MULTISPAN AMP 13 User manual

DISPLAY PAGE
1) Voltage L1-L2
2) Voltage L2-L3
3) Voltage L3-L1
4) Frequency
125
L1 AVG
AVG
AVG
AVG
L2 L3
130
L1 L2 L3
128
L1 L2 L3
L1 L2 L3
127
AMP 13
INPUT SPECIFICATION :
DISPLAY AND KEY :
AUXILIARY SUPPLY :
Dimension :
Direct Current AC
Accuracy
3 PHASE AMPERE METER
0.1Amp to 5 Amp AC
Display
Supply voltage
Dimension (mm)
Keys
Power consumption
(VA RATING)
4 digit, 1line, 7 seg, 0.8” RED LED
96 (H) x 96 (W) x 42 (D) mm
SET/ENT, INC, DEC
ENVIRONMENT CONDITION :
Relative Humidity
Protection Level
(As per request)
Operating Temp. 0°C to 55°C
UP to 95% RH
(non-condensing)
IP-65 (Front side) As per IS/IEC
60529 : 2001
100-270V AC 50/60HZ 4VA
TECHNICAL SPECIFICATION
MECHANICAL INSTALLATION
TERMINAL CONNECTION
Class 0.5 (Standard)
ACCURACY
Panel Cutout 92 (H) x 92 (W) mm
Class 0.5
Primary CT 5 to 9999 Amp (Selectable)
Secondary CT 5 or 1 Amp (Selectable)
LED Indication
96
92
92
96
Outline Dimension (mm) Panel Cutout
Dimension (mm)
42
3
AMP 13
L1 L2 L3
A
2405
4 VA MAX
1) L1 Current
2) L2 Current
3) L3 Current
Class 0.5 (Standard)
Outline Dimension (mm) Panel Cutout
Dimension (mm)
AVG
4) Average Current
L1, L2, L3, Avg
123478910
S1 S1 S1 S2S2S2
L1
L2
L3
Range
Model: AMP-13-A2-00
Current: 0.1Amp To 5.00A AC
Accuracy Class: 0.5
L N
CT Primary Selection up to 9999A AC
CT Secondary Selection By 5A /1A AC
www.multispanindia.com
!
Made in India
CAT III
536
100
270V AC
~
50/60 Hz
4VA

KEY OPERATION
To enter in parameter setting
To view individual phase Current
To Scroll & Hold Page
PRESS KEYFUNCTION
OPERATOR MODE
PARAMETER SETTING MODE
It is used to set parameter value
and to be save & exit from menu
To increment value in parameter
setting
To decrement value in parameter
setting
For 5 sec
SET
OR
Read complete instructions prior to installation
and operation of the unit.
WARNING : Risk of electric shock.
SAFETY PRECAUTION
!
All safety related codifications, symbols and instructions
that appear in this operating manual or on the equipment
must be strictly followed to ensure the safety of the operating
personnel as well as the instrument.
If all the equipment is not handled in a manner specified
by the manufacturer, it might impair the protection provided
by the equipment.
WARNING GUIDELINES
WARNING : Risk of electric shock.
1) To prevent the risk of electric shock, power supply to the
equipment must be kept OFF while doing the wiring
arrangement. Do not touch the terminals while power is
being supplied.
2) To reduce electro magnetic interference, use wire with
adequate rating and twists of the same of equal size shall
be made with shortest connection.
3. Cable used for connection to power source, must have a
cross section of 1mm or greater. These wires should have
insulations capacity made of at least 1.5kV.
4) A better anti-noise effect can be expected by using
standard power supply cable for the instrument.
1) Do not allow pieces of metal, wire clippings, or fine
metallic fillings from installation to enter the product or
else it may lead to a safety hazard that may in turn
endanger life or cause electrical shock to the operator.
2) Circuit breaker or mains switch must be installed
between power source and supply terminal to facilitate
power ‘ON’ or ‘OFF’ function. However this mains switch
or circuit breaker must be installed at convenient place
normally accessible to the operator.
INSTALLATION GUIDELINES
3) Use and store the instrument within the specified ambient
temperature and humidity ranges as mentioned in this
manual.
1) The equipment should be cleaned regularly to avoid
blockage of ventilating parts.
2) Clean the equipment with a clean soft cloth. Do not
use isopropyl alcohol or any other cleaning agent.
MAINTENANCE
3) Fusible resistor must not be replaced by operator.
+
ENT
SET
ENT
SET
ENT
1. Prepare the panel cutout with proper dimensions as
shown bove.
2. Fit the unit into the panel with the help of clamp given.
3. The equipment in its installed state must not come in
close proximity to any heating source, caustic vapors, oil
steam, or other unwanted process byproducts.
4. Use the specified size of crimp terminal (M3.5 screws) to
wire the terminal block. Tightening the screws on the
terminal block using the tightening torque of the range of
1.2 N.m.
5. Do not connect anything to unused terminals.
MECHANICAL INSTALLATION
PARAMETER SETTING
PRESS KEYFUNCTION
OPERATOR MODE
PARAMETER SETTING MODE
It is used to set parameter value
and to be save & exit from menu
To increment value in parameter
setting
To decrement value in parameter
setting
SET
!
+
ENT
SET
ENT
SET
ENT
Password
(CT Primary Current )
(CT Primary current value)
(CT Secondary Current )
pasS
19
Pr1
280 (5 - 9999 Amp )
(CT Secondary Current Value)
Press key for save & exit
SET
Press key
SEC
Press key for 5 sec
Enter Password 19
(5 Amp or 1 Amp )
210
pasS
19
Pr1
5
SET
SEC
Press key for 5 sec
Enter Password 19
5
Change by &
Change by &
Change by &
For 5 sec
Press key
Press key
Press key
Press key
Specifications are subject to change, since development is a continuous process,
So for more updated operating information and Support,
Please contact our Helpline: 9978991482/9978991476/9978991474 or
Email at Ver:2105[email protected]