My Weigh iBalance i3100 User manual

BALANCE

Thank you for purchasing the My Weigh® iBalance® 3100™ digital scale. Please read all operating instructions carefully before use.
This electronic scale is a precision instrument. With normal care and proper treatment, it will provide years of reliable service. For
more information please visit www.myweigh.com
Never load the scale with more than the maximum capacity. Although the iBalance® 3100™ is designed to be extremely durable with
extra overload protection built into the case, overloading will permanently damage it! Avoid any exposure to extreme heat or cold,
your scale works better when operated at normal room temperature. Keep your scale in a clean environment. Dust, dirt, moisture,
vibration, air currents and/or a close proximity to other electronic equipment can all cause an adverse eect on the reliability and
accuracy of your scale. Handle with care. Gently apply all items to be weighed onto tray top. Avoid shaking, dropping or otherwise
shocking the scale. Scales are delicate instruments and unlike cellular phones, scales have delicate sensors that determine how much
an item weighs. If you drop or shock your scale, these sensors“feel”the shock and are sometimes destroyed. This happens with all
digital scales. We design our scales to be as resistant to shock or drops as possible, however there is no way for us to protect 100%
against load cell or sensor damage.
Failure to follow these instructions will void your warranty.
Always allow the scale to acclimate to normal room temperature for at least one hour before use. Give your scale sucient warm up
time. Usually 30-60 seconds before calibration to give the internal components a chance to stabilize.
PRECAUTIONS BEFORE USING THE BALANCE
1. Matter charged with static electricity can aect accuracy. Discharge all static electricity. For example, one method is to use
Static-Guard spray, and spray it on both sides of the weighing platform.
2. The balance must be in an exactly horizontal position in order to achieve accurate measurement results. In order to bring the
balance into a horizontal position, the adjustable feet are turned either clockwise or counter-clockwise until the air bubble on the
front panel is in the center of the marked circle.
3. Please use an independent power outlet to avoid interference from other electrical appliances.
4. Don’t place any objects on the platform before powering on.
5. When possible please allow the scale to warm up for several minutes before operation.
6. Items should always be placed on the center of the platform when being weighed.
Capacity
3100g x 0.01g
6.8lb x 0.0002oz
USER MANUAL
BALANCE
ENGLISH

DISPLAY SYMBOLS
• Scale is in ZERO mode.
• Scale is in TARE mode.
• BATTERY needs recharging.
• The display reading is STABLE.
KEYPAD FUNCTIONS
ON/OFF power switch.
SAMPLING & COUNTING.
UNIT selection
TARE is used to deduct the weight of an
item or container. The symbol will
appear and reading will go to zero. Press it
again to exit the tare mode (when empty),
the tare indication will disappear.
CAL is used for entering calibration and
other function settings
SCALE FEATURES
DATA TRANSMISSION PORT
on right side of the scale
ADJUSTABLE FEET
on bottom of each corner of the scale
OPTIONAL CLEAR WIND SCREEN
AIR BUBBLE LEVEL

POWER SUPPLY
The i3100™ is powered by DC 6 V rechargeable battery or directly by power adapter.
OPERATION INSTRUCTIONS
Weighing Procedures
1.Press to turn on the scale.
When the power is turned on, the scale will countdown for a few seconds and "0" will appear on the display.
2.Select the weighing unit with key.
Press to select a weighing unit.
Once the unit has been selected, the selected unit will be displayed next to the weight value.
3.Start weighing
Verify the reading is "0". Place objects on the weighing platform to weigh.
When the reading becomes stable, the stable indicator is displayed.
Tare
Tare can be used for eliminating the weight value of an empty container. Place an empty container on the scale and press .Then
place the items to be weighed in the container. NOTE: When all weight is removed from the weighing tray, the tared value of a
container will be displayed as a negative number. Press again to return the scale to zero.
ERROR MESSAGES
When an applied load exceeds the capacity, “------” will appear on the display. Remove excessive load immediately. The unit may
return to normal operation. Remember: You can permanently damage the scale and void your warranty by overloading it! The LCD
will display“ERR ”if the weight placed on the platform is incorrect during calibration.
CALIBRATION
When to calibrate - calibration is RARELY required.
Calibration may be required when the scale is rst set up for use, or if the scale is moved to a dierent altitude or new location. This
is necessary because the weight of a mass in one location is not necessarily the same in another location. Also, with time and use,
mechanical deviations can occur.
How to calibrate: **you must have an accurate 1kg weight or combination of weights in order to calibrate**
1. Press and hold , release when the LCD shows“CAL”.
2. The display now shows“1000.00”. This is where you input the calibration weight you are going to use to calibrate (1000 grams is
recommended). Use to cycle through the numbers shown on the screen and use on the selected digit to adjust selected
digit. To calibrate using the recommended 1000 grams, the screen must read “1000.00”. Once this is set, place the 1000 gram
calibration weight on the tray.
3. The display will show“OK”and return to normal weighing mode. Calibration is complete.

Thank you for purchasing the My Weigh® iBalance® 3100™ digital scale. Please read all operating instructions carefully before use.
This electronic scale is a precision instrument. With normal care and proper treatment, it will provide years of reliable service. For
more information please visit www.myweigh.com
Never load the scale with more than the maximum capacity. Although the iBalance® 3100™ is designed to be extremely durable with
extra overload protection built into the case, overloading will permanently damage it! Avoid any exposure to extreme heat or cold,
your scale works better when operated at normal room temperature. Keep your scale in a clean environment. Dust, dirt, moisture,
vibration, air currents and/or a close proximity to other electronic equipment can all cause an adverse eect on the reliability and
accuracy of your scale. Handle with care. Gently apply all items to be weighed onto tray top. Avoid shaking, dropping or otherwise
shocking the scale. Scales are delicate instruments and unlike cellular phones, scales have delicate sensors that determine how much
an item weighs. If you drop or shock your scale, these sensors“feel” the shock and are sometimes destroyed. This happens with all
digital scales. We design our scales to be as resistant to shock or drops as possible, however there is no way for us to protect 100%
against load cell or sensor damage.
Failure to follow these instructions will void your warranty.
Always allow the scale to acclimate to normal room temperature for at least one hour before use. Give your scale sucient warm up
time. Usually 30-60 seconds before calibration to give the internal components a chance to stabilize.
PRECAUTIONS BEFORE USING THE BALANCE
1. Matter charged with static electricity can aect accuracy. Discharge all static electricity. For example, one method is to use
Static-Guard spray, and spray it on both sides of the weighing platform.
2. The balance must be in an exactly horizontal position in order to achieve accurate measurement results. In order to bring the
balance into a horizontal position, the adjustable feet are turned either clockwise or counter-clockwise until the air bubble on the
front panel is in the center of the marked circle.
3. Please use an independent power outlet to avoid interference from other electrical appliances.
4. Don’t place any objects on the platform before powering on.
5. When possible please allow the scale to warm up for several minutes before operation.
6. Items should always be placed on the center of the platform when being weighed.
COUNTING FUNCTION
1. Press to cycle through the weighing modes until the display will show“ CA 10 PCS”(means sample size is 10 pcs)
2. Press to toggle sample size,“10”,“20”,“50”,“100”,“200”,“500”,“1000”pcs will appear in. Stop at the one you want to use.
3. Put the exact quantity of samples desired on the platform and press , the set sample size will appear.
4. Keep adding objects to be counted on the pan, the total number of the objects will be displayed. If the unit weight is too small for
the counting resolution, the display will show“Err”
5. To return to normal weighing press
WEIGHT RESPONSE SPEED
The i3100 allows you to adjust the scale reaction time and division selction.
1. Press and hold (do not release) and power the scale on with . Wait until the display shows“nb0 - nb4”and release
2. Press to select your response speed. (nb0: fastest, nb4 slowest) Press to conrm.
COMMUNICATION AND BACKLIGHT
1. Press and hold and press to power the scale on. The scale will power on and go through the self test.
COMMUNICATION
2. The scale should now read “bAUd” followed by“12”, “24”, “48”or“96”. These values represent the baud rate settings: 1200, 2400,
4800, 9600.
3. Use to scroll through the settings and press to conrm.
4. The display will now read “Pr”(Press Sending),“Co”(Stable Sending”or“St”(Continuous Sending)
5. Use to scroll through the settings and then press to conrm
BACKLIGHT
6. The display should now read“bL On”(Backlight ON),“bL OFF”(Backlight OFF) or“bL AUTO”(Automatic Backlight).
7. Use to scroll through the settings and press to conrm
8. Once is pressed the scale will return to normal weighing.
SELECTING DESIRED WEIGHING MODES
The 3100™comes with a preset 9 units with the option to add another 9 units if required. To enable or disable each unit weighing
modes follow these steps:
1. Press and hold and together, then press and release , the scale will power on. Release all the keys when the
display shows“PASS”.
2.Press 4 times and the display will show“YES”and the corresponding unit. Press again to enable (yes) or disable (no) the
selected unit.
3.Press to move to the next unit.The scale will return to normal weighing mode when all the unit settings are nished.

DATA TRANSMISSION – SERIES RS-232 INTERFACE (only for communication)
1. iBalance 0232C,s -RS232 C’s UART signal
2. Format
(1) Baud rate: 1200 bps 2400 bps 4800bps 9600 bps
(2) Data bits: 8 bits
(3) Parity bit: none
(4) Stop bit: 1 bit
(5) Code ASCII
DATA FORMAT：
HEAD1 HEAD2 DATA UNIT CR
12 3 4 56 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
HEAD1 (2BYTES) HEAD2 (2BYTES)
OL - overload NT - net weight mode
ST - stable US - unstable
DATA(8BYTE)
2D (HEX) =“- ”(negative sign) 20 (HEX) =“ ”(blank)
2E (HEX) =“. ”(decimal point)
UNIT (4 byte)
g = 20 (HEX); 20 (HEX); 20 (HEX); 67 (HEX)
kg = 20 (HEX); 20 (HEX); 6B (HEX); 67 (HEX)
ct = 20 (HEX); 20 (HEX); 63 (HEX); 74 (HEX)
ozt = 20 (HEX); 6F (HEX); 7A (HEX); 74 (HEX)
CR = OD (HEX); OA (HEX)
TRANSMISSION EXAMPLE
stable net + 0.168 g
HEAD, HEAD, DATA UNIT CR
ST, NT + 0.168 g OA, OD
PRESET UNITS ADDITIONAL UNITS
g, ct, oz, ozt, lb, dr, gn, dwt, gsm, PCS , MM, tl.J, tl.T. tl.H,
t, 1/8, 1/4, TMr, TAR
UnitsCapacity
SPECIFICATIONS
267mm x 191mm x 70mm
127mm x 146mm
DC 6 V Rechargeable Battery or power adaptor
Optimum 10-40°C (50-104°f)
3100g x 0.01g
Scale dimension
Tray dimension
1100gScale Weight
Up to scale’s maximum capacityTare range
Operating temperature
Power Source
PRECISION
0.01g
• g GRAM
• ct CARAT
•oz OUNCE
• ozt TROY OUNCE
• lb POUND
• dr DRAM
• gn GRAIN (UK)
• dwt PENNY WEIGHT
•gsm GRAMS PER METRIC SQUARED
• MM MOMME (JPN)
• tl.J JEWELRYTAEL (HONG KONG)
• tl.T TAEL (TWN)
• tl.H TAEL (HONG KONG)
• t TOLA (INDIA)
• 1/8 1/8 OUNCE
• 1/4 1/4 OUNCE
•TMr TOLA, MASHA, RATTI
• TAr TOLA, ANNIE, RATTI