MULTISPAN AV-11V User manual

AV 21V
AV 31V
V
~
AV 41V
AV 11V
230
230
230 230
V2
V1
LN
500V AC
I/P
www.multispanindia.com
100
270V AC
~
Accuracy: 0.5
Made in India
!
CAT III
12347 8 9 10
56
V1 V2
Range: 500V AC
Input
230V AC
50Hz,4VA
LN
!
Accuracy Class: 0.5
www.multispanindia.com
Made in India
CAT III
12347 8 9 10
56
V1 V2
Range: 500V AC
Input
230V AC
50Hz,4VA
LN
!
Accuracy Class: 0.5
www.multispanindia.com
Made in India
OPERATING MANUAL
VOLT METER SERIES
AV-11V,21V,31V,41V
www.multispanindia.com
Page - 1
Power Supply
Protection Level
Relative
Humidity
(As per request)
230V AC, 50Hz 100 to 270V AC
IP-65(Front side) AS per IS/IEC 60529:2001
Model
Display
Size(HXWXD)
Panel Cutout
Input Voltage
46 X 92 mm
68 X 68 mm
92 X 92 mm
48 X 96 X 26mm
72 X 72 X 35mm
96 X 96 X 42mm
Technical Specification
AV-11V AV-21V AV-31V AV-41V
3 Digit 7 seg 0.56”,red LED Display
45 X 45 mm
0° To 55°C
Up to 95% RH Non Condensing
Operating
Temperature
Connection Diagram
AV-11V,21V,31V,41V
L N L N
MeasureVoltage MeasureVoltage
5 to 500V AC
3 Digit 0.8”
48 X 48 X 46mm
Wire Connection 1ø - 2 Wire
~
V2
V1
LN
500V AC
I/P
www.multispanindia.com
100
270V AC
~
Accuracy: 0.5
Made in India
!
AV-31V
CAT III
12347 8 9 10
56
V1 V2
Range: 500V AC
Input
230V AC
50Hz,
LN
!
Accuracy Class: 0.5
www.multispanindia.com
Made in India
AV-11V
~
AV-21V
~
17
23456
LN
!
100
270V AC
~
V1 V2
Range: 500V AC CAT III
~
Accuracy: Class 0.5
Made in India
www.multispanindia.com
INPUT
AV-41V
Accuracy:
Class 0.5
Range:
500V AC
CAT III
6
7
8
9
10
V1
VOLT I/P
V2
1
2
3
4
5
L
N
!
100 ~
270V AC
MadeinIndia
www.multispanindia.com
~
N
L
V2V1
CT
Selection
100
270V AC
~
500V AC
I/P

All safety related codifications, symbols and instructions that appear in this operating manual
or on the equipment must be strictly followed to ensure the safety of the operating personnel as
well as the instrument.
If all the equipment is not handled in a manner specified by the manufacturer, it might impair the
protection provided by the equipment .
=> Read complete instructions prior to installation and operation of the unit.
WARNING : Risk of electric shock.
3) Cable used for connection to power source, must have a cross section of 1mm or greater. These wires
should have insulations capacity made of at least 1.5kV.
2) To reduce electro magnetic interference, use wire with adequate rating and twists of the same of equal size shall
be made with shortest connection.
1) To prevent the risk of electric shock power supply to the equipment must be kept OFF while doing the wiring
arrangement. Do not touch the terminals while power is being supplied.
4) A better anti-noise effect can be expected by using standard power supply cable for the instrument.
1) This equipment, being built-in-type, normally becomes a part of main control panel and such in case the
terminals do not remain accessible to the end user after installation and internal wiring.
2) Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to enter the product
or else it may lead to a safety hazard that may in turn endanger life or cause electrical shock to the operator.
3) Circuit breaker or mains switch must be installed between power source and supply terminal to
facilitate power ‘ON’ or ‘OFF’ function. However this mains switch or circuit breaker must be
installed at convenient place normally accessible to the operator.
4) Use and store the instrument within the specified ambient temperature and humidity ranges as
mentioned in this manual.
Maintenance
1) Prepare the panel cutout with proper dimensions as show above.
2) Fit the unit into the panel with the help of clamp given.
3) The equipment in its installed state must not come in close proximity to any heating source,
caustic vapors, oils steam, or other unwanted process by products.
4) Use the specified size of crimp terminal (M3.5 screws) to wire the terminal block. Tightening the
screws on the terminal block using the tightening torque of the range of 1.2 N.m.
5) Do not connect anything to unused terminals.
1) The equipment should be cleaned regularly to avoid blockage of ventilating parts.
2) Clean the equipment with a clean soft cloth. Do not use isopropyl alcohol or any other cleaning agent.
3) Fusible resistor must not be replaced by operator.
2
95mm - 3.75 inches
85mm - 3.34 inches
136mm - 5.35 inches
120mm - 4.72 inches
B
B
B
A
A
A
F
E
MODEL A
96mm 96mm 92mm 92mm 3mm 52mm
BC
D E F
DIMENSIONS
MODEL A
72mm 72mm 68mm 68mm 3mm 85mm
BC
D E F
DIMENSIONS
C
C
C
D
D
D
E
F
136mm - 5.35 inches
60mm - 2.36 inches
F
E
MODEL A
48mm 96mm 44mm 92mm 4.5mm 66mm
BC
D E F
DIMENSIONS
Warning Guidelines
Safety Precautions
Installation Guidelines
Mechanical Installation
A
B
C
D
EF
MODEL A
48mm 48mm 45mm 45mm 3mm 70mm
BC
D E F
DIMENSIONS
136mm - 5.35 inches
120mm - 4.72 inches
www.multispanindia.com
Page - 2
AV-11V,21V,31V,41V
AV 11V
230
AV 21V
230
AV 31V
V
~
230
AV 41V
230