MULTISPAN PIC-9004 User manual

OPERATING MANUAL
PIC-9004
www.multispanindia.com
Page - 1
Technical Specification
1) Micro Controller Based, Dual Display
2) Display : UPPER: 6 Digit 7 Segment LED Display 2.15” INCH in Red Color
LOWER: 4 Digit 7 Segment LED Display 2.15” INCH in Green Color
3) Dimension Size : 375 X 160 X 70mm
4) Input : Proximity NPN/PNP Selectable
5) Output : 1 Relay 1C/O,230V AC , 5A
6) Power Supply : 100 To 250V AC (SMPS)
7) Range & Decimal Point selectable
FUNCTION DISPLAYS
Set Diameter
Set Speed
Password
Set Length
Decimal Point
Time
RANGE
0-9999.99 mm
(Slow : Max , RPM 500)
(Medium : Max, RPM 5000)
(Fast : Max, RPM 15000)
25 Fix
0 to 999999 Meter






9999.99/99999.9/999999
00.1 to 99.9 sec.
Parameter
PIC 9004
.
.
SET ENT
RST
PIC 9004
METERS

. 
. 
Total Length in Mtr.
Speed in Mtr/Min.
. 

.



Range: 00000.1 to 999999 Meter
Password : 25 FIX
Set Length value by pressing & key
Set Password value by pressing & key
: UP key increases value of individual digit
: UP key increases value of individual digit
: SHIFT key to go to next digit for changing
: SHIFT key to go to next digit for changing
value of the digit.
value of the digit.
set LENGTH
set PASSWORD
Range: 0000.01 to 9999.99 mm
Set Diameter value by pressing & key
: UP key increases value of individual digit
: SHIFT key to go to next digit for changing
value of the digit.
set DIAMETER
Procedure to Program the Length Counter
Page - 2 www.multispanindia.com
. 

Range: 00.1 to 99.9 sec.
Set Diameter value by pressing & key
: UP key increases value of individual digit
: SHIFT key to go to next digit for changing
value of the digit.
set TIME
Set SPEED Selection by pressing key
SLOW: MAX RPM 500
MEDIUM: MAX RPM 5000
FAST: MAX RPM 15000
set SPEED



 Range: 0000.00, 00000.0 & 000000
Set Decimal point by pressing key
set DECIMAL POINT
Press key
to save & Exit.
PIC 9004
ENT
RST

Working
1). The proximity switch give pulse to counter everytime the metal on the roller is sensed.
2). Length of Material ( in meter ) for one revolution = 3.14 X Diameter (mm)
3). Total length = { 3.14 X Diameter (mm) X Number of Revolutions } / 1000
4). Total Meters/Minute = { 3.14 X Diameter (mm) X RPM } / 1000
Note
1). When pulse comes from sensor, upper display indicates increment in ‘Total Length’ in
Meter & Lower Display indicates ‘Speed’ in Meter/Min.
2). For Manual Mode, set time = 00.0 sec & For Auto Reset Mode,
set time = 00.1 to 99.9 sec.
3). In RUN mode, if we press key then upper display shows Batch Count.
4). When Total Length = Set Length, relay-1 energise. Relay-1 remains ON for
Auto Reset Time.Relay turns off after completion of time. If time is set at 00.0 sec.
then relay remains ON until key is pressed.
5). If there is a power failure the last reading is stored in the memory and Counter starts
resume counting from the last stored value, when instument is turned ON.
6). To restart Totalizing or to Reset press key. Upper display will show 00000.0 and the
counting will restart.
Connection Diagram
Page - 3 www.multispanindia.com
PIC 9004
Note:
: Short Pins 3 & 4NPN PROXY
Proxy Connection 4,5 & 6
: Short Pins 5 & 6 PNP PROXY
Proxy Connection 3,4 & 5
N
NO
+12V
I/P 2
I/P 1
GND
Relay
NC
c
L
100-250V AC
50/60 Hz
1
2
3
4
5
6
7
8
9
10
11
12
RESET
ENT
RST
ENT
RST

www.multispanindia.com
Page - 4
PIC 9004
Product improvement and upgrade is a constant procedure. So for more updated operating information and Support,
Please contact our Helping: [phone]/76/82 or Email at ser[email protected] Ver: 05-2018
NOTE: