NAPCO Gemini GEM-P3200 Installation manual

R


HARDWIRE WIRELESS


WI818B 5/99© Napco 1999
Quick Start:
1. Refer to the wiring diagram, connect siren, aux. power,
aux. output, remote bus, earth ground, zone and
telephone wiring. NOTE: See Installation Instructions (WI817).
2. Connect AC power first and then the battery.
3. Configure the keypad (see page 44).
4. Access the Easy Menu Driven (Dealer Program) Mode:
Press


Press

Until “   
  
” (GEM-RP1CAe2) or
“   
  
” (GEM-RP2ASe2)
appears on LCD screen.
Press

To Enter Dealer Program Mode (see page 6).
Master Security Code
(printed on microprocessor can)
GEM-RP1CA/RP1CAe/RP1CAe2 Keypad
R
  

ARMED
STATUS































NEXT/YES
PRIOR/NO
AREA
     
    
  
  
GEM-RP2AS/RP2ASe/RP2ASe2 Keypad
R
  
ARMED
STATUS
 
 
 
 












NEXT/YES
PRIOR/NO
AREA

 
 


NAPCO Security Systems, Inc.
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, call toll free: [phone]
For direct line to Technical Service, call toll free: [phone]
Internet: http://www.napcosecurity.com
CHANGES FROM PREVIOUS EDITION
The following changes have been made to this manual (WI818B) since the last edition (WI818A).
✔ Manual format has been revised.
✔ Programming options “RF Transmitters” and “Key fob Transmitters” have been removed from Direct
Address Program Mode and are selected only in Easy Menu Driven Program Mode.
✔ Programming option “Veri-phone Zones trip Fire Output” (Page 34, Address 2421) has been added.
✔ Programming option “Telco Answering Service Overide” (Page 34, Address 2421) has been added.
✔ Programming option “Keyfob Zone Assignment” (Page 10 & 15) has been added.
✔ Programming option “RF Receiver Tamper” (Page 26, Address 0896) has been added.
✔ Programming option “Access on Aux. Output” (Page 10 & 15) has been added.
✔ Programming option “Disable System Trouble Audible at Keypad” (Page 36, Address 2420) has been added.
✔ Programming option “Disable Exit/Entry Urgency Tone at Keypad” (Page 36, Address 2422) has been added.
✔ Programming option “Enable Burg. Ouput on Telco fail only when Armed” (Page 36, Address 2422) has been
added.
✔ Programming option “Enable Burg. Output for Keyfob Chirp” (page 36, Address 2422) has been added.
✔ Programming option “Enable Auxiliary Ouput Chirp on Keyfob Arm/Disarm” has been renamed to “Enable Ouput
Chirp on Keyfob Arm/Disarm” (Page 36, Address 2421).
✔ Programming option Relay Event ID Code “Area 1 Keypad Tamper” has been renamed to “Keypad Tamper”
(Page 41).
✔ Programming option Relay Event ID Code “Area 2 Keypad Tamper” has been deleted (Page 41).
NOTE: For specific information on any of the listed programming options refer to the Glossary in the GEM-P3200
Installation Instructions (WI817).

NAPCO Security Systems GEM-P3200 Programming Instructions
WI818B 5/99  Page 3
SYSTEM PROGRAMMING OPTIONS.............................4
Introduction ..................................................................4
Downloadin
g
from a Computer ....................................4
EASY MENU DRIVEN PROGRAM MODE.......................5
Dealer Pro
g
ram - Preliminary Information....................5
Accessin
g
Dealer Pro
g
ram Mode ................................5
Customizin
g
a Default Pro
g
ram...................................5
GEM-RP1CAe2 KEYPAD............................................6
Number of Zones & Keypads per Area...................6
Local or Central Station Reportin
g
System.............6
Central Station Receiver 1 Tel. Number.................6
Central Station Receiver 1 Account Number..........6
Central Station Receiver 1 Format..........................6
Enter User Codes ...................................................7
Enter Zone Descriptions .........................................8
RF Transmitter Points.............................................9
Key Fob Transmitters .............................................10
Enter Date...............................................................10
Enter Time .............................................................10
GEM-RP2ASe2 KEYPAD ............................................11
Number of Zones & Keypads per Area ..................11
Local or Central Station Reportin
g
System.............11
Central Station Receiver 1 Tel. Number.................11
Central Station Receiver 1 Account Number..........12
Central Station Receiver 1 Format..........................12
Enter User Codes ...................................................12
RF Transmitter Points.............................................14
Key Fob Transmitters .............................................15
Enter Date...............................................................15
Enter Time ..............................................................15
DIRECT ADDRESS PROGRAM MODE...........................16
Keypad Pro
g
rammin
g
Overview ..................................16
Accessin
g
Direct Address Pro
g
ram Mode...................16
What You See on the Keypad......................................16
Direct Address Pro
g
ram Mode Keypad Commands....17
Pro
g
rammin
g
Overview................................................18
Direct Address Pro
g
rammin
g
Example...................19
PROGRAMMING OPTIONS & WORKSHEETS ..............20
System Delays (Addr 0000-0002, 2402, 2406 & 2414)21
System Delays (Addr 2407, 2408 & 4088)...................21
System Delays (Addr 2400, 2401, 2403-2405 & 4083)22
Keypad System Codes (Addr 0490, 0495 & 0500)......22
User Code Options (Addr 0010-0169).........................23
CS Receiver Opt. (Addr 0520, 0521, 0525, 0526, 0550,
0551, 0575 & 0576)......................................................25
CS Receiver Tel. Numbers (Addr 0527-0546, 0552-0571,
0577-0596)...................................................................26
Download/Callback Options (Addr 4089, 0600-0619,
0625-0647, 1022 & 1023) ............................................26
CS Subscriber ID Numbers (Addr 0650-0857) ............27
CS Reportin
g
Codes (Addr 0860-0869).......................27
CS Reportin
g
Codes (Addr 0870-0904).......................28
CS Area & System Reportin
g
Opt. (Addr 1024-1027) .28
CS Zone Reportin
g
Codes (Addr 0910-0941)..............29
CS User Reportin
g
Codes (Addr 1030-1081)..............30
Global System Trbl. Reportin
g
Opt. (Addr 1082-1116) 31
Area System Trbl. Reportin
g
Opt. (Addr 1120-1137)...32
Zones 1-16 Options (Addr 1200-1376)........................33
Zones 17-32 Options (Addr 1402-1576)......................34
System Options (Addr 2415-2419) ..............................35
System Options (Addr 2420-2422 & 4084)..................36
Keypad Options (Addr 2425-2531) ..............................37
EZM Group Options (Addr 2600-2627)........................38
Area Armin
g
Options (Addr 2650 & 2651) ...................38
Area Output Control Options (Addr 2700-2733) ..........39
Remote Access Lo
gg
in
g
(Addr 3184)..........................39
Number of Relay Board Modules (Addr 3777).............39
Ext. Relay Control (Addr 3778-3801 & 2800-2895) .....40
RF Rcvrs. & Sup. Timers (Addr 3776 & 3760-3775)....42
System Reset Features (Addr 4090-4093)..................43
USER PROGRAM MODE.................................................44
Preliminary Information................................................44
Accessin
g
User Pro
g
ram Mode...................................44
User Codes..................................................................44
Zone Descriptions........................................................45
KEYPAD CONFIGURATION MODE................................46
Keypad Installation.......................................................46
Confi
g
urin
g
the Keypads..............................................46
GEM-P3200 EASY MENU PROG. WORKSHEETS ........49
KEYPAD PROGRAMMING MODES................................52
PROGRAMMING OPTIONS INDEX.................................57
GEM-P3200 WIRING DIAGRAM......................................64

Refer to accompanying GEM-P3200 Installation Instructions (WI817) for installation information.
NOTE: THESE PROGRAMMING INSTRUCTIONS ARE INTENDED AND WRITTEN FOR THE PROFESSIONAL INSTALLER HAVING SUITABLE
EXPERIENCE AND INSTALLATION EQUIPMENT. THE UNIT IS DESIGNED TO BE PROGRAMMED USING AN IBM-COMPATIBLE COMPUTER
WITH NAPCO PCD3000 SOFTWARE. AFTER PROGRAMMING, BE SURE TO RUN THE PCD3000 ERROR-CHECK UTILITY TO GUARD
AGAINST PROGRAMMING CONFLICTS FOR THE TYPE OF SERVICE SELECTED FOR THE INSTALLATION.

GEM-P3200 Programming Instructions NAPCO Security Systems
WI818B 5/99
Page 4


The GEM-P3200 control panel may be programmed by various means, each of which will be covered in detail in the
sections that follow. Keypad displays shown first are for a GEM-RP1CA/RP1CAe/RP1CAe2, the recommended keypad for
programming, then for the GEM-RP2ASe2. The GEM-RP2ASe2 keypad functions similarly; however, because of its
reduced display capabilities, messages are abbreviated and will scroll through two or more screens. Zone descriptions
cannot be programmed using a GEM-RP2AS/RP2ASe/RP2ASe2 keypad.
✔ Downloading From a Computer. This is the preferred method. The panel may be downloaded from (or uploaded
to) an IBM PC-compatible computer, with a 386 (or higher) microprocessor, either locally or remotely. Napco's
PCD3000 Quickloader software, Version Update 3.26 or later features context-sensitive help screens as well as an
error-checking utility that prevents programming of incompatible or conflicting data to ensure proper panel operation.
✔ Easy Menu Driven Program (Dealer Program) Mode - Keypad Programming. The Easy Menu Driven Program
Mode allows keypad programming of number of zones in area 1, number of fire zones (both 4-wire and 2-wire), central
station reporting, number of entry/exit zones, number of interior zones, number of keypads in area 1, central station
telephone number, central station account number, central station receiver format, user codes, rf transmitter points, rf
key fob transmitters and zone descriptions. For new panels, a custom default program may be created at the keypad.
A menu-driven utility prompts the installer to configure the system. Further detailed customization is done in the Direct
Address Program Mode.
✔ Direct Address (Dealer Program) Program Mode - Keypad Programming. The Direct Address Program Mode
is an extension of the Dealer Program Mode wherein data is entered at the keypad by location. This mode is accessed
from the Easy Menu Driven Program Mode by pressing the

button at any time.
✔ User Program Mode - Keypad programming. The User Program Mode is intended for authorized users and is
limited to keypad programming of User Codes and Zone Descriptions.

The control-panel program may be downloaded from the
computer by either of the following methods.
Local Downloading
(Note: This procedure should be used after to installation, after peripheral devices are connected.)
For a direct high-speed data transfer to the control panel from a desktop computer, connect the download jack (J1) on the
panel to the LOCAL jack (J3) on the Napco PCI2000/3000 computer interface using the supplied 6-conductor cable.
(Refer to PCI2000/3000 Installation Instructions WI443 for wiring diagram and procedures.)
Similarly, a high-speed local download may be made in the field using a notebook or laptop computer. Connect J1 on the
control panel to a Napco PCI-MINI computer interface using the 6-conductor cable supplied. (Refer to PCI-MINI
Installation Instructions WI767.)
Remote Downloading
(Also see PCI2000/3000 Installation Instructions WI443.)
Function Mode. During this procedure, voice contact will be lost, therefore both the installer and the computer operator
should be familiar with the operation. When a steady high-pitched tone is heard at the site phone, access the “ 
 ” Function (see Keypad Programming Modes), then press the button or the YES (

) button; the site
phone will go dead. Hang up the phone and wait for a call from the central station confirming a successful download.
Callback Method. An installed, unattended panel may be programmed or reprogrammed remotely using the Callback-
Method Download feature of the PCD3000 software. Remote downloading requires a modem compatible with the
PCI2000/3000. Upon answering the call from the computer, the panel will verify the Download Security Code and, if
confirmed, will establish a connection. If a Callback Number is programmed into the panel, the panel will automatically
disconnect and call the computer at this number before establishing a connection. The panel can support two Callback
Numbers to allow downloads from two different offices.

NAPCO Security Systems GEM-P3200 Programming Instructions
WI818B 5/99  Page 5


Only Keypad #1 may be used for both dealer and user programming, however this keypad may be located in any area.
The Master Security Code is
printed on the panel’s microprocessor can
. Use this code to enter the Dealer Program
Mode to program a custom Dealer Security Code. Record the number, then remove the code label to prevent
unauthorized access to the panel. If you forget your Dealer Security Code, use the Master Security Code to enter
programming.
After entering codes or data, press the save button. Data will not be stored into memory unless it is pressed.
If the keypad is in the Program Mode and no activity is detected for longer than 4 minutes, a steady tone will sound.
Silence the sounder by the

button to continue, or by pressing the

button to exit.
A panel that has been COLD STARTED (Address Location 4093) performs identically to a new panel.
When programming a Two Area System, Direct Address Programming Mode must be used to complete the program.
If a GEM-RP2AS/RP2ASe/RP2ASe2 is used, configure address jumpers as Keypad #1 (see Configuring the GEM-
RP2ASe2 Keypad.). Use the

button to manually scroll through each selected option and at the end of each
programming line.


For any new panel, you can design a default program that will best suit your application. Using this procedure, you will configure the
panel for:
This procedure will automatically set up system keypads, EZMs, wireless transmitters, etc. After your basic default program has been
loaded, you may alter it as necessary in the Direct Address Program Mode in the conventional manner.
KEYPAD #1: For ease of programming, it is recommended that a GEM-RP1CA/RP1CAe/RP1CAe2 be used as Keypad
#1. (Regardless of which keypad is selected, all
new
keypads are configured as Keypad #1 out of the box.)
✔ Number of Zones per area (in multiples of 4)
✔ Number of Keypads per area
✔ Type of System (Local or CS Reporting)
✔ CS Reporting Features (Telephone Number, Account Number &
Receiver Format)
✔ User Codes
✔ Zone Descriptions
✔ RF Transmitter Information (Zone & RF ID number)
✔ Date and Time
NEW PANELS: The custom default program may be created for new panels only. Once the panel has been programmed by any
means, the number of areas, zones and keypads will be suppressed and cannot be changed. Should it be necessary to create a new
custom default program, (a) from the Dealer Program Mode, press the

button to enter the Direct Address Program Mode; (b)
access Location 4091 (Clear Program); (c) press the

button and start over.
Accessing Dealer Program Mode
1. Press


2. Press

Until
“    ”
(GEM-RP1CAe2) or
“    ” (GEM-RP2ASe2)
appears on LCD screen.
3. Press

To Enter Dealer Program Mode
4. Press

To Exit Dealer Program Mode when finished
Master Security Code
(on microshield)
R



MASTER SECURITY CODE
# - # - # - # - # - #
R
     

ARMED
STATUS


























NEXT/Y ES
PRIOR/ NO
AREA


  
  

GEM-P3200 Programming Instructions NAPCO Security Systems
WI818B 5/99
Page 6
GEM-RP1CAe Keypad: Zones/Keypads per Area, CS Reporting, CS Telephone No., CS Acct. No. & CS Format
A. GEM-RP1CA/RP1CAe/RP1CAe2 Keypad
To create your customized default program using a GEM-RP1CA/RP1CAe/RP1CAe2 keypad, enter the
following parameters and record your information on the
Easy Menu Pro
g
rammin
g
Worksheet
.
Number of Zones & Keypads per Area
(Appears for New Panel Only)
Use the

button to set cursor and the

button to select data
entry. For Area 1, enter (a) the number of zones (8–24, in multiples of 4),
then (b) the number of keypads (1–4). For Area 2 (if used), enter (a) the
number of zones (0–24, in multiples of 4), then (b) the number of keypads
(0–4). Press to save. Press NEXT (

) button to proceed.
Notes: (1) The GEM-P3200 is limited to a combined maximum of 32 zones and 7 keypads. However, in this section a maximum of 24 zones and 4
keypads are allowed. (2) The first zone of Area 1 (and Area 2, if selected) will automatically be programmed as Exit/Entry Zones with an entry delay of
30 seconds and an exit delay of 60 seconds. The second zone will be programmed for Exit/Entry Follower. (3) In a single-area system, Zone 8 will be
programmed as a 2-Wire Fire Zone. In a two-area system, Zones 7 and 8 will be programmed as 2-Wire Fire Zones and will be common to both areas
(set Jumper JP7 to configure the circuit board). (4) All 32 zones and 7 keypads are programmed in Direct Address Program Mode. See Zone and
Keypad Options.
Local or Central Station Reporting System
(Appears for New Panel Only)
Press YES (

) button for all zones to report; press NO (

) button
for no zones to report (LOCAL SYSTEM).
Central Station Receiver 1 Telephone Number
Using number buttons, enter telephone number of up to 16 digits including-
prefix letters, if necessary, for receiver 1. Use number buttons

through

for digits 1–9; press the

button for a zero and

through

for letters B–F, respectively. NOTE:
Pre-Dial Delay = “D”; Dial-Tone Detection = “E”. Pressing the

button will produce a blank space (•). Press to
save. Press NEXT (

) button to proceed. NOTE: Central Station Receiver 2 and 3 Telephone Numbers can only be
entered in Direct Address Programming. See CS Receiver Options.
Central Station Receiver 1 Account Number
Enter an account number of up to four digits. Use number buttons

through

for digits 1–9. NOTE: Press the

button for a zero
and press

button for a blank space (•). Press to save . Press
NEXT (

) button to proceed. NOTE: Central Station Receiver 2 and 3
Account Numbers can only be entered in Direct Address Programming. See CS Reporting Options.
Central Station Receiver 1 Format
From the table below, enter the central station's receiver format. Use number
buttons

through

. NOTE: Press the

button for a
zero and press

for a blank space (•). Press

through

for letters B–E, respectively.
Press to save. Press NEXT (

) button to proceed.
(Press YES or NO)


R
  

ARMED
STATUS














 

















NEXT/YES
PRIOR/NO
AREA

    
  
  
(Direct Entry)


(Entry Scrolls)


(Direct Entry)

(Direct Entry)

  
DATA
ENTRY CS RECEIVER 1 FORMAT
blank(•) Ademco Slow, Silent Knight Slow
1 Sescoa, Vertex, DCI, Franklin Fast
2 Radionics Fast
3 Silent Knight Fast
4 Radionics, DCI, Franklin Slow
5 Universal High Speed
8 Radionics BFSK
DATA
ENTRY CS RECEIVER 1 FORMAT
9 FBI 4/3/1
0 Radionics Modem 2
BSIA
C Ademco Point ID
D Ademco Express
E Pager
NOTE: Modem IIe is available only in Direct
Address Programming. Central Station Re-
ceiver 2 and 3 Formats can only be entered in
Direct Address Programming. See CS Re-
ceiver Options.

NAPCO Security Systems GEM-P3200 Programming Instructions
WI818B 5/99  Page 7
Enter User Codes
(Press the
(

)
button to set cursor.)
For default program, enter up to 16 User Codes: up to 8 for Area 1 (Users
01–08) and up to 8 for Area 2 (Users 09–16), with an Authority Level and
Access Control Options (if necessary) for each code, as follows. Note: Up to
32 users are available using Direct Address Program Mode.
Press the (

) button to set the cursor to the User Number. Use the
number buttons

through

to enter the User Number.
Press the (

) button once to set the cursor to the User Code. Use the number buttons

through

to
enter a code of up to 6 digits. Enter up to 6 digits (4 digits is recommended) in the first six boxes from left to right for
each user code. Valid entries are: 0-9. Note: Press the

button for a zero. No blank spaces in between; leave
blank (•) any trailing boxes. If an “Ambush Code” (Address 0495) is entered,
do not
program the first two digits of ANY
User Code as the same digits entered for the “Ambush Code”.
If the programmed code is less than 6 digits, press the

button once to set the cursor to the OPTION/LEVEL.
Refer to the tables below for the available User Option and User Level data entries. Enter the user options data in the
left digit. Enter the level data (with arming options, if any, added) in the right digit. Note: For entries greater than 9,
press the

buttons through the

buttons for B through F, respectively.
For Keypad Access Control, press the

button once again to program applicable keypads. Refer to the tables
below, use the number buttons to enter the data for Keypad 1–4 in the right digit; and the data for Keypad 5–8 data in
the left digit. (Press the

buttons for blank.)
GEM-RP1CAe/RP1CAe2 Keypad: User Codes
User# User Code Option Access
/Level Control
!"!"
#
USER OPTIONS
USER CODE
(UP TO 6 DIGITS) USER
OPTION USER LEVEL ACCESS CONTROL KEYPADS
123456
DATA
ENTRIES AUTHORITY LEVEL CODE TYPE
blank (•) NONE ARM/DISARM
1 LEVEL 1 ARM/DISARM
2 LEVEL 2 ARM/DISARM
3 LEVEL 3 ARM/DISARM
4 NONE ARM ONLY
5 LEVEL 1 ARM ONLY
6 LEVEL 2 ARM ONLY
7 LEVEL 3 ARM ONLY
8 NONE SERVICE
9 LEVEL 1 SERVICE
0 LEVEL 2 SERVICE
B LEVEL 3 SERVICE
Note: “Y” indicates option is enabled.
USER OPTIONS
DATA
ENTRIES BLOCKED VIEW USER PROGRAM BYPASS OVERVIEW
blank (•) DISABLED
1Y
2Y
3Y Y
4Y
5Y Y
6YY
7Y Y Y
8Y
9Y Y
0Y Y
BY Y Y
CYY
DY Y Y
EYYY
FY Y Y Y
Note: “Y” indicates option is
enabled.
ACCESS CONTROL KEYPADS
DATA
ENTRIES K.P. 5 K.P. 6 K.P. 7
blank (•) NONE
1Y
2Y
3YY
4Y
5Y Y
6YY
7YYY
Note: “Y” indicates option is enabled.
ACCESS CONTROL KEYPADS
DATA
ENTRIES K.P. 1 K.P. 2 K.P. 3 K.P. 4
blank (•) NONE
1Y
2Y
3YY
4Y
5Y Y
6YY
7YYY
8Y
9Y Y
0YY
BYY Y
CYY
DY YY
EYYY
FYYYY
Note: Users are assigned to areas in “Enable User Code by Area” (Address 2500-2531) in Direct Address Programming.
Example:
Enter a code of “123456” as
“123456”.

GEM-P3200 Programming Instructions NAPCO Security Systems
WI818B 5/99
Page 8
Press to save each code.
To proceed to the next User Code, set the cursor to the User Number and change it using the number buttons. Program a
new User Code as previously described. Press NEXT (

) button to proceed.
Enter Zone Descriptions
Press the

and

buttons to place the cursor; press the

and

buttons to select the character. For each zone, enter a descrip-
tion of up to two lines. Press to save each description. To proceed to the
next description, place the cursor under the Zone Number (e.g. “01”) and
change the Zone Number using the

and

buttons. Program a new description as above.
NOTE: Zone Descriptions can only be entered through the
GEM-RP1CA/RP1CAe/RP1CAe2 Keypad or by using the
Napco Quickloader Software.
Press NEXT (

) button to proceed.
Example:
Program a code of “2222” for user 02, with User Option of “User Program”, User “Level 3” and Access Control Option
“Keypad No. 1”. Enter “2222” for a user code, “2 3” for user option and “blank(•) 1” for access control option.
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above
and press to save. Similarly, to cancel a code, blank out each number of the code press to save to save.
USER AUTHORITY LEVEL
KEYPAD DISPLAY FUNCTION MENU
FUNCTION LEVEL*
DISPLAY ZN FAULTS 1
DISPLAY ZN BYPASSED 1
DISPLAY ZN DIRECTORY 1
ACTIVATE BELL TEST 1
DISPLAY PHONE #’S 1
DISPLAY SYS TRBL 1
DISPLAY FIRE ALARM 1
DISPLAY FIRE TRBL 1
DISPLAY OP/CL 3
ACTIVATE OVERVIEW 3**
ACTIVATE CHIME 1
ACTIVATE WATCH 2
RESET SYSTEM TRBL 3
RESET SENSOR MSG 3
START EXIT TIME 1
FAULT FIND ***
ACTIVATE LOCATE ***
EZM ZONE FIND ***
ACTIVATE DIALER TEST 3
DISPLAY ALARM LOG 3
DISPLAY TOTAL LOG 3
DISPLAY FIRE LOG 3
DISPLAY OP/CL LOG 3
DISPLAY SYSTEM LOG 3
AUTOARM IN 1-4HRS 2
DISPLAY AUTARM SCHD 3
ACTIVATE PROGRAM 3**
ACTIVATE DOWNLOAD 3
DISPLY RF XMITTER STAT 1
RELAY CONTROL 1
NOTES:
* Minimum Level required to access function
** Level-3 Code with appriopriate user option
*** Requires Dealer Code
Related User Options:“Ambush Code” (Address 0495), “Panel Access Code” (Address
0490), “Dealer Security Code” (Address 0500) & “Enable User Code by Area” (Address
2500-2531).
USER OPTIONS
OPTIONS EXPLANATION
Disabled User Code not active in this area.
Blocked View Allows User Code to block another code from being viewed by another user.
An unblocked code cannot view a blocked code, but a blocked code can view
all codes. The master user code and the dealer program code can view all
codes.
User Program User Program Option is enabled for Keypad 1 only, wherever it is connected
(Area 1 or Area 2). If enabled, Level 3 must also be enabled.
Bypass Allows User Code to bypass zones.
Overview This option, along with Level 3 Authorization, enables selection of
OVERVIEW mode at a keypad. This Mode provides a system status display of
all areas at a glance.
Arm Only Prevents User Code from disarming this area.
Service A Service Code has restricted arm/disarm rights; if an area is armed with a
Service Code, a “
 
 
” appears on the GEM-RP1CAe2 keypad (a “


”
on the GEM-RP2ASe2 keypad) and the area can be disarmed with any valid
User Code, including a Service Code. If the area is armed with OTHER than a
Service Code, it CANNOT be disarmed with a Service Code. This is typically
used to allow tradesmen access to premises under control of the owner.
Access This is normally used to activate a door striker while an area is disarmed.
Also program “Access Control on Aux. Output” (Address 2418) and “Aux.
Output Access Control Timeout” (Address 2402).
(Direct Entry)


GEM-RP1CAe/RP1CAe2 Keypad: Zone Descriptions

NAPCO Security Systems GEM-P3200 Programming Instructions
WI818B 5/99  Page 9
RF Transmitter Points
(Press the
(

)
button to set cursor.)
(For wireless systems only. Also see Quick Method, which follows)
For each transmitter (key fob transmitters also), enter the zone number
(01–32) to which the transmitter will be mapped, the 6-digit RF ID #:1-digit
checksum number printed on the transmitter and box, the point number
(1–4);
enter “9” for unsupervised
(all points). NOTE: When programming the
ID Code number, “A” =

; “B” =

; “C” =

; “D” =

; “E” =

;
“F” =

. Press to save. Press NEXT (

) button to proceed.
Quick Method.
If a receiver is already installed in the panel, Napco transmit-
ter wireless points can be programmed automatically (“enrolled”) using the
following procedure. NOTE: The transmitter point will be enrolled only if the
signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be mapped.
2. Press the

button to enter the Enroll Mode. The red and green LEDs
on the keypad will flash and the window will display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-TRANS2 or
GEM-TRANS4 only).
4. Install the transmitter battery. The keypad will beep to indicate that the point has been successfully enrolled. Multi-point
transmitters can be mapped to successive zones simultaneously (Example 1) or to selected zones point by point (Example
2).
Example 1. A 4-point transmitter has the RF ID number 410078:1. Map the first three points to Zones 11–13, respectively.
1. Enter the Enroll mode as described in step 2 above.
2. Enter Zone “11”.
3. Open the loops of points 1, 2 and 3.
4. Install the transmitter battery. The keypad will beep 3 times to indicate that three points have been programmed.
Transmitter 410078:1, point 1 will be mapped to Zone 11.
Transmitter 410078:1, point 2 will be mapped to Zone 12.
Transmitter 410078:1, point 3 will be mapped to Zone 13.
The keypad will now display Zone 13, the last zone enrolled.
Example 2. A 2-point transmitter has the RF ID number 287613:1. Map point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone “06”.
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that one point has been programmed. (Transmitter 287613:1,
point 1 will be mapped to Zone 6.)
5. Enter Zone “09”.
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad will beep once to indicate that one point has been
programmed. (Transmitter 287613:1, point 2 is mapped to Zone 9.)
Zone # Xmitter Check Point
Mapped to ID Sum #
$ %
"&"
$ %
"&"
$ %
"&""
KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wireless panic buttons on one
alarm system, each reporting to a central station, a pager or having a description on the keypad that describes the person
holding the key fob, the location where the person holding the key fob is stationed, or the special purpose of the key fob
button being depressed.
See the next pa
g
e on Key fob Zone Assi
g
nment.
GEM-RP1CAe/RP1CAe2 Keypad: RF Transmitter Points

GEM-P3200 Programming Instructions NAPCO Security Systems
WI818B 5/99
Page 10 Key Fob Transmitters
(Press the
(

)
button to set cursor.)
Keyfobs can be programmed as “Arm/Disarm” devices using their buttons
(refer to WI752). For each Key Fob Transmitter, enter:
the Key Fob Transmitter number (01–08).
area number to which transmitter is assigned (1 or 2); enter 0 to disable
keyfob.
the 6-digit RF ID # printed on the transmitter (enter all numbers and/or letters, including
leading “0”s, if any).
1-digit checksum number printed on the transmitter (enter all numbersand/or letters,
including leading “0”s, if any).
Aux-1 Option (see key fob aux 1 & aux 2 options).
Aux-2 Option (see key fob aux 1 & aux 2 options).
Note: If the Key Fob is converted for Two Button “Emergency Use” (by cutting an internal
jumper), both top or bottom buttons must be depressed to activate an alarm. In this case, the
Aux-1 and Aux-2 cannot be programmed. Press to save. Press NEXT (

) button to proceed.
Key Fob Zone Assignment
(refer to display as shown on the previous pa
g
e: press the
(

)
button to
g
o backwards.)
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button = point 2; A1 = point
3; A2 = point 4. Up to 32 key fobs (using 1 button) or 16 key fobs (using 2 buttons) or 8 key fobs (using all 4 buttons) or any
combination up to a maximum of 32 controlled zones can be assigned, providing multiple wireless panic buttons on a
system, each reporting to the Central Station or a pager and/or annunciating on a keypad the key fob zone number with
description/location.
To assi
g
n a key fob to a zone:
program the keyfob as you would a transmitter, entering the keyfob's
ID code, check sum and point number at the appropriate zone. The “Quick Method” is not allowed. The zone may be
hardwired to a sensor as well as assigned to a key fob (either one will activate the zone alarm output). NOTE: If assigning
a key fob to a zone, the “ON/OFF” buttons on the key fob will no longer arm/disarm the system. The key fob is converted
to a “panic only” device.
Enter Date
(Press the
(

)
button to set cursor.)
Enter the current date in the format MM/DD/YY, where MM = the month
(01–12); DD=the day (01–31); and YY=the year. Press to save. Press
NEXT (

) button to proceed.
Enter Time
(Press the
(

)
button to set cursor.)
Enter the current time in the format HH:MMA/P, where HH=hours (01–12);
MM=minutes (00–59). Select Am or Pm by pressing any number button, then
press once again to save.
CLEAR PROGRAM: Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode,
press the

button to enter the Address Program Mode; (b) access Location 4091 (Clear Program); (c) press and
start over.
KF Area Xmitter Check Aux
# ID Sum 1&2
$ %
"&
EXIT DEALER PROGRAM MODE: This completes the custom default program. Press the

button to enter the
Direct Address Program Mode for further programming or press the

button once again to end all programming and
resume normal keypad operation.
DATA
ENTRY AUX 1/AUX 2 OPTIONS
0 None
1 Relay Group 1 Toggle
2 Relay Group 2 Toggle
9Panic
A Auxiliary
B Instant
C Aux. Output Toggle
D Access on Aux. Output
(Direct Entry)
##
#
(Direct Entry)
&
 
NOTE: Key fobs 1-8 report as Users 25-32.
GEM-RP1CAe/RP1CAe2 Keypad: Keyfob Transmitters, Date, Time & Exit Dealer Program Mode

NAPCO Security Systems GEM-P3200 Programming Instructions
WI818B 5/99  Page 11
A. GEM-RP2AS/RP2ASe/RP2ASe2 Keypad
Enter the Master Security Code (printed on microprocessor can) for a new panel or enter your custom
Dealer Program Code if programmed. Press NO (

) repeatedly until “'” is displayed.
NOTE: If you pass “'”, you can scroll back by pressing the

button. Press YES
(

) to enter the Dealer Program Mode. This keypad displays messages in multiple segments. Press
the

button to scroll through each segment.
Number of Zones & Keypads per Area
(Appears for New Panel Only)
Press the

button to scroll screens. Use the

button to set cursor
and the

button to select data entry. For Area 1, enter (a) the number
of zones (8–24, in multiples of 4), then (b) the number of keypads (1–4). For
Area 2 (if used), enter (a) the number of zones (0–24, in multiples of 4), then
(b) the number of keypads (0–4). Press to save. Press NEXT (

)
button to proceed.
Note: (1) The GEM-P3200 is limited to a combined maximum of 32 zones
and 7 keypads. (2) The first zone of Area 1 (and Area 2, if selected) will
automatically be programmed as Exit/Entry Zones with an entry delay of 30
seconds and an exit delay of 60 seconds. The second zone will be pro-
grammed for Exit/Entry Follower. (3) In a single-area system, Zone 8 will be
programmed as a 2-Wire Fire Zone. In a two-area system, Zones 7 and 8 will
be programmed as 2-Wire Fire Zones and will be common to both areas (set
Jumper JP7 to configure the circuit board).
Local or Central Station Reporting System
(Appears for New Panel Only)
Press the

button to scroll screens. Press YES (

) button for all
zones to report; press NO (

) button for no zones to report (LOCAL
SYSTEM).
Central Station Receiver 1 Telephone Number
Press the

button to scroll screens. Using number buttons, enter
telephone number of up to 16 digits including prefix letters, if necessary, for
receiver 1. Use number buttons

through

for digits 1–9; press
the

button for a zero and

through

for letters B–F, respectively. NOTE: Pre-Dial Delay = “D”; Dial-Tone Detec-
tion = “E”. Pressing the

button will produce a blank space (•).
Press to save. Press NEXT (

) button to proceed.
NOTE: The GEM-RP2AS/RP2ASe/RP2ASe2 keypad provides a maximum
of 10 digits in this mode. To program additional digits, go to the Direct
Address Program Mode and continue from Location 0537. Central Station
Receiver 2 and 3 Telephone Numbers can only be entered in Direct Address
Programming. See CS Receiver Options.
R
  
ARMED
STATUS
 
 
 
 












NEXT/YES
PRIOR/NO
AREA

 
 

(Direct Entry)




(Press YES or NO)



(Direct Entry)



GEM-RP2AS/RP2ASe Keypads: Zones & Keypads per Area, CS Reporting, CS Tel. No. & CS Acct. No.

GEM-P3200 Programming Instructions NAPCO Security Systems
WI818B 5/99
Page 12 Central Station Receiver 1 Account Number
Press the

button to scroll screens. Enter an account number of up to
four digits. Use number buttons

through

for digits 1–9. NOTE:
Press the

button for a zero and press

button for a blank
space (•). Press to save . Press NEXT (

) button to proceed.
NOTE: Central Station Receiver 2 and 3 Account Numbers can only be
entered in Direct Address Programming. See CS Reporting Options.
Central Station Receiver 1 Format
Press the

button to scroll screens. From the table below, enter the
central station's receiver format. Use number buttons

through

.
NOTE: Press the

button for a zero and press

for a
blank space (•). Press

through

for letters B–E,
respectively.
Press to save. Press NEXT (

) button to proceed.
Enter User Codes
Press the

button to scroll screens. For default program, enter up to 16
User Codes: up to 8 for Area 1 (Users 01–08) and up to 8 for Area 2 (Users
09–16), with an Authority Level and Access Control Options (if necessary) for
each code, as follows. Note: Up to 32 users are available using Direct
Address Program Mode.
Press the (

) button to set the cursor to the User Number. Use the
number buttons

through

to enter the User Number.
Press the (

) button once to set the cursor to the User Code. Use
the number buttons

through

to enter a code of up to 6 digits.
Enter up to 6 digits (4 digits is recommended) in the first six boxes from left
to right for each user code. Valid entries are: 0-9. Note: Press the

button for a zero. No blank spaces in between; leave blank (•) any trailing
boxes. If an “Ambush Code” (Address 0495) is entered,
do not
program the
first two digits of ANY User Code as the same digits entered for the “Ambush
Code”.
If the programmed code was less than 6 digits, press the

button once to set the cursor to the OPTION/LEVEL.
Refer to the tables shown for the available data entries. Enter the options data in the left digit. Enter the level data (with
arming options, if any, added) in the right digit. Note: For entries greater than 9, press the

buttons
through the

buttons for B through F, respectively.
For Keypad Access Control, press the

button once again to program applicable keypads. Refer to the tables
shown, use the number buttons to enter the data for Keypad 1–4 data in the right digit; and the data for Keypad 5–7
data in the left digit. (Press the

buttons for blank.)
(Direct Entry)


(Direct Entry)


DATA
ENTRY CS RECEIVER 1 FORMAT
blank(•) Ademco Slow, Silent Knight Slow
1 Sescoa, Vertex, DCI, Franklin Fast
2 Radionics Fast
3 Silent Knight Fast
4 Radionics, DCI, Franklin Slow
5 Universal High Speed
8 Radionics BFSK
DATA
ENTRY CS RECEIVER 1 FORMAT
9 FBI 4/3/1
0 Radionics Modem 2
BSIA
C Ademco Point ID
D Ademco Express
E Pager
NOTE: Modem IIe is available only in Direct
Address Programming. Central Station Re-
ceiver 2 and 3 Formats can only be entered in
Direct Address Programming. See CS Re-
ceiver Options.
(Direct Entry)

!
!

GEM-RP2ASe/RP2ASe2 Keypad: CS Account No., CS Format & User Codes
Note: Users are assigned to areas in “Enable User Code by Area” (Address 2500-2531) in Direct Address Programming.

NAPCO Security Systems GEM-P3200 Programming Instructions
WI818B 5/99  Page 13
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above
and press to save. Similarly, to cancel a code, blank out each number of the code press to save.
KEYPAD DISPLAY FUNCTION MENU
FUNCTION LEVEL*
DISPLAY ZN FAULTS 1
DISPLAY ZN BYPASSED 1
DISPLAY ZN DIRECTORY 1
ACTIVATE BELL TEST 1
DISPLAY PHONE #’S 1
DISPLAY SYS TRBL 1
DISPLAY FIRE ALARM 1
DISPLAY FIRE TRBL 1
DISPLAY OP/CL 3
ACTIVATE OVERVIEW 3**
ACTIVATE CHIME 1
ACTIVATE WATCH 2
RESET SYSTEM TRBL 3
RESET SENSOR MSG 3
START EXIT TIME 1
FAULT FIND ***
ACTIVATE LOCATE ***
EZM ZONE FIND ***
ACTIVATE DIALER TEST 3
DISPLAY ALARM LOG 3
DISPLAY TOTAL LOG 3
DISPLAY FIRE LOG 3
DISPLAY OP/CL LOG 3
DISPLAY SYSTEM LOG 3
AUTOARM IN 1-4HRS 2
DISPLAY AUTARM SCHD 3
ACTIVATE PROGRAM 3**
ACTIVATE DOWNLOAD 3
DISPLY RF XMITTER STAT 1
RELAY CONTROL 1
Example:
Program a code of “2222” for user 02, with User Option of “User Program”, User “Level 3” and
Access Control Option “Keypad No. 1”. Enter “2222” for a user code, “2 3” for user option and “blank(•) 1”
Re-
lated User Options: “Ambush Code” (Address 0495), “Panel Access Code” (Address
0490) & “Dealer Security Code” (Address 0500).
OPTIONS EXPLANATION
Disabled User Code not active in this area.
Blocked View Allows User Code to block another code from being viewed by another user.
An unblocked code cannot view a blocked code, but a blocked code can view
all codes. The master user code and the dealer program code can view all
codes.
User Program User Program Option is enabled for Keypad 1 only, wherever it is connected
(Area 1 or Area 2). If enabled, Level 3 must also be enabled.
Bypass Allows User Code to bypass zones.
Overview This option, along with Level 3 Authorization, enables selection of
OVERVIEW mode at a keypad. This Mode provides a system status display of
all areas at a glance.
Arm Only Prevents User Code from disarming this area.
Service A Service Code has restricted arm/disarm rights; if an area is armed with a
Service Code, a “
 
 
” appears on the GEM-RP1CAe2 keypad (a “


”
on the GEM-RP2ASe2 keypad) and the area can be disarmed with any valid
User Code, including a Service Code. If the area is armed with OTHER than a
Service Code, it CANNOT be disarmed with a Service Code. This is typically
used to allow tradesmen access to premises under control of the owner.
Access This is normally used to activate a door striker while an area is disarmed.
Also program “Access Control on Aux. Output” (Address 2418) and “Aux.
Output Access Control Timeout” (Address 2402).
GEM-RP2AS/RP2ASe Keypads: User Codes
USER OPTIONS
USER CODE
(UP TO 6 DIGITS) USER
OPTION USER LEVEL ACCESS CONTROL KEYPADS
123456
DATA
ENTRIES AUTHORITY LEVEL CODE TYPE
blank (•) NONE ARM/DISARM
1 LEVEL 1 ARM/DISARM
2 LEVEL 2 ARM/DISARM
3 LEVEL 3 ARM/DISARM
4 NONE ARM ONLY
5 LEVEL 1 ARM ONLY
6 LEVEL 2 ARM ONLY
7 LEVEL 3 ARM ONLY
8 NONE SERVICE
9 LEVEL 1 SERVICE
0 LEVEL 2 SERVICE
B LEVEL 3 SERVICE
Note: “Y” indicates option is enabled.
USER OPTIONS
DATA
ENTRIES BLOCKED VIEW USER PROGRAM BYPASS OVERVIEW
blank (•) DISABLE
1Y
2Y
3Y Y
4Y
5Y Y
6YY
7Y Y Y
8Y
9Y Y
0Y Y
BY Y Y
CYY
DY Y Y
EYYY
FY Y Y Y
Note: “Y” indicates option is
enabled.
ACCESS CONTROL KEYPADS
DATA
ENTRIES K.P. 5 K.P. 6 K.P. 7
blank (•) NONE
1Y
2Y
3YY
4Y
5Y Y
6YY
7YYY
Note: “Y” indicates option is enabled.
ACCESS CONTROL KEYPADS
DATA
ENTRIES K.P. 1 K.P. 2 K.P. 3 K.P. 4
blank (•) NONE
1Y
2Y
3YY
4Y
5Y Y
6YY
7YYY
8Y
9Y Y
0YY
BYY Y
CYY
DY YY
EYYY
FYYYY
NOTES:
* Minimum Level required to access function
** Level-3 Code with appriopriate user option
*** Requires Dealer Code
Press to save each code.
To proceed to the next User Code, set the cursor to the User Number and change it
using the number buttons. Program a new User Code as previously described. Press
NEXT (

) button to proceed.
Example:
Enter a code of “123456” as
“123456”.

GEM-P3200 Programming Instructions NAPCO Security Systems
WI818B 5/99
Page 14 RF Transmitter Points
(For wireless systems only. Also see Quick Method, which follows)
Press the (

) button to set cursor. For each transmitter (key fob
transmitters also), enter the zone number (01–32) to which the transmitter
will be mapped, the 6-digit RF ID #:1-digit checksum number printed on the
transmitter and box, the point number (1–4);
enter “9” for unsupervised
(all
points). NOTE: When programming the ID Code number, “A” =


; “B” =

; “C” =

; “D” =

; “E” =

; “F” =

. Press to save. Press NEXT (

)
button to proceed.
Quick Method.
If a receiver is already installed in the panel, Napco transmit-
ter wireless points can be programmed automatically (“enrolled”) using the
following procedure. NOTE: The transmitter point will be enrolled only if the
signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be mapped.
2. Press the

button to enter the Enroll Mode. The red and green LEDs
on the keypad will flash and the window will display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-TRANS2 or
GEM-TRANS4 only).
4. Install the transmitter battery. The keypad will beep to indicate that the
point has been successfully enrolled. Multi-point transmitters can be mapped
to successive zones simultaneously (Example 1) or to selected zones point
by point (Example 2).
Example 1. A 4-point transmitter has the RF ID number 410078:1. Map the first three points to Zones 11–13, respectively.
1. Enter the Enroll mode as described in step 2 above.
2. Enter Zone “11”.
3. Open the loops of points 1, 2 and 3.
4. Install the transmitter battery. The keypad will beep 3 times to indicate that three points have been programmed.
Transmitter 410078:1, point 1 will be mapped to Zone 11.
Transmitter 410078:1, point 2 will be mapped to Zone 12.
Transmitter 410078:1, point 3 will be mapped to Zone 13.
The keypad will now display Zone 13, the last zone enrolled.
Example 2. A 2-point transmitter has the RF ID number 287613:1. Map point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone “06”.
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that one point has been programmed. (Transmitter 287613:1,
point 1 will be mapped to Zone 6.)
5. Enter Zone “09”.
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad will beep once to indicate that one point has been
programmed. (Transmitter 287613:1, point 2 is mapped to Zone 9.)
(Direct Entry)


&
(Direct Entry)


&"
KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wireless panic buttons on one
alarm system, each reporting to a central station, a pager or having a description on the keypad that describes the person
holding the key fob, the location where the person holding the key fob is stationed, or the special purpose of the key fob
button being depressed.
See the next pa
g
e on Key fob Zone Assi
g
nment.
GEM-RP2ASe/RP2ASe2 Keypad: RF Transmitter Points

NAPCO Security Systems GEM-P3200 Programming Instructions
WI818B 5/99  Page 15
Key Fob Transmitters
(Press the
(

)
button to set cursor.)
Press the (

) button to set cursor. Keyfobs can be programmed as
“Arm/Disarm” devices (refer to WI752). For each Key Fob Transmitter, enter:
the Key Fob Transmitter number (01–08).
area number to which transmitter is assigned (1 or 2); enter 0 to disable
keyfob.
the 6-digit RF ID # printed on the transmitter (enter all numbers and/or
letters, including leading “0”s, if any).
1-digit checksum number printed on the transmitter (enter all numbers
and/or letters, including leading “0”s, if any).
Aux-1 Option (see key fob aux 1 & aux 2 options).
Aux-2 Option (see key fob aux 1 & aux 2 options).
Note: If the Key Fob is converted for Two Button “Emergency Use”
(by cutting an internal jumper), both top or bottom buttons must be
depressed to activate an alarms. In this case, the Aux-1 and Aux-2
cannot be programmed.
Press to save. Press NEXT (

) button to proceed.
Key Fob Zone Assignment
(refer to display as shown on the previous pa
g
e: press the
(

)
button to
g
o backwards.)
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button = point 2; A1 = point
3; A2 = point 4. Up to 32 key fobs (using 1 button) or 16 key fobs (using 2 buttons) or 8 key fobs (using all 4 buttons) or any
combination up to a maximum of 32 controlled zones can be assigned, providing multiple wireless panic buttons on a
system, each reporting to the Central Station or a pager and/or annunciating on a keypad the key fob zone number with
description/location.
To assi
g
n a key fob to a zone:
program the keyfob as you would a transmitter, entering the keyfob's
ID code, check sum and point number at the appropriate zone. The “Quick Method” is not allowed. The zone may be
hardwired to a sensor as well as assigned to a key fob (either one will activate the zone alarm output). NOTE: If assigning
a key fob to a zone, the “ON/OFF” buttons on the key fob will no longer arm/disarm the system. The key fob is converted
to a “panic only” device.
Enter Date
Press the (

) button to set cursor. Enter the current date in the format
MM/DD/YY, where MM = the month (01–12); DD=the day (01–31); and
YY=the year. Press to save. Press NEXT (

) button to proceed.
Enter Time
Press the (

) button to set cursor. Enter the current time in the format
HH:MMA/P, where HH=hours (01–12); MM=minutes (00–59). Select Am or
Pm by pressing any number button, then press once again to save.
(Direct Entry)
(


&
(Direct Entry)
#
)
*+
DATA
ENTRY AUX 1/AUX 2 OPTIONS
0 None
1 Relay Group 1 Toggle
2 Relay Group 2 Toggle
9Panic
DATA
ENTRY AUX 1/AUX 2 OPTIONS
A Auxiliary
B Instant
C Aux. Output Toggle
D Access on Aux. Output
(Direct Entry)
 
*& EXIT DEALER PROGRAM MODE: This completes the custom default program.
Press the

button to enter the Direct Address Program Mode for further
programming or press the

button once again to end all programming and
resume normal keypad operation.
NOTE: Key fobs 1-8
report as Users 25-32.
GEM-RP2AS/RP2ASe Keypads: Keyfob Transmitters, Date, Time & Exit Dealer Program Mode

GEM-P3200 Programming Instructions NAPCO Security Systems
WI818B 5/99
Page 16

This is an extension of the Dealer Program Mode. This method of programming is used in conjunction with the Keypad
Programming Worksheets that follow. Refer to these worksheets to identify the 4-digit location (address) of the feature to
be programmed. An illustrative example is provided on the next page.

Direct Address Programming allows you to go directly to the address
locations and change the data entries to customize your control panel
options. Whereas the Easy Menu Program Mode is a simple quick
start guide with limited options, the Direct Address Program Mode is
more flexible allowing you to change all the options.
It consists of multiple address locations (up to 4093) with two data
entry locations each (left and right) as shown in the adjacent diagram.


R
  

ARMED
STATUS

 






















NEXT/YES
PRIOR/ NO
AREA
     
    
  
  
DATA ENTRY
LOCATIONS
LEFT DIGIT RIGHT DIGIT
3C
ADDRESS
LOCATIONS
0000
0000
TO
4093
HEXADECIMAL DATA:
BLANK (•) = No Options
1 to 9 = Entries 1 to 9
0 = Entry of 10
B to F = Entries 11 to 15
1. Press


2. Press

Until
“    ”(GEM-RP1CAe2) or
“    ” (GEM-RP2ASe2) appears on LCD
screen.
3. Press

To Enter Dealer Program Mode
4. Press

To Exit Easy Menu Driven Program Mode
& Enter Direct Address Program Mode
Master Security Code
(printed on microprocessor can)
or
Dealer Security Code (Address 0500)
GEM-RP2AS/RP2ASe/RP2ASe2 Keypad
!
GEM-RP1CA/RP1CAe/RP1CAe2 Keypad
!#
$  #
1 2 1 2
= ADDRESS LOCATION
1 2 = DATA ENTRY LOCATION (Left and Right Digits)
Accessing Direct Address Program Mode

NAPCO Security Systems GEM-P3200 Programming Instructions
WI818B 5/99  Page 17

A. GEM-RP1CA/RP1CAe/RP1CAe2 Keypads
B. GEM-RP2AS/RP2ASe/RP2ASe2 Keypad

  
  
Direct Address Program Mode Keypad Commands

GEM-P3200 Programming Instructions NAPCO Security Systems
WI818B 5/99
Page 18
The displays shown on the previous page will appear after a brief delay.
Use the the

button to toggle the cursor between the 4-digit address field and the data entry locations.
Enter the address directly using the number buttons.
The contents of the address will be read automatically, along with the feature name and programming information. The
cursor will advance to the data field. Enter the required data directly using the number buttons.
Press to save the contents of each address.

The Keypad Programming Worksheets in the back are
provided as an address-programming reference to help
the installer modify his custom default program or to make
minor field alterations to an existing panel program. It is
recommended that the panel be uploaded to Napco's
Quickloader software following any keypad programming
and that the PCD3000's error-check feature be utilized to
reduce the possibility of programming omissions or con-
flicts.
Note: Most of the addresses shown comprise two data
entry locations, left and right digits. Program the left digits
on the left data-display segment, and the right digit on the
right segment. For those addresses having only one pro-
grammable nibble, program the right segment only; the
left segment should display a blank (•).
Keep the Keypad Programming Worksheets on file for
future reference.
General Programming Steps
1. Contact the central station to ascertain receiver
format, data format, event codes, subscriber numbers
and telephone number(s).
2. Select the desired features by circling the re-
spective “address” boxes. Refer to the Programming
Options and Worksheets for guidance in selecting the
“data” (1,2,4,8) to be entered into those boxes.
3. Program the data entered in the boxes on the
worksheets into the respective addresses. The display
will show the entry numerically, but will display “0” for the
number 10, and letters “B”, “C”, “D”, “E”, and “F” for the
numbers 11 through 15, respectively. To program a 10,
press

. To program 11 through 15, press

through

, respectively.
NOTE: See the Direct Address Programming Example on the following page.
EXIT DIRECT ADDRESS PROGRAM MODE: When done, press the

button to exit and resume normal keypad
operation.
DATA ENTRY SELECTIONS
(BINARY VALUE CIRCLED) 
ENTRY
TOTAL PRESS


KEYPAD
DISPLAYS
8421blank


•
842


1


1
84


12


2
84




3


3
8


21 4


4
8


2


5


5
8




16


6
8






7


7


421 8


8


42


9


9


4


110


0


4




11


B




21 12


C




2


13


D






114


E








15


F
Table 1. Determining data entry for a location (each
“nibble”). Numbers in parentheses indicate data for se-
lected zones or features. (See Programming Worksheets
that follow.)
Direct Address Program Mode: Program Overview & General Programming Steps

NAPCO Security Systems GEM-P3200 Programming Instructions
WI818B 5/99  Page 19
Direct Address Programming Example
Example:
Program Zones 6, 7 and 8 as Exit/Entry Follower Zones.
DETERMINE THE DATA ENTRIES
1. Referring to ZONE FEATURES in the Programming Worksheets that follow, Exit/Entry Follower for Zones 5
through 8 are located at address 1218, left digit. Circle the data values for Zones 5–8.
2. Add the data values for Zones 6, 7 and 8: 2+4+8=14. From Tables 1 and 2, “14” (E) is entered as press

. The right digit (for Zones 1 through 4, none of which are Exit/Entry Follower Zones) is entered as a
blank (•).
PROGRAM THE DATA ENTRIES
1. Enter the panel's Dealer Security Code (Address 0500), then press the

button.
2. Answer NO (

) to all questions until “    ” is displayed; then press YES (

).
NOTE: If you pass “
  ”, scroll backward using the the

button.
3. Press the

button to enter the Address Program Mode. Address "  " will display.
4. Press

to access Address 1218.
The data for both di
g
its will display and the cursor
will advance to the data field.
5. Press

to enter an “E” in the left digit and press

to enter a blank (•) in the right digit.
6. Press to save.
Address 1218 is now programmed with “E•”.
ZONE OPTION
EXIT/ENTRY FOLLOWER
ZONES
LEFT DATA VALUES
SUM = 14 (CIRCLE )
ZN08 ZN07 ZN06 ZN05






1
ADDRESS
0506
L ADDR R
E 1218 blank (•)
ZONES
RIGHT DATA VALUES
SUM = 0 (CIRCLE )
ZN04 ZN03 ZN02 ZN01
842
1
ENTER DATA 
Direct Address Program Mode: Programming Example

GEM-P3200 Programming Instructions NAPCO Security Systems
WI818B 5/99
Page 20

R
  

ARMED
STATUS

 






















NEXT/YES
PRIOR/ NO
AREA
     
    
  
  
1. Press


2. Press

Until
“    ”(GEM-RP1CAe2) or
“    ” (GEM-RP2ASe2)
appears on LCD screen.
3. Press

To Enter Dealer Program Mode
4. Press

To Exit Easy Menu Driven Program Mode
& Enter Direct Address Program Mode
Dealer Code (Address 0500)
Determining data entry for a location (each “nibble”).
Numbers in parentheses indicate data for selected
zones or features. (See Programming Worksheets
that follow.)
DEFAULTS: The defaults shown on the following pages are automatically set after exiting the Easy Menu Driven Mode.
ENTER DATA 
ADDRESS LOC.
LEFT RIGHT
Program
Option
PROGRAMMING STEPS:
1. Lookup desired Programming Option by
Address Location (highlighted in black).
2. Select the programming option data entry
from the tables shown, by direct entry or by
adding binary values.
3. Enter the selected data entry in the boxes
shown.
4. For more information on a programming
option refer to the Glossary at the end of this
manual.
ENTRY
TOTAL PRESS


KEYPAD
DISPLAYS
blank


•
1


1
2


2
3


3
4


4
5


5
6


6
7


7
8


8
9


9
10


0
11


B
12


C
13


D
14


E
15


F
Direct Address Program Mode: Programming Options & Worksheets