MSR ST323 User manual

Wireless Temperature Monitor
Model No.: ST323
Operation Manual
Please Read Carefully Before Using 0434

- 1 -

Thank you for purchasing MSR Wireless Temperature Monitor . Before
you start using this unit, please read this operation manual thoroughly.
Contents
Introduction ............................................................................................... 2
Specications ............................................................................................ 3
Safety Notes .............................................................................................. 4
Components .............................................................................................. 5
Product Descriptions ................................................................................. 6
Icon Idex ................................................................................................... 8
Preparation Before Using .......................................................................... 9
Operation:
Temperature Monitor ....................................................................... 11
Ambient Temperature Indicator ....................................................... 14
Clock ................................................................................................ 15
Responding to Temperature Alarm ........................................................... 16
Important Signal / Light Indicator ............................................................ 17
Battery Replacement ................................................................................. 18
Care and Storage ....................................................................................... 19
Warranty .................................................................................................... 20
1.
2.
3.
- 1 -

【Introduction】
Congratulations! on the purchase of your new MSR Wireless Temperature
Monitor. You may now “Rest Assured” of your loved one’s temperature
either up close or from a distance, even from another room! “Why Wake
your Sleeping Angel up”?
Your new “Wireless Temperature Monitor” is a Technologically advanced
medical device intended for remote monitoring of body temperature for
up to 100 hours of continuous use. It is intended for patients 3 years old to
adult. The device consists of two parts: the transmitter and the receiver.
The transmitter monitors body temperature (via the underarm sensor) then
automatically transmits the measured temperature reading to the remote
receiver.
The following are key features:
• Clinically Accurate: Meets or exceeds ASTM and CE accuracy
standards.
• Accuracy Assurance Function – temperature reading transmits every
15 seconds!
• Fever alarm and fever receding points setting --- Hi, Lo.
• Memory Function - tracks previous readings every 30 minutes.
• Alarm Function – Alarm sounds when temperature deviates from
personalized pre-set parameters.
• Additional Alarm Function – Alarm sounds should sensor become
disconnected.
• Clock Function.
• Room Temperature Function – Scans and reads ambient temperature.
• Backlit for easy night reading when any button on the control panel
is touched.
• FCC approved transmission frequency – 433.92MHz.
• Measures in Centigrade and Fahrenheit.
Trademark and patent Pending
- 2 -
- 3 -

【Specifications】
Size: Transmitter: 2.24 x 1.60 x .72 in.
Receiver: 2.85 x 2.85 x .90 in.
Weight: Transmitter: approx. 36g (1.21 oz)(without battery)
Receiver: approx. 44.2g (1.49 oz) (without battery)
Product Material: Transmitter: ABS
Receiver: ABS
Type of Batteries: Transmitter: 3V x 1 (CR2032)
Receiver: AAA / 1.5V x 2
Life of Batteries: Transmitter: Approx. ＞500hrs
Receiver: Approx. ＞200hrs
Backlight: Backlight will be ON for 5 sec. when you press any button
Effective Distance for Transmission and Reception:
160 feet distance (approx.50M) in an open space. If there are objects in that
space, the transmission distance will be affected.
Range of Temperature Settings: 10.0℃~ 43.0℃(50.0℉~ 109.4℉)
Temperature Accuracy: ±0.1℃/ 0.2℉between 32℃~ 43.0℃(89.6℉~
109.4℉)
±0.5℃/ 1.0℉beyond above range
Storage environment: Transmitter / Receiver
Ambient temperature: -10.0℃~ 60.0℃(14.0℉~
140.0℉)
Humidity: 30% -80% RH
Temperature Measurement Interval: Transmitter measures body
temperature once every 15
seconds.
Transmitting Signal: When transmitter detects body temperatures
exceeding the High-Low range three (3) times in
a row, it transmits a signal to the receiver to sound
an alarm.
Sound of Receiver Alarm: Low: Long BiBiBi
High: Short BiBiBi
Frequency of Transmission: 433.92 MHz
Memory Function: 200 sets
- 2 -
- 3 -

【Safety Notes】
Warning
Before you start using this unit, please read this operation manual
thoroughly for the correct operation procedures.
This device is not waterproof and must never be submersed in any
liquid.
Do not drop or disassemble the unit.
Avoid exposing the thermometer to direct sunlight, high temperature,
moisture or dirt.
If the unit will not be used for a long time, it is recommended that the
battery is removed and stored from the reach of children.
If the unit becomes contaminated, clean it with a damp cloth.
Changes or modications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
The user manual or instruction manual for an intentional or unintentional
radiator shall caution the user that changes or modications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
1.
2.
3.
4.
5.
6.
- 4 -
- 5 -

【Components】
Receiver
Transmitter
Battery for receiver
Sensor patch
Battery for Transmitter
- 4 -
- 5 -

μProduct Descriptionsν
Receiver group:
【Product Descriptions】
Receiver group:
Light Indicator
LCD
Power Key
Selection button
Selection button
Battery for Receiver
Setting key
Setting Key
For Year/Month/Date/Time
- 6 -
- 7 -

Transmitter group:
CR2032
Receiver group:
Power Key
Light indicator
Sensor Band
Battery for Transmitter
Arm Band
Sensor patch
- 6 -
- 7 -

【Icon Idex】
When you see this Icon on the display, press “
＜
” or “
＜
”
button to switch ℃to ℉or ℉to ℃.
When you see this Icon on the display, press “
＜
” or “
＜
”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “
＜
” or
“
＜
” button to set low temperature limit (fever receding
point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “
＜
” or “
＜
” button to select buzzer
on or off.
When you see this Icon on the display, this unit is on
“memory’ function, press “
＜
” or “
＜
” button to clear
memory function.
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode.
When you see this Icon on the display, this unit is on
temperature setting mode.
When you see this Icon on the display, this unit is on
clock setting mode.
μIcon Idex ν
When you see this Icon on the display, press “” or “”
button to switch кto лʳʳлʳʳкˁ
When you see this Icon on the display, press “” or “”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “” or “”
button to set low temperature limit (fever receding point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “” or “” button to select buzzer is
on or off.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode
When you see this Icon on the display, this unit is on
temperature setting mode
When you see this Icon on the display, this unit is on cloc
k
setting mode
When you see this Icon on the display, this unit is on
“memory’ function, press “” or “” button to clea
r
f ti
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode
μIcon Idex ν
When you see this Icon on the display, press “” or “”
button to switch кto лʳʳлʳʳкˁ
When you see this Icon on the display, press “” or “”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “” or “”
button to set low temperature limit (fever receding point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “” or “” button to select buzzer is
on or off.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode
When you see this Icon on the display, this unit is on
temperature setting mode
When you see this Icon on the display, this unit is on cloc
k
setting mode
When you see this Icon on the display, this unit is on
“memory’ function, press “” or “” button to clea
r
f ti
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode
μIcon Idex ν
When you see this Icon on the display, press “” or “”
button to switch кto лʳʳлʳʳкˁ
When you see this Icon on the display, press “” or “”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “” or “”
button to set low temperature limit (fever receding point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “” or “” button to select buzzer is
on or off.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode
When you see this Icon on the display, this unit is on
temperature setting mode
When you see this Icon on the display, this unit is on cloc
k
setting mode
When you see this Icon on the display, this unit is on
“memory’ function, press “” or “” button to clea
r
f ti
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode
μIcon Idex ν
When you see this Icon on the display, press “” or “”
button to switch кto лʳʳлʳʳкˁ
When you see this Icon on the display, press “” or “”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “” or “”
button to set low temperature limit (fever receding point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “” or “” button to select buzzer is
on or off.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode
When you see this Icon on the display, this unit is on
temperature setting mode
When you see this Icon on the display, this unit is on cloc
k
setting mode
When you see this Icon on the display, this unit is on
“memory’ function, press “” or “” button to clea
r
f ti
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode
μIcon Idex ν
When you see this Icon on the display, press “” or “”
button to switch кto лʳʳлʳʳкˁ
When you see this Icon on the display, press “” or “”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “” or “”
button to set low temperature limit (fever receding point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “” or “” button to select buzzer is
on or off.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode
When you see this Icon on the display, this unit is on
temperature setting mode
When you see this Icon on the display, this unit is on cloc
k
setting mode
When you see this Icon on the display, this unit is on
“memory’ function, press “” or “” button to clea
r
f ti
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode
μIcon Idex ν
When you see this Icon on the display, press “” or “”
button to switch кto лʳʳлʳʳкˁ
When you see this Icon on the display, press “” or “”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “” or “”
button to set low temperature limit (fever receding point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “” or “” button to select buzzer is
on or off.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode
When you see this Icon on the display, this unit is on
temperature setting mode
When you see this Icon on the display, this unit is on cloc
k
setting mode
When you see this Icon on the display, this unit is on
“memory’ function, press “” or “” button to clea
r
f ti
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode
μIcon Idex ν
When you see this Icon on the display, press “” or “”
button to switch кto лʳʳлʳʳкˁ
When you see this Icon on the display, press “” or “”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “” or “”
button to set low temperature limit (fever receding point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “” or “” button to select buzzer is
on or off.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode
When you see this Icon on the display, this unit is on
temperature setting mode
When you see this Icon on the display, this unit is on cloc
k
setting mode
When you see this Icon on the display, this unit is on
“memory’ function, press “” or “” button to clea
r
f ti
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode
μIcon Idex ν
When you see this Icon on the display, press “” or “”
button to switch кto лʳʳлʳʳкˁ
When you see this Icon on the display, press “” or “”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “” or “”
button to set low temperature limit (fever receding point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “” or “” button to select buzzer is
on or off.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode
When you see this Icon on the display, this unit is on
temperature setting mode
When you see this Icon on the display, this unit is on cloc
k
setting mode
When you see this Icon on the display, this unit is on
“memory’ function, press “” or “” button to clea
r
f ti
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode
μIcon Idex ν
When you see this Icon on the display, press “” or “”
button to switch кto лʳʳлʳʳкˁ
When you see this Icon on the display, press “” or “”
button to set high temperature (fever alarm point).
When you see this Icon on the display, press “” or “”
button to set low temperature limit (fever receding point).
When you see this Icon on the display, this unit is on
“alarm’ status, press “” or “” button to select buzzer is
on or off.
When you see this Icon on the display, this unit is on
“ambient temperature monitor’ mode
When you see this Icon on the display, this unit is on
temperature setting mode
When you see this Icon on the display, this unit is on cloc
k
setting mode
When you see this Icon on the display, this unit is on
“memory’ function, press “” or “” button to clea
r
f ti
When you see this Icon on the display, this unit is on
“wireless temperature monitor’ mode
- 8 -
- 9 -

μPreparation Before Usingν
Step one: Install battery
CR2032
Step two:
One CR2032 (3 volt) battery
zUse a coin or a screw driver to open the battery
cover by turning counter-clockwise.
zInsert one battery in the battery compartment.
The positive (+) side should be faced up.
zTurn clockwise to close the battery cover.
Two AAA (1.5V) batteries
zRemove the battery compartment cover.
zInsert two batteries in the battery compartment
as indicated.
zPut the battery cover back on.
Press the button of the sensor patch to the sensor band
μPreparation Before Usingν
Step one: Install battery
CR2032
Step two:
One CR2032 (3 volt) battery
zUse a coin or a screw driver to open the battery
cover by turning counter-clockwise.
zInsert one battery in the battery compartment.
The positive (+) side should be faced up.
zTurn clockwise to close the battery cover.
Two AAA (1.5V) batteries
zRemove the battery compartment cover.
zInsert two batteries in the battery compartment
as indicated.
zPut the battery cover back on.
Press the button of the sensor patch to the sensor band
μPreparation Before Usingν
Step one: Install battery
CR2032
Step two:
One CR2032 (3 volt) battery
zUse a coin or a screw driver to open the battery
cover by turning counter-clockwise.
zInsert one battery in the battery compartment.
The positive (+) side should be faced up.
zTurn clockwise to close the battery cover.
Two AAA (1.5V) batteries
zRemove the battery compartment cover.
zInsert two batteries in the battery compartment
as indicated.
zPut the battery cover back on.
Press the button of the sensor patch to the sensor band
【Preparation Before Using】
Step one: Install battery
One CR2032 (3 volt) battery
●Use a coin or a screw driver to open
the battery cover by turning counter-
clockwise.
●Insert one battery in the battery
compartment. The positive (+) side
should be faced up.
●Turn clockwise to close the battery
cover.
Two AAA (1.5V) batteries
●Remove the battery compartment cover.
●Insert two batteries in the battery
compartment as indicated.
●Put the battery cover back on.
Step two:
Press the button of the sensor patch to the sensor band
- 8 -
- 9 -

Step three: Fasten the arm band
Step three: Fasten the arm band
Remark:
** The sensor patch is one-time use, when you use up the attached 3 sensor patches,
you can buy it from your nearby distributor.
** If oil or similar substance gets on the surface of the adhesive patch,
it will not stick as well and will not last as long.
Note: The receiver should be kept with the caretaker remotely.
Step 1
Put the armband on the upper arm and
adjust armband to the proper tightness.
Step 2
Peel off the cover from the sensor
p
Step three: Fasten the arm band
Remark:
** The sensor patch is one-time use, when you use up the attached 3 sensor patches,
you can buy it from your nearby distributor.
** If oil or similar substance gets on the surface of the adhesive patch,
it will not stick as well and will not last as long.
Note: The receiver should be kept with the caretaker remotely.
Step 1
Put the armband on the upper arm and
adjust armband to the proper tightness.
Step 2
Peel off the cover from the sensor
p
Step 1
Put the armband on the upper
arm and adjust armband to the
proper tightness
Step 2
Peel off the cover from the
sensor patch.
Step 3
Afx the sensor patch under the
armpit
Remark:
** The sensor patch is one-time use, when you use up the attached 3
sensor patches, you can buy it from your nearby distributor.
** If oil or similar substance gets on the surface of the adhesive patch,
it will not stick as well and will not last as long.
Note: The receiver should be kept with the caretaker remotely.
- 10 -
- 11 -

【Operation】
Temperature Monitor
＊To activate the I/O button
Press the
μOperationν
Clock
The Receiver can be used as clock alone.
Ϡʳ To set year/month/ date / time
Press to activate this unit, click the “set” button continuously until the icon is
shown on the left side of the display , press “” or “” to selelct icon
is shown on the left side of the display .
When the clock signal on the display, press ”set” button (on the back of receiver)
twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in order, do not
forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock display.
button for approximately 3 seconds to activate this device.
The LCD will show all segments temporarily.
＊To switch between ℉/℃
When the device is activated, click “set” button until “C or F” appears
on the display, Press “
＜
” or “
＜
” for switching between ℉and ℃, then
press “set ” button once again.
＊To set “Hi ”(fever alarm point) temperature limit:
Following ℉/℃setting, “Hi” will appear on the display, press “
＜
” or
“
＜
” to set high temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1℃(or 0.1℉)
μOperationν
Temperature Monitor
Ϡʳ To activate the I/O button
Press the button for approximately 3 seconds to activate this device.
The LCD will show all segments temporarily.
Ϡʳ To switch between /л к
When the device is activated, click “set” button until “C” appears on the display, Press
“” or “” for switching between and , then press “set” once again.л к
Ϡʳ To set “Hi ”(fever alarm point) temperature limit:
Following / setting,л к “Hi” will appear on the display, press “” or “” to set high
temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к(or 0.1л)
μOperationν
Temperature Monitor
Ϡʳ To activate the I/O button
Press the button for approximately 3 seconds to activate this device.
The LCD will show all segments temporarily.
Ϡʳ To switch between /л к
When the device is activated, click “set” button until “C” appears on the display, Press
“” or “” for switching between and , then press “set” once again.л к
Ϡʳ To set “Hi ”(fever alarm point) temperature limit:
Following / setting,л к “Hi” will appear on the display, press “” or “” to set high
temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к(or 0.1л)
μOperationν
Temperature Monitor
Ϡʳ To activate the I/O button
Press the button for approximately 3 seconds to activate this device.
The LCD will show all segments temporarily.
Ϡʳ To switch between /л к
When the device is activated, click “set” button until “C” appears on the display, Press
“” or “” for switching between and , then press “set” once again.л к
Ϡʳ To set “Hi ”(fever alarm point) temperature limit:
Following / setting,л к “Hi” will appear on the display, press “” or “” to set high
temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к(or 0.1л)
μOperationν
Temperature Monitor
Ϡʳ To activate the I/O button
Press the button for approximately 3 seconds to activate this device.
The LCD will show all segments temporarily.
Ϡʳ To switch between /л к
When the device is activated, click “set” button until “C” appears on the display, Press
“” or “” for switching between and , then press “set” once again.л к
Ϡʳ To set “Hi ”(fever alarm point) temperature limit:
Following / setting,л к “Hi” will appear on the display, press “” or “” to set high
temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к(or 0.1л)
Receiver Transmitter
On/Off button
Selection Button Set button
On/Off button
Sensor patch
- 10 -
- 11 -

＊To set “Lo (fever receding point)” temperature limit:
Following “Hi” temperature setting, “Lo” will appear on the display,
press “
＜
” or “
＜
” to set low temperature then press “set” button once
again.
(Temperature setting will change in increments of 0.1℃(or 0.1℉)
Pre-set temperature for Hi and Lo:
＊To set Mute mode
The default is in sound mode. To use mute mode, when icon
is on the display, press “
＜
” or “
＜
” to see below icon on the display and
press “set” button once again.
＊To clear memory
The default is in memory mode. To clear memory, when icon
is on the display, press “
＜
” or “
＜
” to see below icon on the display and
press “set” button once again.
＊To set temperature monitor mode
Following memory mode setting, you will see “tr “ on the display,
press “set” button twice to begin the temperature monitor.
At the same time, make sure the sensor patch is under the armpit of the
patient.
**” tr” stands for transmitting, under this mode, you can monitor
temperature.
Ϡʳ To set “Lo (fever receding point)” temperature limit:
Following “Hi” temperature setting, “Lo” will appear on the display,
press “” or “” to set low temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к (or 0.1л)
Pre-set temperature for Hi and Lo:
Ϡʳ To set Mute mode
The default is in sound mode. To use mute mode, when “On +speaker icon” is on the
display, press “” or “” and press “set” button once again.
Ϡʳ To clear memory
The default is in memory mode. To clear memory, when is on the display,
press “” or “” and press “set” once again.
Ϡʳ To set temperature monitor mode
Following memory mode setting, you will see “tr “ on the display,
press “set” button twice to begin the temperature monitor.
At the same time, make sure the sensor patch is under the armpit of the patient.
**” tr” stands for transmitting, under this mode, you can monitor temperature.
Ϡʳ To set “Lo (fever receding point)” temperature limit:
Following “Hi” temperature setting, “Lo” will appear on the display,
press “” or “” to set low temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к (or 0.1л)
Pre-set temperature for Hi and Lo:
Ϡʳ To set Mute mode
The default is in sound mode. To use mute mode, when “On +speaker icon” is on the
display, press “” or “” and press “set” button once again.
Ϡʳ To clear memory
The default is in memory mode. To clear memory, when is on the display,
press “” or “” and press “set” once again.
Ϡʳ To set temperature monitor mode
Following memory mode setting, you will see “tr “ on the display,
press “set” button twice to begin the temperature monitor.
At the same time, make sure the sensor patch is under the armpit of the patient.
**” tr” stands for transmitting, under this mode, you can monitor temperature.
Ϡʳ To set “Lo (fever receding point)” temperature limit:
Following “Hi” temperature setting, “Lo” will appear on the display,
press “” or “” to set low temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к (or 0.1л)
Pre-set temperature for Hi and Lo:
Ϡʳ To set Mute mode
The default is in sound mode. To use mute mode, when “On +speaker icon” is on the
display, press “” or “” and press “set” button once again.
Ϡʳ To clear memory
The default is in memory mode. To clear memory, when is on the display,
press “” or “” and press “set” once again.
Ϡʳ To set temperature monitor mode
Following memory mode setting, you will see “tr “ on the display,
press “set” button twice to begin the temperature monitor.
At the same time, make sure the sensor patch is under the armpit of the patient.
**” tr” stands for transmitting, under this mode, you can monitor temperature.
Ϡʳ To set “Lo (fever receding point)” temperature limit:
Following “Hi” temperature setting, “Lo” will appear on the display,
press “” or “” to set low temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к (or 0.1л)
Pre-set temperature for Hi and Lo:
Ϡʳ To set Mute mode
The default is in sound mode. To use mute mode, when “On +speaker icon” is on the
display, press “” or “” and press “set” button once again.
Ϡʳ To clear memory
The default is in memory mode. To clear memory, when is on the display,
press “” or “” and press “set” once again.
Ϡʳ To set temperature monitor mode
Following memory mode setting, you will see “tr “ on the display,
press “set” button twice to begin the temperature monitor.
At the same time, make sure the sensor patch is under the armpit of the patient.
**” tr” stands for transmitting, under this mode, you can monitor temperature.
Ϡʳ To set “Lo (fever receding point)” temperature limit:
Following “Hi” temperature setting, “Lo” will appear on the display,
press “” or “” to set low temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к (or 0.1л)
Pre-set temperature for Hi and Lo:
Ϡʳ To set Mute mode
The default is in sound mode. To use mute mode, when “On +speaker icon” is on the
display, press “” or “” and press “set” button once again.
Ϡʳ To clear memory
The default is in memory mode. To clear memory, when is on the display,
press “” or “” and press “set” once again.
Ϡʳ To set temperature monitor mode
Following memory mode setting, you will see “tr “ on the display,
press “set” button twice to begin the temperature monitor.
At the same time, make sure the sensor patch is under the armpit of the patient.
**” tr” stands for transmitting, under this mode, you can monitor temperature.
Ϡʳ To set “Lo (fever receding point)” temperature limit:
Following “Hi” temperature setting, “Lo” will appear on the display,
press “” or “” to set low temperature then press “set” button once again.
(Temperature setting will change in increments of 0.1к (or 0.1л)
Pre-set temperature for Hi and Lo:
Ϡʳ To set Mute mode
The default is in sound mode. To use mute mode, when “On +speaker icon” is on the
display, press “” or “” and press “set” button once again.
Ϡʳ To clear memory
The default is in memory mode. To clear memory, when is on the display,
press “” or “” and press “set” once again.
Ϡʳ To set temperature monitor mode
Following memory mode setting, you will see “tr “ on the display,
press “set” button twice to begin the temperature monitor.
At the same time, make sure the sensor patch is under the armpit of the patient.
**” tr” stands for transmitting, under this mode, you can monitor temperature.
- 12 -
- 13 -

＊Memory Retrieval
In temperature monitor mode, press “
＜
” or “
＜
” to retrieve the
temperature and press the “set” button to retrieve the date / time.
Continue the same procedure to retrieve more sets of data from previous
monitor.
Remark: If the thermometer measures the temperature to be over the “Hi”
temperature or below the “Lo” temperature you have set, the
receiver will sound continuously (bi-bi-bi) and indicator light
ashes red.
Ϡʳ Memory Retrieval
In temperature monitor mode, press “” or “” to retrieve the temperature and press the
“set” button to retrieve the date / time.
Continue the same procedure to retrieve more sets of data from previous monitor.
Remark: 1). If the thermometer measures the temperature to be over the “Hi” temperature or
below the “Lo” temperature you have set, the receiver will sound continuously
(bi-bi-bi) and indicator light flashes red.
2). In Temperature monitor mode, press “” or “” and “set” button to review last
or next memory.
- 12 -
- 13 -

μOperation ν
Ambient Temperature Indicator
Ambient Temperature Measurement
Press the button to activate this unit, click “set” button continuously to see
on the display. Press ““” or “” when “rE” as below picture is on the
display, press ”set” button twice to begin for ambient temperature measurement.
Remark: “rE” stands for “Receiver”
【Operation】
Ambient Temperature Indicator
Ambient Temperature Measurement
Press the
μOperationν
Clock
The Receiver can be used as clock alone.
Ϡʳ To set year/month/ date / time
Press to activate this unit, click the “set” button continuously until the icon is
shown on the left side of the display , press “” or “” to selelct icon
is shown on the left side of the display .
When the clock signal on the display, press ”set” button (on the back of receiver)
twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in order, do not
forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock display.
button to activate this unit, click “set” button continuously to
see
μOperation ν
Ambient Temperature Indicator
Ambient Temperature Measurement
Press the button to activate this unit, click “set” button continuously to see
on the display. Press ““” or “” when “rE” as below picture is on the
display, press ”set” button twice to begin for ambient temperature measurement.
Remark: “rE” stands for “Receiver”
on the display. Press “
＜
” or “
＜
” when “rE” as below
picture is on the display, press ”set” button twice to begin for ambient
temperature measurement.
Remark: “rE” stands for “Receiver”
- 14 -
- 15 -

【Operation】
Clock
The Receiver can be used as clock alone.
＊To set year/month/ date / time
Press
μOperationν
Clock
The Receiver can be used as clock alone.
Ϡʳ To set year/month/ date / time
Press to activate this unit, click the “set” button continuously until the icon is
shown on the left side of the display , press “” or “” to selelct icon
is shown on the left side of the display .
When the clock signal on the display, press ”set” button (on the back of receiver)
twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in order, do not
forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock display.
to activate this unit, click the “set” button continuously until the
μOperationν
Clock
The Receiver can be used as clock alone.
Ϡʳ To set year/month/ date / time
Press to activate this unit, click the “set” button continuously until the icon is
shown on the left side of the display , press “” or “” to selelct icon
is shown on the left side of the display .
When the clock signal on the display, press ”set” button (on the back of receiver)
twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in order, do not
forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock display.
icon (
μOperationν
Clock
The Receiver can be used as clock alone.
Ϡʳ To set year/month/ date / time
Press to activate this unit, click the “set” button continuously until the icon is
shown on the left side of the display , press “” or “” to selelct icon
is shown on the left side of the display .
When the clock signal on the display, press ”set” button (on the back of receiver)
twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in order, do not
forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock display.
)is shown on the left side of the display, press “
＜
” or
“
＜
” to selelct
μOperationν
Clock
The Receiver can be used as clock alone.
Ϡʳ To set year/month/ date / time
Press to activate this unit, click the “set” button continuously until the icon is
shown on the left side of the display , press “” or “” to selelct icon
is shown on the left side of the display .
When the clock signal on the display, press ”set” button (on the back of receiver)
twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in order, do not
forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock display.
icon is (
μOperationν
Clock
The Receiver can be used as clock alone.
Ϡʳ To set year/month/ date / time
Press to activate this unit, click the “set” button continuously until the icon is
shown on the left side of the display , press “” or “” to selelct icon
is shown on the left side of the display .
When the clock signal on the display, press ”set” button (on the back of receiver)
twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in order, do not
forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock display.
) shown on the left side of the display.
When the clock signal on the display, press ”set” button (on the back of
receiver) twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in
order, do not forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock
display.
μOperationν
Clock
The Receiver can be used as clock alone.
Ϡʳ To set year/month/ date / time
Press to activate this unit, click the “set” button continuously until the icon is
shown on the left side of the display , press “” or “” to selelct icon
is shown on the left side of the display .
When the clock signal on the display, press ”set” button (on the back of receiver)
twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in order, do not
forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock display.
μOperationν
Clock
The Receiver can be used as clock alone.
Ϡʳ To set year/month/ date / time
Press to activate this unit, click the “set” button continuously until the icon is
shown on the left side of the display , press “” or “” to selelct icon
is shown on the left side of the display .
When the clock signal on the display, press ”set” button (on the back of receiver)
twice, you can set year / month/ date time in turn.
Remark: 1). “Time” button is to adjust year / date / time.
Whenever you finish year setting or date or time setting in order, do not
forget to press “set” button once.
2). After setting, press on/off button twice, it will be in table clock display.
On/Off button “Set” button Time button
(adjust year/ date/ time)
“Set” button
- 14 -
- 15 -

【Responding to Temperature Alarm】
After the receiver sounds the alarm, it will continue to ring unless the
receiver is switched off manually (alarm can be temporarily turned off by
pressing any key on the receiver )
Caution: It is dangerous to automatically switch off the receiver alarm
without nding out why it sounded in the rst place. Doing so makes the
caretaker forget the importance of taking immediate action for the patient.
The correct procedure is:
1. Hear the receiver alarm sounds.
2. Turn off the “alarm” by pressing any button on the receiver.
3. Go to the patient immediately.
4. Provide proper care to the patient.
5. Reset or turn off the receiver if necessary.
Alarm Display on LCD Status
BiBi- BiBi– BiBi NorF and weak antenna
signal
When the receiver
doesn’t receive signal
from transmitter
Bi - Bi
μResponding to Temperature Alarmν
After the receiver sounds the alarm, it will continue to ring unless the receiver is switched off
manually (alarm can be temporarily turned off by pressing any key on the receiver )
Caution: It is dangerous to automatically switch off the receiver alarm without finding
out why it sounded in the first place. Doing so makes the caretaker forget the
importance of taking immediate action for the patient. The correct procedure is:
1. Hear the receiver alarm sounds.
2. Turn off the “alarm” by pressing any button on the receiver
3. Go to the patient immediately.
4. Provide proper care to the patient.
5. Reset or turn off the receiver if necessary
Alarm Display on LCD Status
BiBi- BiBi– BiBi NorF and weak antenna
signal
When the receiver doesn’t
receive signal from
transmitter
Bi - Bi
Short circuit of Sensor or
sensor patch disconnect from
Sensor band .
Sensor patch disconnect from
the armpit of patient
Short Bi-Bi-Bi Temperature is higher than the
fever alarm point (Hi) you set
Long Bi-Bi-Bi Temperature is lower than the
fever receding point (Lo) you
set
μResponding to Temperature Alarmν
After the receiver sounds the alarm, it will continue to ring unless the receiver is switched off
manually (alarm can be temporarily turned off by pressing any key on the receiver )
Caution: It is dangerous to automatically switch off the receiver alarm without finding
out why it sounded in the first place. Doing so makes the caretaker forget the
importance of taking immediate action for the patient. The correct procedure is:
1. Hear the receiver alarm sounds.
2. Turn off the “alarm” by pressing any button on the receiver
3. Go to the patient immediately.
4. Provide proper care to the patient.
5. Reset or turn off the receiver if necessary
Alarm Display on LCD Status
BiBi- BiBi– BiBi NorF and weak antenna
signal
When the receiver doesn’t
receive signal from
transmitter
Bi - Bi
Short circuit of Sensor or
sensor patch disconnect from
Sensor band .
Sensor patch disconnect from
the armpit of patient
Short Bi-Bi-Bi Temperature is higher than the
fever alarm point (Hi) you set
Long Bi-Bi-Bi Temperature is lower than the
fever receding point (Lo) you
set
Short circuit of sensor
or sensor patch dis-
connect from sensor
band.
Sensor patch disconnect
from the armpit of
patient
Short Bi-Bi-Bi
Temperature is higher
than the fever alarm
point (Hi) you set
Long Bi-Bi-Bi
Temperature is lower
than the fever receding
point (Lo) you set
- 16 -
- 17 -

【Important Signal】
Indicates low battery on the transmitter when the LCD shows
a ashing battery signal.
Indicates low battery on the receiver when the LCD shows a
battery signal.
If the reading of the patient is less than 32.0℃(89.6℉) , the
LCD will display “ Lo”.
If the reading of the patient is greater than 43.0℃(109.4℉) ,
the LCD will display “H ”.
Short circuit of Sensor or sensor patch disconnect from sensor
band.
Sensor patch disconnect from the armpit of patient.
【Light Indicator】
Light Status
Green
●Power On
●Receiving signal
Red
●Alarm
●Short circuit of Sensor or sensor patch disconnect from
sensor band
●Sensor patch disconnect from the armpit of patient
Orange ●Low battery
Remark: The light indicator is off in clock mode.
μImportant Signalν
Indicates low battery on the transmitter when the LCD shows a flashing
battery signal
Indicates low battery on the receiver when the LCD shows a battery signal
If the reading of the patient is less than 32.0кʳʻˋˌˁˉлʼʳʿʳthe LCD will
isplay “ Lo”.
If the reading of the patient is greater than 43.0к(109.4л) , the LCD will
display “H ”.
Short circuit of Sensor or sensor patch disconnect from sensor band.
Sensor patch disconnect from the armpit of patient
μLight Indicatorν
Light Status
zPower On
Green zReceiving signal
zAlarm
zShort circuit of Sensor or sensor patch disconnect from sensor
band
Red
zSensor patch disconnect from the armpit of patient
Orange zLow battery
Remark: The light indicator is off in clock mode.
- 16 -
- 17 -

【Battery Replacement】
Transmitter:
When a battery sign appears in the transmitter LCD display, it means the
battery is low and should be replaced as described below:
Removed the battery compartment cover from the bottom of
the transmitter.
Take out the battery
Insert new battery securely in place, with words facing up.
Put the battery compartment cover back on.
Important Note: Clock mode needs to be reset after batteries replaced.
Receiver:
When Red LED light of receiver blinks, it indicates low battery condition.
To replace batteries, follow the procedures described below in order to
avoid causing damage.
Remove the battery compartment cover. Take out the
batteries.
Insert new batteries.
Put the battery compartment cover back on
μBattery Replacementν
Transmitter:
When a battery sign appears in the transmitter LCD display, it means the battery is low and
should be replaced as described below:
Removed the battery compartment cover from the bottom of the
transmitter.
Take out the battery
Insert new battery securely in place, with words facing up.
Put the battery compartment cover back on.
Important Note: ˖˿˶˾ʳ˷˸ʳ˸˸˷ʳʳ˵˸ reset after batteries replaced.
Receiver:
When Red LED light of receiver blinks, it indicates low battery condition. To replace
batteries, follow the procedures described below in order to avoid causing damage.
Remove the battery compartment cover. Take out the batteries.
Insert new batteries.
Put the battery compartment cover back on
μBattery Replacementν
Transmitter:
When a battery sign appears in the transmitter LCD display, it means the battery is low and
should be replaced as described below:
Removed the battery compartment cover from the bottom of the
transmitter.
Take out the battery
Insert new battery securely in place, with words facing up.
Put the battery compartment cover back on.
Important Note: ˖˿˶˾ʳ˷˸ʳ˸˸˷ʳʳ˵˸ reset after batteries replaced.
Receiver:
When Red LED light of receiver blinks, it indicates low battery condition. To replace
batteries, follow the procedures described below in order to avoid causing damage.
Remove the battery compartment cover. Take out the batteries.
Insert new batteries.
Put the battery compartment cover back on
- 18 -
- 19 -