NANLUX TK-140B User manual

USER MANUAL
WWW.NANLUX.COM
TK-140B/TK-280B
LED BICOLOR SOFT PANEL LIGHT

USER MANUAL
1. ADDRESS/DMX
2. DMX Remote Control
3. 2.4G Remote Control
4. RDM Remote Control
5. LUMENRADIO Remote Control
01
......................................................
01
...........................................................
02
.........................................................
................................................ 03
.................................................... 04
............................................................
....................................................
....................................................
....................................................
.......................................
.............................
.....................................................................
................................................................
Contents
Product Diagram
Technical Data
Product Details
Detailed Description
Power Connection
Remote Control
Operating Instructions
1. Screen Interface Display Instructions
2. CCT Key
3. EFFECT Key
16
16
18
4. MENU Key
① OUTPUT MODE
② ADDRESS/DMX
③ WIRELESS PROTOCOL
④ LUMENRADIO SETTINGS
⑤ ROTATE SCREEN
⑥ SCREEN BRIGHTNESS
⑦ BUTTON BACKLIGHT
⑧ LANGUAGE
⑨ VERSION
33
34
34
34
35
36
37
38
39
33
395. LOCK Key
Safety Precautions
Notice
Product Includes
07
10
12
13
14 40
............................................
..............................................................
.............................................................
..........................................................
.............................................
...........................................
...................................................
.........................................
............................................
.....................................................
.....................................................
.............................................................
40
....................................................................
41
................................................
General Fault Detection and Diagnosis ....... 40

1
TK-140B/TK-280B
Product Diagram
LED Bi-color Soft Panel Light
Model No.: TK-140B
Rated power: 160W
Input voltage/current: DC24V/6.67A Max
AC100-240V 50/60Hz
CCT: 2700K - 7500K
CRI: Average 95
TLCI: Average 98
Model No.: TK-280B
Rated power: 280W
Input voltage/current: DC48V/5.84A Max
AC100-240V 50/60Hz
CCT: 2700K - 7500K
CRI: Average 95
TLCI: Average 98
Technical Data
TK-280B
TK-140B

2
Product Details
2. Fixture body handle
3. Kipp handle
9. Mounting plate
10. User interface
11. Safety cable ring
12. Power switch
13. DC IN
14. Barndoor
1. Battery holder
2. Fixture body handle
3. Kipp handle
4. Yoke
6. USB port
5. Power indicator
7. DMX IN
8. DMX OUT

3
Detailed Description
1. Battery holder: For installing the 14.4-26V/12A V-mount battery or the power supply.
2. Fixture body handle: For lift the fixture and adjust the direction of the fixture.
3. Kipp handle: Tighten or release the tilt movement of the fixture on the yoke.
4. Yoke: Mount the fixture on a stand; pan and tilt.
5. Power indicator: Check the status of the power input. Indicator always on: normal power supply; Indicator flashing or off: abnormal power supply or no power input.
6. USB port: Install firmware updates.
7. DMX IN: DMX signal input interface.
8. DMX OUT: DMX signal output interface.
9. Mounting plate: For installing gooseneck base or 5/8 pin base.
10. User interface: Display and control functions, operations and data.
11. Safety cable ring: Attach safety rope to secure the diffuser.
12. Power switch: Turn on/off the fixture.
13. DC IN: DC power Input interface.
14. Barndoor: For controlling the spill of light.

4
Power Connection
1. Conection between the light fixture and power supply

5
NOTE:
① When connecting the power supply, please make sure the power voltage and frequency is consistent with the provided power supply.
② Make sure to use the provided power supply and power cable. The connection between plug on power supply and the power cable on the fixture should be
connected as following.
DC IN
1-
2-
4+
3+
4+
3+
1-
2-
·TK-140B
·TK-280B
1+
1-
1+
1-

6
2. Connection between the light fixture and battery
① TK-140B can be powered by one or two 14.8V batteries, or powered by one or two 26V batteries. The max power output is 75% when powered by one 14.8V
battery.
② TK-280B can be powered by two 14.8V batteries, or powered by one or two 26V batteries, The max power output is 75% when powered by one 26V battery.
③ Please do not power the fixture with14.8V and 26V batteries at the same time.
④ If there are much differences in current battery level between the two batteries and the two batteries cannot suppl power at the same time, the max power output
will be reduced to 75%
⑤ The battery is sold separately.
BatteryBattery

7
Remote Control
· TK-140B/TK-280B supports remote control via DMX, 2.4G, RDM, LUMENRADIO, and has built-in bluetooth.
▲The ADDRESS needs to be set before operating the remote control via DMX, 2.4G, RDM and LUMENRADIO.
① ADDRESS
Press MENU key to access options.
1. ADDRESS/DMX, including ADDRESS, DMX MODE and DMX DIMMING CURVE setting.
Rotate "Upper knob" to select ADDRESS and press "Upper knob" to enter the correspoding sencondary menu.
OUTPUT MODE
ADDRESS/DMX
WIRELESS PROTOCOL
LUMENRADIO SETTINGS
ROTATE SCREEN
SCREEN BRIGHTNESS
MENU CH: 512
OUTPUT MODE
ADDRESS/DMX
WIRELESS PROTOCOL
LUMENRADIO SETTINGS
ROTATE SCREEN
SCREEN BRIGHTNESS
MENU CH: 512
ADDRESS
DMX MODE
DMX DIMMING CURVE
MENU CH: 512
PRESS “MENU” TO RETURN

8
Rotate "Upper knob" to ADDRESS and press "Upper knob" to enter correspoding third menu.
Rotate ''Upper knob'' to select the ADDRESS and press ''Upper knob'' to set.
NOTE: TK-140B/TK-280B has 10 channels, for multiple lights remote control via DMX, 2.4G, RDM, LUMENRADIO, the address of the first light is set to 001,
the second one is 012, the third one is 023 and so on.
ADDRESS
DMX MODE
DMX DIMMING CURVE
MENU CH: 512
PRESS “MENU” TO RETURN
MENU
PRESS “MENU” TO RETURN
ADDRESS
512
CH: 512
MENU
PRESS “MENU” TO RETURN
ADDRESS
512
CH: 512 MENU
PRESS “MENU” TO RETURN
SET
CH: 512

9
② DMX MODE
Rotate ''Upper knob'' to DMX MODE and press ''Upper knob'' to enter the correspoding secondary menu.
Rotate ''Upper knob'' to select the desired DMX MODE and press ''Upper knob'' to set.
MENU
PRESS “MENU” TO RETURN
SET
CH: 512
ADDRESS
DMX MODE
DMX DIMMING CURVE
MENU CH: 512
PRESS “MENU” TO RETURN
CCT MODE - 8bit
CCT MODE - 1bit
ULTIMATE MODE - 8bit
MENU CH: 512
PRESS “MENU” TO RETURN
CCT MODE - 8bit
CCT MODE - 1bit
ULTIMATE MODE - 8bit
MENU CH: 512
PRESS “MENU” TO RETURN

10
2. DMX Remote Control
① Connect the light fixture and the DMX512 console by connection cable and the method is as below.
③ DMX DIMMING CURVE
DMX IN DMX OUT
1 GND
2 DATA-
3 DATA+
NC
NC
NC
NC
GND 1
DATA- 2
DATA+ 3
Rotate ''Upper knob'' to DMX DIMMING CURVE and press ''Upper knob'' to enter the correspoding secondary menu.
Rotate ''Upper knob'' to select the desired DMX DIMMING CURVEand press ''Upper knob'' to set.
ADDRESS
DMX MODE
DMX DIMMING CURVE
MENU CH: 512
PRESS “MENU” TO RETURN
LINEAR
EXPONENT
LOGARITHM
S CURVE
MENU CH: 512
PRESS “MENU” TO RETURN
LINEAR
EXPONENT
LOGARITHM
S CURVE
MENU CH: 512
PRESS “MENU” TO RETURN
MENU
PRESS “MENU” TO RETURN
SET
CH: 512

11
· The connection between the light fixture and DMX512 console, light fixture and light fixture should use five core shielded cable and make sure its diameter is not
less than 0.3mm. XLR plug/socket and the wire should be connected as the picture aboved.
· Pin1, Pin2, Pin3 for connecting DMX singal, Pin4, Pin5 is connectionless.
▲ Note: When connect with socket, make sure the internal pin not be in contact with the inner case.The fixture can match the the DMX512 (1990) control signal.
· Plug of five-core and three-core XLR plug/socket conversion.
The fixture comes with five-core XLR plug. lf you use the three-core XLR plug, kindly follow below instruction.
② DMX-in Port
ln DMX mode, make sure the last light is the only light with a cable connected to DMX output. There is a resistance about 120(OHM) between the second pin and
third pin of this plug (as shown).
Make sure this plug can be installed into the output of the last fixture, this will help avoid noise and reflection phenomenon caused by the DMX512 signal during
the transmitting process.
③ Set the address of the fixture.
④ Refer to the attached DMX reference guide and control the light via DMX512 console.
(For specific operation methods, please refer to the DMX512 console operation manual.)
Note: DMX Reference Guide《TK-140B/TK-280B DMX Reference Guide (NANLUX)》please download from www.nanlux.com
Three Pin
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Five Pin
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pin 4: N/C
Pin 5: N/C
DMX circuit connection connect
a 120(OHM) resistance between
the 2pin and 3pin of theXLR plug
and then connect it to the DMX
output socket of the last fixture.
PIN 2 PIN 3120Ω
1
3
2

12
3. 2.4G Remote Control
Set the address of the 2.4G remote controller to be consistent with the light fixture, then the light fixture can be remotely controlled by 2.4G remote controller or by
APP via the 2.4G transfer device.
Rotate "Upper knob" to WIRELESS PROTOCOL and press "Upper knob" to enter the corresponding sencondary menu.
Rotate "Upper knob" to select V1.0 or V2.0 and press "Upper knob" to set.
Note: ① 2.4G remote controller and 2.4G transfer device are sold separately.
② The fixture supports the 2.4G wireless protocol V1.0 and V2.0. Set fixture to V2.0 while using WS-RC-C1 or WS-RC-C2 remote control. Set fixture to V1.0
while using other remote controls.
OUTPUT MODE
ADDRESS/DMX
WIRELESS PROTOCOL
LUMENRADIO SETTINGS
ROTATE SCREEN
SCREEN BRIGHTNESS
MENU CH: 512 MENU CH: 512
PRESS “MENU” TO RETURN
2.4G WIRELESS PROTOCOL
V1.0 V2.0
MENU CH: 512
PRESS “MENU” TO RETURN
2.4G WIRELESS PROTOCOL
V1.0 V2.0 SET
MENU CH: 512
PRESS “MENU” TO RETURN

13
4. RDM Remote Control
① Connect the light fixture to the console with RDM function using a connection cable, the connection method is the same as with a DMX512 console.
② Control the fixture via a console with RDM function.
(For specific operation methods, please refer to the RDM console operation manual.)
Note: The UID format of the fixture is as follows:
0008 XXXX XXXX
Serial number
0301：TK-140B
0302：TK-280B
Manufacture: Nanguang

14
5. LUMENRADIO Remote Control
· TK series has built-in TIMO RX module, enabling it to receive CRMX wireless DMX signal. The opreation method is as following:
OUTPUT MODE
ADDRESS/DMX
WIRELESS PROTOCOL
LUMENRADIO SETTINGS
ROTATE SCREEN
SCREEN BRIGHTNESS
MENU CH: 512
Rotate "Upper knob" to LUMENRADIO SETTINGS and press ''Upper knob'' to enter the correspoding secondary menu.
① Set the fixture that need to receive CRMX wireless DMX signals to UNLINK.
Press the ''MENU'' Key to access options.
OUTPUT MODE
ADDRESS/DMX
WIRELESS PROTOCOL
LUMENRADIO SETTINGS
ROTATE SCREEN
SCREEN BRIGHTNESS
MENU CH: 512
UNLINK
MENU CH: 512
PRESS “MENU” TO RETURN

15
Rotate "Upper knob" to enter the next menu.
Rotate "Upper knob" to select YES and press "Upper knob" to set.
MENU
PRESS “MENU” TO RETURN
SET
CH: 512
Note: The LUMENRADIO SETTINGS of the fixture should be set to UNLINK, then it could reconnected by a new fixture or transmitter.
② Connect the fixture or CRMX wireless DMX transmitter set to TRANSMITTER MODE with the fixture needs to receive CRMX wireless DMX signals for remote
control.
UNLINK
MENU CH: 512
PRESS “MENU” TO RETURN
DO YOU WANT TO UNLINK?
NO YES
MENU CH: 512
PRESS “MENU” TO RETURN
DO YOU WANT TO UNLINK?
NO YES
MENU CH: 512
PRESS “MENU” TO RETURN

16
Operation Instructions
1. Make sure the power switch is in the "off" position, then connect the fixture to the power supply with power cable. Then turn on the power switch, if the indicator is
normally on, the screen will first display “NANLUX”, that means the power is active.
2. CCT Key: Press CCT Key to enter the operation interface of CCT Mode.
DIM
100%
CCT
5600K
CCT MODE CH: 512
Color
Temperature
Unlock/Lock Status
Power Supply
Display
Channel
Mode
Brightness
DIM
100%
CCT
5600K
CCT MODE CH: 512

17
NOTE: In other modes, the DIM range is same as in CCT Mode. When the fixture function is unlock, in any mode, press the “Lower knob”, the light is off, the DIM
percentage on the display is 0% , press again, the fixture restores the previous status, press continuously to switch brightness betweeen on and off.
NOTE: Press "Upper knob" to quickly adjust CCT in sequence: 2700K, 3200K, 4300K, 5600K, 6500K, 7500K.
① DIM setting: rotate “Lower knob”, clockwise to increase brightness while counterclockwise to reduce brightness, the display shows the percentage of brightness,
the DIM range is from 0%-100%.
② CCT setting: rotate “Upper knob", clockwise to increase the color temperature while counterclockwise to reduce the color temperature,
the display shows the value of CCT, the CCT range is from 2700K-7500K.
DIM
100%
CCT
5600K
CCT MODE CH: 512
0%
.
.
.
100%
DIM
100%
CCT
5600K
CCT MODE CH: 512
2700K
.
.
.
7500K

18
· TK-140B and TK-280B has built-in special effects: CCT LOOP, INT LOOP, FLASH, PULSE, STORM AUTO, STORM MANUAL, TV, PAPARAZZI, CANDLE/FIRE,
BAD BULB, FIREWORK, EXPLOSION AUTO, EXPLOSION MANUAL, WELDING.
Rotate "Lower knob" to select the desired special effect.
3. EFFECT Key: Press EFFECT Key to enter the operation interface of EFFECT Mode.
DIM: 100%
CCT: 2700K - 7500K
SPEED: 8s
EFFECT: CCT LOOP
EFFECT MODE CH: 512
DIM: 100%
CCT: 2700K - 7500K
SPEED: 8s
EFFECT: CCT LOOP
EFFECT MODE CH: 512
DIM: 0% - 100%
CCT: 5600K
SPEED: 50
PAUSE: OFF
EFFECT: WELDING
EFFECT MODE CH: 512
CCT LOOP
.
.
.
WELDING