MyBinding CombBind 110 User manual

0
CombBind 110
™C110
CombBind
Edge Guide
Guia de corte
Guide de bord
Figure 1
Figura 1
1/4”
6mm
5/16”
3/8”
8mm
10mm
1/2”
5/8”
12mm
3/4”
16mm
1”
”
20mm
COMB
1-
25mm
SIZE
1/4”
1-
32mm
1/2
38mm
Binding Handle
Mango de encuadernacion
Poignee de reliure
Figure 3
Figura 3
™C110
bBind
Com
Figure 2
Figura 2
Figure 4
Figura 4
Figure 5
Figura 5

0
Please read these instructions carefully and keep them in a safe place for later reference.
A. DETERMINE SHEET WIDTH:
1. Rotate the edge guide to the paper / cover size
you wish to bind. Letter (8-1/2" x 11") A-4
(297mm x 210mm) Oversized (8-3/4" 222mm x
11-1/4" 286mm) (see figure 1). When using
oversized covers, rotate the edge guide to the
oversize position, punch all of the covers for
your documents and set aside. Rotate the edge
guide to either Letter or A-4 position and punch
the paper for your document.
B. PUNCHING PAPER: (see figure 2)
1. Jog or align the sheets or covers and insert the
edge to be punched into the punch throat opening.
2.Fully insert the sheets into the throat
opening and against the edge guide.
3. To punch, pull the punching handle down
towards you until the handle bottoms and
the punching is complete. The CombBind
C-110 will punch up to 15 sheets of 20 lb. /
80 gsm paper. Do not punch more than (1)
clear cover at a time to prevent jams.
C. DETERMINE PLASTIC COMB SIZE: (see fig. 3)
1. Rotate the binding handle towards you to open
the hooks away from the comb support.
2. Place the document including the covers straight
up against the comb support to the right side
aligning with the binding size scale. Rotate the
binding lever away from you to close the hooks
until they make contact with the document.
3. Read the line closest to the document follow it
to the right to the corresponding comb binding
element size. This is the comb binding element
size required to bind the document. Your
CombBind C-110 can bind books up to 300
sheets. Or 1-1/2" (38mm). For best results,
always use GBC brand covers with GBC color-
coordinated binding combs.
D. BINDING (see figure 4)
1.Before starting make sure hooks
are in the home position.
2. Place the plastic comb binding element
behind the vertical comb with the open
portion of the element facing you.
3. Rotate the binding lever toward you
until the comb binding element opens
sufficiently to insert your document.
4. Place the front cover (finished side down) onto
the opened binding element fingers. Place the
document pages (face down) onto the element.
Repeat for larger documents as required. Place
the back cover (finished side up) on the open
binding element fingers last.
5. Rotate the binding lever away from you, back to
its original position to close the binding element.
6. Remove the book by lifting upward.
Your document is now complete.
7. Once you become familiar with your CombBind
C-110 you will find that you can bind as you
punch, increasing your productivity.
E. EMPTY CHIP DRAWER: (see figure 5)
1. Your CombBind C-110 has a chip drawer
located on the right side of the machine.
When it is full of punched paper chad Gently
pull the drawer to open it and remove from
machine, empty and re-insert the drawer back
in machine until it snaps in place.
F. Service:
1. Contact an authorized GBC service
representative for any required repairs.
Specifications C110
Max. width of paper: 11.7" (297mm - A4)
Punching capacity, paper: 15 sheets (20 lb./80gsm)
Binding capacity: 300 sheets (1-1/2"/38mm)
Net weight: 15.6 lbs. (7.1 kg.)
Dimensions (H x W x D): 18-1/2" (470mm) x 14" (356mm) x 13" (330mm)
Subject to technical changes without prior notice.