MST MS-01D RTR/S User manual

[ www.rc-mst.com ]
[ facebook.com/MST.tw ]
※Specification are subject to change without notice.
1 / 10 S CALE R C 4 W D HIGH PERFORMAN C E DRI F T CAR
MS-01D RTR/S
ON ROAD USE ONLY
FULL BALL BEARINGS
RTR/SRTR/S
1 / 10 DRIFT CHASSIS
Wheelbase : Standard 257mm (adjustable)
Width : Standard 186mm (adjustable)
Gear ratio : 2.0 ( 36T/18T )
CS ratio : 1.54 ( 40T/13T )
Caster : 4, 7, 10, 14 degrees variableness
Camber : 0 to -12 degrees
Front : Alum. one way
Rear : Spool unit
SPECIFICATION

2MS-01D RTR
/ S
46mm
Appreciate for your choice of MST MS-01D RTR! You will be impressed with its performance and beauty.
Please prepare additional parts as car battery, transmitter battery, and charger.
Please follow the process for assemble and setting of parts package.
If you have doubt or need assistance, please contact the purchased shop or hobby shop for help, many thanks!
首先感謝你購入 MST MS-01D RTR 這項產品，您將擁有一部兼具性能與美型的甩尾車。
在首次操作前，有以下幾項須要另行購置的物件；車用電池、遙控器用電池、充電器。
備妥上述物件後，請進行零件包安裝與設定。
如需其他協助，請向原購買店家，或遙控模型店詢問！謝謝！
Switch off transmitter & ESC.
After attaching servo saver,
Attach fittings.
Steering wheel in neutral.
Switch on the ESC.
Trims the transmitter in neutral.
Switch on the transmitter.
Connector ESC and battery.
Loosen receiver antenna.
Install transmitter batteries.
將遙控器與電子變速器關閉
請在安裝伺服緩衝器之後,
安裝零件包
方向轉盤至中立點
打開電子變速器電源
調整遙控器各微調器至中立點
打開遙控器電源
聯結車用電池與電子變速器
鬆開接收機天線
安裝遙控器電池
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1 / 10 DRIFT CHASSIS
PLEASE FOLLOW BELOW
OPERATIONS BEFORE ASSEMBLING
THE PARTS PACKAGE.
請於安裝零件包之前,執行以下操作
※
請依圖標示之長度安裝,並注意拉桿頭方向。
Please assemble the length as showed, and notice the adjust direction.
※
遙控器&接收機功能說明請參閱詳細說明書。
Please refer to instruction of
transmitter & receiver performance.
※
電子變速器功能說明請參閱詳細說明書。
Please refer to instruction of
ESC performance.
1:1
STEP 1
STEP 2
FACTORY ELECTRONIC SETTING
原廠電裝配線圖
STEERING ROD ASSEMBLY
轉向伺服拉桿組裝
CAR Brushed ESC Manual
1. 遙控器電池安裝
請依照箭頭方向打開電池盒蓋，安裝4顆三號 (A A) 電池於遙控器，
關上電池盒蓋，開啟電源開關，確認遙控器指示燈是否亮 起，若未
亮起，請檢 查電池極性是否安裝正確、電力是否充分。
2. 遙控器指示燈
遙控器開機，LED指示燈恆 亮，代表遙控器電源電力足夠，若 LED
指示燈為 綠色閃爍 還有持續不 斷的短 音聲響，代表遙控器電源電
力不足夠，請更換電池。
3. 使用無線頻帶
頻率是 2.4GHz 頻帶，出廠預設一般模式 (G eneral mode)，亦可切
換至法國模式 (France m ode)。
1. 開機顯示：
遙控器開 機後，蜂鳴器會發出嗶!嗶!兩 聲， 同 時若遙控 器指示
燈有短暫閃 爍為法國模 式；遙控器 指示燈若 無短暫閃 爍為一般
模式。
2. 切換頻帶操作方式：
①進入切換模式：按著(ST Revers e)鍵與(TH Rever se)鍵，開
啟遙控器電源，聽到5短音的聲響後，代表已進入切換模式。
②切換方式：按(TH Revers e)鍵在一般、法國模式間切換。
③頻帶顯示方式：若切換到一般模式，指示 燈會恆亮；若切換到
法國模式，指示 燈為閃爍。
④儲存頻 帶模 式：選定頻帶 模式後，請等2秒鐘，讓遙 控器儲
存頻帶模 式的設定值，接著請關閉遙 控器電 源再開啟遙 控器
電源。
⑤接收器重新聯結：請與接收器重新聯結 (B inding)。
4. 接收機解說
REV TRIM/EPA
Fwd/+
Rev/-
L/- R/+
TH ST
POWER
方向盤
天線
方向正逆轉
油門正逆轉
開關
電池盒
油門前進微調(+)
油門動量微調(+)
油門後退微調(-)
油門動量微調(-)
方向盤大小動作調整
LED指示燈
第3動
油門板機
方向微調(+)
方向動量微調(+)
方向微調(L)
方向動量微調(L)
天線
對頻按鈕
電源阜
LED指示燈
油門伺服機阜
第3動伺服機阜
方向伺服機阜
2.4G / 3CH RADIO CONTROL SYSTEM2.4G / 3CH RADIO CONTROL SYSTEM
3×60mm Thread shaft
4.8mm Adjust
Receiver
Steering servo
ESC
ESC Switch
540 Motor
Battery (not included)
電池 ( )

3MS-01D RTR
/ S
自攻螺絲 (RTR 預設件)
2.6×10mm Taping screw (RTR default)
墊片
3×8×0.5 Spacer
STEP 3
STEP 4
STEP 5
連接電池!
Connect to battery!
電池O環(S)
Battery O-ring (S)
RTR 預設件
25T FUTABA
/ SAVOXRTR default
球頭
4.8×4.5mm Ball connector
請於調整伺服中立點後,依圖示安裝緩衝組。
Attach as shown with servo in neutral.
※
電池的安裝方式會因為廠牌規格而有些微差
異，電池的使用方式與保存方式，也會因電
池的種類而有所不同。
The assembly and conservation
method may be different by
specification of battery.
※
建議安裝長40×寬48×高125.4mm尺寸以內
的電池。
Recommened battery measurement
L140×W48×H125.4mm (not exceed)
※
KO / SANWA FUTABA/ SAVOX
挑選合適的零件安裝。
Match part with servo.
※
23T 25T
SERVO SAVER ASSEMBLY
伺服緩衝組裝
ATTACHING BATTERY
電池安裝
ATTACHING STEERING ROD & SERVO HORN
伺服拉桿&伺服舵片安裝
安裝設定完成後，請於安全場所使用本產品!
使用前請先開啟遙控器電源後再開啟車體電源!
使用後請反向操作關閉!
Please play in safe place after all setting finish.
Before playing, please switch on transmitter then on the car.
Please switch off reversely.
※
90

4
210007
310002
210003
210006
210010
110002
110029
210002
110019
110002
110016
210002
210002
110005
130005
210002
414228
110035 110003
110001
310010
148026
120002
210010
601001
120002
110012
210003
310016
210008
120001
110004
210145R
110003
110001
110012
210003
210009
210009
210003
110014
310001
210014
110011
110001
210014
210014
210283
110001
110002
210183
310043
210009
120001
310042B
210111
110003
110001
210013
110019
210010
310009
110001
210111
210010
210020
210111
110006
110019
110002
110048
210032
210007
601003
130006
600002
310001
110025
110026

5MS-01D RTR
/ S
210006
110008
210007
120002
210016
210016
210002
110029
130007
210012
130003
414486
210004-1
210004-1
210004-1
110018
110003
210004-1
210020
120001
210009
310006
110017
310007
210057
210005
210005
210005
210144-2
310004
130002
310008
130032
110013
210005
210057
130001
210005
210002
110019
110010
210002 210003
110061
210010
110002
210010
210007
110023
110024
210003
110012
210006
210016
310001
120002
110017
210043
110015
210006
110009
210007
110008
210007
210007
210007
210007
210007 110009 310016
310001
110015
210043
110017
210003
110003
210145R
110012
110004
210008
120002
120001
210006 210003
110009
210007
110012
110005
130006 110004
210012
601002
210001
110014
210003
210009
210161
210006
110032
210009
210003
110012
110002
210284

6MS-01D RTR
/ S
PARTS 不使用
Not Used
M3×6 半圓頭螺絲 ×14
Screw
110001
M3×8 半圓頭螺絲 ×18
Screw
110002
M2.5×6 半圓頭螺絲 ×14
Screw
110003
M2.5×14 半圓頭螺絲 ×2
Screw
110010
2.6×10 自攻半圓頭螺絲 ×1
Screw
110025
M2×4 半圓頭螺絲 ×6
Screw
110004
M3×10 半圓頭螺絲 ×1
Screw
110026
2×11.8 插銷 ×6
Shaft
110019
2×13.8 插銷 ×1
Shaft
110018
2×9.8 插銷 ×8
Shaft
110017
M3×8 沉頭螺絲 ×24
Screw
110005
M3×6 沉頭螺絲 ×2
Screw
110024
M3×6 CAP螺絲 ×2
Screw
110011
M3×25 止付螺絲 ×4
Screw
110008
M3×16 止付螺絲 ×2
Screw
110023
M3×13 扁頭螺絲 ×8
Screw
110014
M4 突緣螺帽 ×4
Nut
110015
E2.0 E形扣 ×8
E-clip
110013
R6 R形扣 ×6
R-clip
110016
M3×20 止付螺絲 ×6
Screw
110009
M3×11 扁頭螺絲 ×20
Screw
110012
M3×12 半圓頭螺絲 ×3
Screw
110029
電池O環 (S) ×2
Battery O-ring (S)
130003
天線管 ×1
Antenna pipe
130007
泡棉雙面膠 ×1
Double sided tape
130006
防撞泡棉 (A) ×1
Bumper (A)
130005
工具包 ×1
Tools
130011
210002
C 部品
C parts
210003 ×4
D 部品
D parts
10×15 滾珠軸承 ×8
Ball bearing
120001
5×10 滾珠軸承 ×7
Ball bearing
120002
阻尼器O環 P3 (紅) ×8
Damper O-ring P3 (red)
130001
11.5×1.5 O形環 ×4
O-ring
130002
M3×3 止付螺絲 ×1
Screw
110035
M3×5 止付螺絲 ×1
Screw
110006
M3×10 止付螺絲 ×2
Screw
110032
M3×14 半圓頭螺絲 ×2
Screw
110061
避震上蓋O環×4
Damper cap O-ring
130032
3×8×0.5mm 墊片 ×1
Spacer
110048

7MS-01D RTR
/ S
PARTS
210004
E 部品
E parts
210004-1
直軸組
Spool unit
210020
皮帶齒 18T/36T
18T/36T pulley
210007 ×2
H 部品
H parts
210043
碟型六角輪座組
Wheel hubs w/disc shape
210008 ×2
I 部品
I parts
210009 ×2
J 部品
J parts
210001
底盤
Lower deck
210057 ×2
避震器上下蓋組
Damper cap set
210005 ×2
F 部品
F parts
210006 ×4
G 部品
G parts

8MS-01D RTR
/ S
PARTS
210283
MS 纖維前二樓板 2mm
MS Front upper deck (FRP) 2mm
210284
MS 纖維後二樓板 2mm
MS Rear upper deck (FRP) 2mm
210010
K 部品
K parts
210012
N 部品
N parts
210145R
煞車卡鉗 (電鍍紅)
Brake calipers (red)
210014
O 部品
O parts
210032
伺服機舵片組 (
23T/25T
)
Servo hron set

9MS-01D RTR
/ S
PARTS
210016
R 部品
R parts
以實際搭載為主
Please make
the object as
the standard
4.8×5 球頭 ×8
Ball connector
310001
3×60 拉桿 ×1
Threaded shaft
310002
避震器調整環 ×4
Spring retainer
310004
避震軸心 ×4
Piston rod
310008
轉向支柱 ×2
Steering post
210183
4.8 外六角球頭螺帽 ×2
4.8 Ball connector nut
210161
主齒軸 ×1
Direct center shaft
310009
馬達座 ×1
Motor mount
310010
避震彈簧28mm (中) ×4
Coil spring 28mm (medium)
210144-2
輪軸 ×4
Wheel axle
310006
CVA傳動軸 ×4
CVA swing shaft
310007
大齒盤 48P-88T ×1
Spur gear 48P-88T
210013
馬達齒 48P-26T ×1
Pinion gear 48P-26T
148026
齒比表 Gear Ratio
大齒盤
Spur Gear
馬達齒
Pinion Gear
齒輪比
Gear Ratio
88
(210013)
(OP.148088)
24 7.33
25 7.04
26 6.77
27 6.52
28 6.29
89
(OP.148089)
23 7.74
24 7.42
25 7.12
26 6.85
27 6.59
90
(OP.148090)
22 8.18
23 7.83
24 7.50
25 7.20
26 6.92
91
(OP.148091)
21 8.67
22 8.27
23 7.91
24 7.58
25 7.28
92
(OP.148092)
20 9.20
21 8.76
22 8.36
23 8.00
24 7.67
皮帶 (486) ×1
Drive belt (486)
414486
皮帶 (228) ×1
Drive belt (228)
414228
210111
反胎齒比組
CS pulley set
310042B
鋁合金單向組 (一般型)
Alum. ony way (general)

Motor & ESC: ___________________________ Battery: _________________
_
Gear Ratio: (Spur: _____T / Pinion: _____T )x 2.0 = __________________
_
CS Ratio:
SETUP SHEET
ORINGINAL SETTING
DATE: TRACK:
SURFACE: GRIP:
NOTE:
12
Camber:
6°
Toe-in: +1°
Ride Height: 6 mm Droop: 6 mm
Front Diff.
Front Rollcenter Front Lower Arm Front Damper
Standard Servo
Low Profile Servo
Chassis & Upper Deck
Front Antil-Roll Bar
1.0mm 1.2mm 1.4mm
Plastic Carbon Fiber
FRP
Plastic Carbon Fiber
FRP
Rear Antil-Roll Bar
1.0mm 1.2mm 1.4mm
1234
Rear Damper Stay
Rear Damper
A
B
A
B
Front Lower Arm Rear Lower Arm
Front Wheel Hubs
32.5mm 35.5mm
Rear Wheel Hubs
0mm
0mm
Front Damper Stay Front Upright Rear Upright
1
2
3
Rear Diff
Ballast:
Length: 63 mm Spring: 28 mm Piston: 1.2 mm Shock Oil: 150 Piston Hole: 3 Spring Color: Gold
Length: 63 mm Spring: 28 mm Piston: 1.2 mm
Shock Oil: 150 Piston Hole: 3 Spring Color: Gold
0mm
0mm
0mm
0mm
Camber: 4° Toe-in: 4°
Droop: 7 mm
Ride Height: 5 mm
3
1 2 4
Rear Rollcenter
Rear Lower Arm
0mm
0mm mm
mm
0mm mm
mm 0mm
mm 0mm
mm 0mm
0 mm
0 mm
0 mm
0 mm
Alum. One way
Spool Ball Diff.
Spool
Alum. Spool
Separating Spool Alum. Ball Diff.
Steering Arm
Plastic
Alum. Steering Arm
0mm
FRONT REAR
Tire:____________ ______________
_
Wheel:_________ _______________
_
Offset:________________
Tire:_____________
_______________
Wheel:
_
_________
________________
_
Offset:
_
________________
Front lower arm “A” Front lower arm “B”
4° 7° 10° 14° 0° 4° 7° 10°
Front Caster
1.0 1.38 1.54 1.66 1.82 2.0
88 26 6.77
540 22000rpm & B4222
Plastic
Carbon Fiber FRP
Plastic Carbon Fiber
FRP
RTR/SRTR/S

More details,please refer to MST website.
更多詳細內容，請上官網。
[www.rc-mst.com ]
210146
210122
210121 210148 210204
210135 210136 210134
210142
210123 210211 210210210209210208210207
210143
Steel CVD Shaft Set 42mm
鋼製CVD傳動軸組42mm
Alum. Steering Arm
鋁合金轉向雙搖臂組
Alum. Spool Unit
鋁合金直輪組
Alum. main shaft mount R/L
鋁合金主軸座組
Alum. bulkhead R/L
鋁合金側板組
Alum. Motor Heatsink
鋁合金馬達散熱片
Alum. Separating Spool Unit
鋁合金分離式直軸組
Alum. upper bulkhead R/L
鋁合金側板上蓋組
Alum. Bumper Support
鋁合金防撞板上蓋
Alum. Belt Stabilizer
Mount
鋁可調壓輪座
Alum. Pulley 18T
鋁皮帶輪18T
Alum. Pulley 10T
鋁皮帶輪10T
Alum. Pulley 11T
鋁皮帶輪11T
Alum. Pulley 12T
鋁皮帶輪12T
Alum. Pulley 13T
鋁皮帶輪13T
Alum. wheel hubs
(brake disk shaped)
鋁合金前剎車碟六角輪座
11 MS-01D RTR
/ S
RECOMMENDED OPTION PARTS for MS-01D series

[ www.rc-mst.com ]
[ facebok.com/MST.tw ]
110001 Round head screw M3×6 (10)
110002 Round head screw M3×8 (10)
110003 Round head screw M2.5×6 (6)
110004 Round head screw M2×4 (6)
110005 Flat head screw M3×8 (10)
110006 Set screw M3×5 (6)
110008 Set screw M3×25 (6)
110009 Set screw M3×20 (6)
110010 Round head screw M2.5×14 (6)
110011 Cap screw M3×6 (6)
110012 Flat head screw M3×11 (10)
110013 E-clip E2.0 (10)
110014 Flat head screw M3×13 (10)
110015 Flange nut M4 (4)
110016 R-clip R6 (10)
110017 Shaft 2×9.8 (10)
110018 Shaft 2×13.8 (5)
110019 Shaft 2×11.8 (5)
110023 Set screw M3×16 (6)
110024
Flat head screw M3
×
6 (10)
110025 Taping screw 2.6×10(6)
110026 Round head screw M3×10 (10)
110029 Round head screw M3×12 (6)
110032 Set screw M3×10 (6)
110035 Set screw M3×3 (6)
110061 Round head screw M3×14 (6)
120001 Ball bearing 10×15 (4)
120002 Ball bearing 5×10 (4)
130001 Damper O-ring P3 (red)(10)
130002 O-ring 11.5×1.5 (4)
130003 Battery O-ring (S)(2)
130004 Oil seal (4)
130005 Bumper (A)
130006 Double sided tape (5)
130007 Antenna pipe(2)
130011 Tools
130032 Damper cap O-ring (10)
148026 MST 48P Pinion gear 26T
210001 Chassis
210002 C PARTS
210003 D PARTS
210004 E PARTS
210005 F PARTS
210006 G PARTS
210007 H PARTS
210008 I PARTS
210009 J PARTS
210010 K PARTS
210012 N PARTS
210013 Spur gear 88T-48P
210014 O PARTS
210016 R PARTS
210043 Wheel hubs w/disc shape
210057 Damper cap set
210111 CS pulley set (1.54/1.66/1.82)
210144-2 Coil spring set 28 (medium) (gold) (2)
210145R Brake calipers-red (4)
210161 4.8 ball connector nut (4)
210183 Alum. steering post (2)
210283 MS Front upper deck (carbon look) 2.0
210284 MS Rear upper deck (carbon look) 2.0
310001 Ball connector 4.8×4.5 (5)
310002 Threaded shaft 3×60
310004 Spring retainer (2)
310006 Wheel axle (2)
310007 CVA swing shaft (2)
310008 Piston rod (4)
310009 Direct center shaft
310010 Motor mount
310042 Alum. one way (general)
310043 One way outdrive (general)(2)
414228 Drive belt-228
414486 Drive belt-486
600002 XTR-02 2.4G Transceiver set
601001 22000RPM brushed motor
601002 RTR brushed ESC
601003 RTR servo
110001 六角半圓頭螺絲 M3×6 (10)
110002 六角半圓頭螺絲 M3×8 (10)
110003 六角半圓頭螺絲 M2.5×6 (6)
110004 六角半圓頭螺絲 M2×4 (6)
110005 六角沉頭螺絲 M3×8 (10)
110006 六角止付螺絲 M3×5 (6)
110008 六角止付螺絲 M3×25 (6)
110009 六角止付螺絲 M3×20 (6)
110010 六角半圓頭螺絲 M2.5×14 (6)
110011 六角有頭螺絲 M3×6 (半牙) (6)
110012 十字扁頭螺絲 M3×11 (10)
110013 E扣2.0 (10)
110014 公制十字扁頭螺絲 M3×13 (10)
110015 凸緣螺帽 M4 (4)
110016 R銷6 (10)
110017 插銷 2×9.8 (10)
110018 插銷 2×13.8 (5)
110019 插銷 2×11.8 (5)
110023 六角止付螺絲 M3×16 (6)
110024 六角沉頭螺絲 M3×6 (10)
110025 自攻六角半圓頭螺絲 2.6×10 (6)
110026 六角半圓頭螺絲 M3×10 (10)
110029 六角半圓頭螺絲 M3×12 (6)
110032 六角止付螺絲 M3×10 (6)
110035 六角止付螺絲 M3×3 (6)
110061 六角半圓頭螺絲 M3×14 (6)
120001 培林 10×15 (4)
120002 培林 5×10 (4)
130001 阻尼器O環P3 (紅) (10)
130002 O環11.5×1.5 (4)
130003 電池O環(S) (2)
130004 避震氣室 (4)
130005 防撞泡棉 (A)
130006 泡棉雙面膠 (5)
130007 天線管 (2)
130011 工具包
130032 避震上蓋O環(10)
148026 MST 48P 馬達齒 26T
210001 底盤
210002 C 部品
210003 D 部品
210004 E 部品
210005 F 部品
210006 G 部品
210007 H 部品
210008 I 部品
210009 J 部品
210010 K 部品
210012 N 部品
210013 大齒盤 88T-48
210014 O 部品
210016 R 部品
210043 碟型六角輪座組
210057 避震器上下蓋組
210111 反胎齒比總成 (1.54/1.66/1.82)
210144-2 避震彈簧28 (中) (金) (2)
210145R 煞車卡鉗(電鍍紅) (4)
210161 4.8 外六角球頭螺帽 (4)
210183 轉向支柱(2)
210283 MS 纖維前二樓板 2.0
210284 MS 纖維後二樓板 2.0
310001 內六角公球頭4.8×4.5 (5)
310002 拉桿3×60
310004 避震器調整環 (2)
310006 萬向接杯 (2)
310007 CVA狗骨 (2)
310008 避震軸心 (4)
310009 主齒軸
310010 馬達座
310042 鋁合金單向組 (一般型)
310043 單向接杯 (一般型) (2)
414228 皮帶-228
414486 皮帶-486
600002 XTR-02 2.4G 遙控器組
601001 22000RPM 有刷 馬達
601002 電子變速器 ESC-RTR
601003 SG5010 伺服機
414225 Drive belt-225
414225J Drive belt-225 (Japan)
414486J Drive belt-486 (Japan)
414222J Drive belt-222 (Japan)
910004-L MST T-shirt L
910004-XLMST T-shirt XL
910004-2L MST T-shirt 2L
910004-3L MST T-shirt 3L
210101 Alum. Servo mount (2)
210102 Alum. one way unit
210104 Front ball diff unit
210105 Alum. turnbuckle shaft 3×60 (1)
210108 Alum. turnbuckle shaft 3×28 (2)
210110 Stabilizer set (F/R)
210112 Main shaft mount supporting bar
210113 Rear ball diff unit
210114 Alum. motor heat sink mount
210115 Alum. damper set (4)
210116 Alum. spur gear holder cover (1)
210117 Alum. spur gear holder (1)
210118 Alum. upright (blue) (2)
210119 Front ball diff joint
210120 Alum. high torque servo saver (F/KO)
210121 Alum. spool unit
210122 Alum. steering arm
210123 Alum. belt stabilizer mount
210124 Alum. belt pulley
210125 Carbon front upper deck
210126 Carbon rear upper deck
210127 Carbon front damper stay
210128 Carbon rear damper stay
210129 Carbon bulkhead brace
210130 Carbon lower deck
210131 High torque servo saver (F/KO)
210132 4.8 ball connector (5)
210133 5.8 ball connector (5)
210134 Alum. upper bulkhead R/L (blue)
210135 Alum. main shaft mount R/L
210136 Alum. bulkhead R/L (blue)
210137 4mm Turnbuckle wrench
210140 Carbon battery holder set (black)
210141 Carbon ESC plate
210142 Alum. bumper support
210143
Alum. Wheel Hubs (Brake Disc Shaped)(4)
210144 Coil spring set 28 (8)
210145 Brake calipers (4)
210145B Brake calipers-blue (4)
210145GD Brake calipers-Gold (4)
210146 Steel CVD universal shaft set (2)
210147 Servo Saver Spring (hard) (black)
210148 Alum. motor heatsink
210151 Alum. damper cylinder (4)
210155 Servo Saver Spring(medium)(blue)
210157 Alum. CVD universal shaft set (2)
210159 5.8x4 ball connector (4)
210160 5.8x6 ball connector (4)
210162 Alum. small belt pulley mount
210163 Alum. hex wheel hubs (4)
210165 Alum. turnbuckle 3×20 (blue) (2)
210166 Steel turnbuckle 3×20 (blue) (2)
210167 Alum. turnbuckle 3×25 (blue) (2)
210168 Steel turnbuckle 3×25 (blue) (2)
210178 Front motor mount conversion kit
210190 Reinforced suspension arm set (2)
210192 MS chassis set (8 pieces)
210198 Steel turnbuckle 3×28 (blue) (2)
210204 Alum. separating spool unit
210205 DK Coil spring set 30
210206
Alum. Antenna Pipe Mount (Generalized)
210207 Alum. Pulley 10T
210208 Alum. Pulley 11T
210209 Alum. Pulley 12T
210210 Alum. Pulley 13T
210211 Alum. Pulley 18T
210235 Piston spacer set
210273 Damper spring set 29mm
414225 皮帶-225
414225J 日製皮帶-225
414486J 日製皮帶-486
414222J 日製皮帶-222
910004-L MST T-shirt 衣服 L
910004-XLMST T-shirt 衣服 XL
910004-2L MST T-shirt 衣服 2L
910004-3L MST T-shirt 衣服 3L
210101 鋁合金伺服機座 (2)
210102
鋁合金前單向組 (含前單接杯2/皮帶齒壓板1)
210104 前滾珠差速總成
210105 鋁可調拉桿 3×60
210108 鋁可調拉桿 3×28 (2)
210110 防傾桿組 (半車份/前後通用)
210112 主軸座支撐桿
210113 後金屬滾珠差速器組
210114 鋁合金馬達散熱固定座
210115 鋁合金避震器組 (4)
210116 鋁合金主齒固定板 (1)
210117 鋁合金主齒固定座 (1)
210118 鋁合金轉向輪座 (藍) (2)
210119 前金屬滾珠差速接杯
210120 鋁合金強力伺服緩衝器 (F/KO)
210121 金屬直軸組
210122 鋁合金轉向雙搖臂組
210123 鋁合金可調後皮帶壓輪座
210124 鋁合金後皮帶壓輪
210125 碳纖維二樓板 F
210126 碳纖維二樓板 R
210127 碳纖維避震架 F
210128 碳纖維避震架 R
210129 碳纖維側板補強片
210130 碳纖維底盤
210131 強化伺服緩衝器 (F/KO)
210132 4.8金屬球頭(5)
210133 5.8金屬球頭(5)
210134 鋁合金上蓋組 R/L (藍)
210135 鋁合金主軸座 R/L
210136 鋁合金 板 R/L (藍)
210137 4mm 拉桿板手
210140 碳纖維電池座組 (黑)
210141 碳纖維電變托盤
210142 鋁合金防撞板上蓋
210143 鋁合金剎車碟六角輪座 (1車份)
210144 避震彈簧組28(4種硬度)
210145 煞車卡鉗 (無烤漆) (4)
210145B 煞車卡鉗 (電鍍藍) (4)
210145GD 煞車卡鉗 (電鍍金) (4)
210146 大角度CVD傳動軸組 (2)
210147 緩衝器簧圈/硬(黑)
210148 鋁合金馬達散熱片 (可固定風扇)
210151 鋁合金避震筒身 (4)
210155 緩衝器簧圈/中(藍)
210157 鋁合金CVD傳動軸組 (2)
210159 5.8x4 球頭螺絲 (4)
210160 5.8x6 球頭螺絲 (4)
210162 鋁合金小皮帶壓輪座組
210163 鋁合金六角輪座 (4)
210165 鋁可調拉桿 3×20 (藍) (2)
210166 鋼可調拉桿 3×20 (藍) (2)
210167 鋁可調拉桿 3×25 (藍) (2)
210168 鋼可調拉桿 3×25 (藍) (2)
210178 FS 前置馬達套件
210190 強化擺臂組 (2)
210192 MS 全車銀 板件組 (8件組)
210198 鋼可調拉桿 3x28 (2)
210204 鋁合金分離式直軸組
210205 DK避震彈簧組 30
210206 鋁合金天線管座(通用型)
210207 鋁合金皮帶輪10T
210208 鋁合金皮帶輪11T
210209 鋁合金皮帶輪12T
210210 鋁合金皮帶輪13T
210211 鋁合金皮帶輪18T
210235 避震器活塞墊片組
210273 彈簧組 29mm
PARTS CODE
部品編號
OPTION PARTS CODE
改裝品編號
026003 ver.4.1