Mule Lighting EGX Ever-green Series User manual

UNIVERSAL BACK, END OR TOP MOUNT FOR SINGLE AND DOUBLE FACE SIGNS
BACK MOUNT:
1- Select arrows as required by removing arrow insert(s) in stencil face sheet legend. Remove plasc protector from
window. Discard angle bracket.
2- ENSURE MOUNTING SURFACE IS FLAT WITH NO RAISED AREAS THAT MAY PENETRATE SIGN OR
CAUSE BENDING. Use sign to mark mounng points, and mount sign in posion using maximum size 8 screws.
Up to six screws may be used (mounng screws supplied by installer).
3- Replace legend and window. W indow snaps into housing by locang tabs at six points as shown. Place into posion
by locang two boom tabs. Bend the window outwards slightly at sides to insert side tabs. Two tabs along top edge
may be inserted by flexing wall (EMP models only) or by inserng 1/4" scewdriver, twist to insert tabs {EMA & EMP
models). To remove window, insert flat screwdriver into slots provided and twist to release tabs at two points on top
edge, then flex window to remove.
WINDOW L OCK TAB S
AT SIX POINTS
S CREWDRIVER R ELEAS E SLOTS
DOUBLE FDOUBLE FACE
Self- Luminous Signs
Thermoplasc Housing
LOCK
WASHER
OUTER
WINDOW
STENCIL FACE
SINGLE FACE
TOP MOUNT BACK MOUNT
See diagrams below:
1. Select open holes (not tapped holes), place bracket in mount posion and mark screw anchor locaons
on ceiling or wall surface. Install screw anchors, and install bracket.
2. Aach sign to bracket using two #8-32 Allen- Head screws with lock washers provided.
UNIVERSAL TUNIVERSAL TOP OR END MOUNT
EGX Ever-green Series
SINCE 1923

1. Assemble Angle Bracket to Canopy
Plate using 2 # 8-32 x 1/2" screws,
nuts, & washers.
2. If mounng direct to wall or ceiling,
use Canopy Plate holes to mark screw
anchor and clearance hole posions,
drill and insert anchors.
3. Mount Canopy Plate to selected locaon
using screws supplied.
4. Assemble sign to bracket using 2 #8 screws
provided.
5. Select arrows ; replace legend and window-
see over.
8- 32 X 1 "
SC REWS TO SURFACE
OR BOX
#8 BRACKET SCREWS
WINDOW
Self- Luminous Signs
Thermoplasc Housing
1. Assemble Angle Bracket to Canopy
Plate using 2 # 8-32 x 1/2" screws,
nuts, & washers.
2. If mounng direct to wall or ceiling,
use Canopy Plate holes to mark screw
anchor and clearance hole posions,
drill and insert anchors.
3. Mount Canopy Plate to selected locaon
using screws supplied.
4. Assemble sign to bracket using 2 #8 screws
provided.
5. Select arrows ; replace legend and window-
see over.
8- 32 X 1 "
SC RE WS TO S URFACE
OR BOX
#8 B RA CKE T SC RE WS
WINDOW
E merg en ce
Self- Luminous Signs
Thermoplasc Housing
Series E MP & E MC
S P E C I F I E D E M E R G E N C Y L I G H T I N G
Signtex Inc
LIG H TIN G
1. Assemble Angle Bracket to Canopy
Plate using 2 # 8-32 x 1/2" screws,
nuts, & washers.
2. If mounng direct to wall or ceiling,
use Canopy Plate holes to mark screw
anchor and clearance hole posions,
drill and insert anchors.
3. Mount Canopy Plate to selected locaon
using screws supplied.
4. Assemble sign to bracket using 2 #8 screws
provided.
5. Select arrows ; replace legend and window-
see over.
8- 32 X 1 "
SC RE WS TO S URFACE
OR BOX
#8 B RA CKE T SC RE WS
WINDOW
E merg en ce
Self- Luminous Signs
Thermoplasc Housing
Series E MP & E MC
S P E C I F I E D E M E R G E N C Y L I G H T I N G
Signtex Inc
LIG H TIN G
1. Assemble Angle Bracket to Canopy
Plate using 2 # 8-32 x 1/2" screws,
nuts, & washers.
2. If mounng direct to wall or ceiling,
use Canopy Plate holes to mark screw
anchor and clearance hole posions,
drill and insert anchors.
3. Mount Canopy Plate to selected locaon
using screws supplied.
4. Assemble sign to bracket using 2 #8 screws
provided.
5. Select arrows ; replace legend and window-
see over.
8- 32 X 1 "
SC RE WS TO S URFACE
OR BOX
#8 B RA CKE T SC RE WS
WINDOW
E merg en ce
Self- Luminous Signs
Thermoplasc Housing
Series E MP & E MC
S P E C I F I E D E M E R G E N C Y L I G H T I N G
Signtex Inc
LIG H TIN G
DOUBLE FACE
SINGLE FACE
2 3/4"
4"
CANOPY
LOCATION
CLEARANCE
HOLES 3/8" DIA
SCREW ANCHOR
LOCATIONS-
DIA AS REQUIRED
DRILL LOCA TIONS
CANOPY, TOP, OR END MOUNT
OUTER WINDOW
CANOPY PLATE
#8-32 x 3/8"
ALLEN HEAD
SCREWS &
LOCKWASHER
2 REQUIRED #8-32 x 3/4"
SCREWS
2 REQUIRED
3/8" DIA CLEARANCE HOLES (2 REQD.)
LE GEND
EGX Ever-green Series
SINCE 1923