate that the change is complete. Local time settings will be immediately activated in the system without
running Save and Restart.
NOTE
The WAC
-1001 has a built-in real time clock (RTC). We strongly recommend that users update the
Local time
for the WAC
-1001 after the initial setup or a long-
term shutdown, especially when the network does not have
an Internet connection for accessing the NTP server or there
is no NTP server on the LAN.
Current local time
Setting Description Factory Default
User adjustable time The date and time parameters allow configuration of the local
time, with immediate activation.
Use 24-hour format: yyyy/mm/dd hh:mm:ss
None
Time protocol
Setting Description Factory Default
SNTP Selects SNTP server functionality for clients SNTP
NTP Selects NTP server functionality for clients
Time zone
Setting Description Factory Default
User selectable time
zone The time zone setting allows
conversion from GMT (Greenwich
Mean Time) to local time. GMT (Greenwich
Mean Time)
www.ipc2u.ru
www.moxa.pro

WAC-1001 Web Console Configureation
3-7
ATTENTION
Because the
current local time will be adjusted automatically as the time zone is being adjusted
, you will
need to configure the
time zone prior to inputting the current local time.
Daylight saving time
Setting Description Factory Default
Enable/ Disable Daylight saving time (also known as DST or summer time)
involves advancing clocks (usually 1 hour) during the summer
time to provide an extra hour of daylight in the afternoon.
Disable
When Daylight saving time is enabled, the following parameters will be shown:
•Starts at: The date that daylight saving time begins.
•Stops at: The date that daylight saving time ends.
•Time offset: Indicates how many hours forward the clock should be advanced.
Time server 1/2
Setting Description Factory Default
IP/Name of Time
Server 1/2 IP or Domain name of the NTP time server. The 2nd NTP server will be used if the 1st NTP server fails to connect. None
Query period
Setting Description Factory Default
Query period time
(1 to 9999 seconds) This parameter determines how often the time is updated from the NTP server. 600 (seconds)
Controller Settings
The Controller Settings group includes the most important settings, which enable administrators to set up the
WAC-1001’s services.
Basic WAC Settings
The Roaming method and the Roaming domain’s information are displayed on the Overview page.
Note: Using the Roaming method requires the input of different parameters. See below for details.
Roaming method: Compare
www.ipc2u.ru
www.moxa.pro