MP F50S User manual

F50S Service Parts and Maintenance
MASTER PNEUMATIC - DETROIT, INC.
6701 -18 Mile Rd. | Sterling Heights, MI 48314 | Phone: [phone] | Fax: [phone] | Email: [e-mail]
JAA 10-10-03
REV 10-03-05
(ECN 4075)
STU-2004
Installation Procedures
Replacement Parts & Kits
BF50S Section View
(Manual Drain)
KEY DESCRIPTION BF50S-2V F50S-2V
1 Head 130-15S-1/4 130-15S-1/4
2 O-Ring, Bowl 406-23V 406-23V
3 Element Kit KA130-27PE5V KA130-27PE5V
4 Metal Bowl with Manual Drain ABF130-22SV ABF130-22SV
5 Manual Drain Kit K60F-11M A130-19V
Not
Shown Plastic Bowl with Manual Drain A10F-130V A10F-130V
THANK YOU!
You have just purchased a quality Filter from Master Pneumatic.
With care in it’s installation and maintenance, you can expect it to have a long and
economical service life. Before you go any further, please take a few
minutes to look over this information, then save it for future reference and
for the useful service information it contains.
1
2
3
INSTALLATION:
Depressurize and lockout air pressure. Install the filter as near as possible to the device it is to serve, following the arrow direction on the filter
head for air flow. Filters should be installed upstream of any regulators, lubricators, or valves in the air line.
ADJUSTMENTS:
Manual Drain: For Metal Bowls: Turn knob (B) clockwise to drain filter. For Plastic bowls: Push drain knob to drain filter.
MAINTENANCE:
To clean or service the unit, depressurize and lockout air pressure. Remove bowl assembly by turning counterclockwise. To remove the element
(#3), insert a screwdriver in the slot located at the bottom of stem (A). Turn stem (A) counterclockwise until it is free of head (#1). Replace with
new element and reassemble to finger tight. Do not clean filter elements, they must be replaced. Sintered bronze elements may be cleaned by
soaking several hours in a suitable solvent, then blowing them out in reverse direction to normal flow with compressed air or steam. For manual
drain models, periodically drain to discharge accumulated liquids.
Plastic bowls may be cleaned with soap and water. Replace plastic bowls with metal if any signs of crazing or cracking are observed.
4
A
B
5
FLOW

B
F50S Service Parts and Maintenance
MASTER PNEUMATIC - DETROIT, INC.
6701 -18 Mile Rd. | Sterling Heights, MI 48314 | Phone: [phone] | Fax: [phone] | Email: [e-mail]
WORKING PRESSURE MAX
PLASTIC BOWL METAL BOWL
150 PSI @ 125°F 200 PSI @ 150°F
(10.3 BAR@ 51.7°C) (13.8 BAR @ 65.5°C)
PREFIX OPTION (REPLACES F)
BF Metal Bowl, Manual Drain
SUFFFIX OPTION
E3 Sintered Bronze Element, 40μm
E4 Sintered Bronze Element, 20μm
E5 Sintered Bronze Element, 5μm
W BSP British (Whitworth) Threads
FILTERING: Standard 5μm Element - Porous Polyethylene.
Dimensional Specifications
General Specifications
KEY BF50S-2V F50S-2V
A 1 5/8
(41 mm)
1 5/8
(41 mm)
B 3/8
(10 mm)
3/8
(10 mm)
C 4 1/4
(108 mm)
3 5/8
(92 mm)
D 1 5/8
(41 mm)
1 5/8
(41 mm)
JAA 10-10-03
REV 10-03-05
(ECN 4075)
STU-2004
A
D
C