NAPCO Gemini GEM-P816 Installation manual

HARDWIRE WIRELESS
GEM-P816
CONTROL PANEL/COMMUNICATOR
Programming the GEM-P816 Control Panel with the
"Classic" GEM-RP1CAe2 Keypad and the "K Series" GEM-K1CA Keypad
WI995C 3/04© Napco 2004
Quick Start (for "Classic" GEM-RP1CAe2)
1. Refer to the wiring diagram, connect Siren, Aux. Power,
PGM Output, Remote Bus, Earth ground, Zone and Tele-
phone wiring. NOTE: See Installation Instructions
(WI994).
2. Connect AC power first and then the battery.
3. Configure the keypad (see page 34).
4. Access the Easy Menu Driven (Dealer Program) Mode:
Press 456789 A
Press NO (g) until “ACTIVATE PROGRAM Y/N” appears on the
keypad display.
Press YES (F) to Enter Dealer Program Mode. Go to page 5.
Dealer Code
Quick Start (for "K-Series" GEM-K1CA)
1. Refer to the wiring diagram, connect Siren, Aux. Power,
PGM Output, Remote Bus, Earth ground, Zone and Tele-
phone wiring. NOTE: See Installation Instructions
(WI994).
2. Connect AC power first and then the battery.
3. Configure the keypad (see page 34).
4. Access the Easy Menu Driven (Dealer Program) Mode:
Press 456789 R
Press NO (Q) until “ACTIVATE PROGRAM Y/N” appears on the
keypad display.
Press YES (P) to Enter Dealer Program Mode. Go to page 5.
Dealer Code
"K Series" GEM-K1CA
GEMINI
SYSTEM READY
01/01/00 12:00 AM
ARMED
COMPUTERIZED SECURITY SYSTEM
STATUS
R123
B456
C7890
U
NEXT/YES
P
PRIOR/NO
Q
AREA
G
PROGRAMMING
INSTRUCTIONS
R
"Classic" GEM-RP1CAe2
GEMINI
SYSTEM READY
01/01/00 12:00 AM
ARMED
COMPUTERIZED SECURITY SYSTEM
STATUS
A123
B456
C7890
D
NEXT/YES
E
PRIOR/NO
F
AREA
G

CHANGES FROM PREVIOUS EDITION
The following changes have been made to this manual (WI995C) since the previous edition (WI995B):
•Removed the following entries from the index: Change Pulse Output to Cadence, Enable Chirp on RF Arming, Enable Transmitter Telco 1,
Enable Transmitter Telco 3, Select Bell Output on RF Arming.
•Page 4, top, "Downloading From a Computer", the following sentence was added: "Unattended downloading from a computer is not allowed
for Fire Alarm or UL installations."
•Pages 4, 5, and 7, the "50mS Loop Response Zones" entries now contain the following notation: "Note: 750mS is required for Loop Response
time in UL installations."
•Page 7, the "Auto Bypass Re-entry Zones" entry was modified: "Not Evaluated by UL" notation was added.
•Page 8, the "Enter User Codes" entry was modified, and now states to "enter a code from 3 to 6 digits."
•In the Area Options/Explanation chart at the top of page 9, the following information was added: "Ambush: Allows user code to send Ambush
signal to Central Station".
•Top of page 16, under the heading, "Output Timeouts", the following reference was added: "Not UL listed for Commercial Installations".
•Page 18, Address 0720, bit 7 (Change Pulse Output to Temporal Output) was modified with the following notation: "This feature must be pro-
grammed in Fire Alarm applications."
•Page 18--All references to 0720-Bit 6--"Enable PGM2 Chirp on Keyfob Arming" name changed to "Chirp Output on Keyfob Arm/Disarm".
•Page 18--All references to 0722-Bit 0--"Automatic Interior Bypass" name changed to "Automatic Interior Bypass/Easy Exit".
•Page 18--All references to 0721-Bit 7--"Enable Bell Output on Keyfob Arming" name changed to "Select Alarm Output for Keyfob Chirp".
THIS MANUAL INCLUDES FEATURES WHICH ARE ONLY AVAILABLE IN CONTROL PANEL FIRMWARE
VERSION 10 OR LATER.
NAPCO Security Systems, Inc.
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, call toll free: [phone]
For direct line to Technical Service, call toll free: [phone]
Internet: http://www.napcosecurity.com
IMPORTANT NOTE
This manual supports the keypad programming of the GEM-P816 control panel with the NAPCO "classic" GEM-
RP1CAe2 keypad as well as the GEM-K1CA "K Series" keypad. The new "K Series" GEM-K1CA model offers the new
STAY and AWAY buttons with simplified functionality, along with the new MENU and ENTER buttons.
While the instructions in this manual are depicted using the GEM-K1CA keypad, the manual applies to both the "classic"
and the "K Series" keypads.
Program Mode is the same for both keypads--only the button names have changed, as follows:
•The Abutton and the Rbutton operate identically (in Program Mode) for both keypads.
•The Dbutton and the Ubutton operate identically (in Program Mode) for both keypads.
•The button and the button operate identically (in Program Mode) for both keypads. The words
"NEXT/YES button" are used in this manual.
•The button and the button operate identically (in Program Mode) for both keypads. The words
"PRIOR/NO button" are used in this manual.

LNAPCO Security Systems XGEM-P816 Programming Instructions
!
Page 3WI995C 2/04
SYSTEM PROGRAMMING OPTIONS ............................ 4
INTRODUCTION......................................................... 4
DOWNLOADING FROM A COMPUTER .................... 4
EASY MENU DRIVEN PROGRAM MODE ...................... 5
Dealer Program - Preliminary Information................... 5
Accessing Dealer Program Mode................................ 5
Customizing a Default Program .................................. 5
GEM-RP1CAe2/GEM-K1CA Easy Program Menu 6
Total Number of Zones in Area 1 ........................ 6
Fire Zones in Area 1 ............................................ 6
2-Wire Fire Zones in Area 1 ................................ 6
Local or Central Station Reporting System ......... 6
Exit/Entry Zones in Area 1................................... 6
Interior Zones in Area 1 ....................................... 6
24 Hour Zones in Area 1 ..................................... 6
Chime Zones in Area 1........................................ 7
Chime 2 Zones in Area 1..................................... 7
Exit/Entry2 Zones in Area 1................................. 7
50 mS Loop Response Zones ............................. 7
Aux Output Activated on Alarm Zones ............... 7
Sensor Watch Zones .......................................... 7
Keypad Sounder On Alarm Zones...................... 7
Auto Bypass Re-entry Zones............................... 7
Enable No EOLR Zones ...................................... 7
Enable Telco Line Fault Test?............................. 7
Enable Burg Output Chirp on KeyFob? ............... 8
Enable SIA CP-01 Features? .............................. 8
Number of Keypads in Area 1 ............................ 8
Central Station Receiver 1 Telephone Number... 8
Central Station Receiver 1 Account Number....... 8
Central Station Receiver 1 Format ...................... 8
Enter User Codes ............................................... 8
RF Transmitter Points.......................................... 9
Key Fob Transmitters as Arm/Disarm & Control De-
vices.............................................................. 9
Key Fob Transmitters as Zone Input Devices .... 10
Enter Zone Descriptions ...................................... 10
Enter Date ........................................................... 10
Enter Time ........................................................... 10
Dealer Code ........................................................ 10
Clear Dealer Program.......................................... 10
Cold Start............................................................. 10
DIRECT ADDRESS PROGRAM MODE.......................... 11
Direct Address Overview............................................. 11
Address Mode Displays............................................... 11
Binary (Bit) Format............................................. 11
Decimal Format.................................................. 12
Hexadecimal Format.......................................... 13
Programming Conventions Used in this Manual ......... 14
System Delays & Timeouts (Addr 0000-0002, 1059 &
1179) .......................................................................... 15
System Delays & Timeouts (Addr 0711, 0715-0717).. 15
System Output Timeouts (Addr 0710, 0712-0714) ..... 16
Download/Callback Opt. (Addr 1183, 0236-0255) ...... 16
Pager Format Options (Addr 0256 & 0257) ................ 16
Syst. Opt. & Ambush Code (Addr 0460-0485 & 1054) 17
System Options (Addr 0718-0722, 1060-1062) .......... 18
CS Receiver Opt. (Addr 0170-0235) ........................... 19
CS Subscriber Reporting Opt. (Addr 0259-0350) ....... 20
CS Zn Reporting Opt. (Addr 0358-0389 & 0391-0394)21
CS User Reporting Opt. (Addr 0440-0459) ................. 22
EZM Group & Area Arming Opt. (Addr 0737-0744) .... 23
Area Bell Control Options (Addr 0745-0749) .............. 24
Keypad Options (Addr 0723-0736) ............................. 25
Zones 1-16 Options (Addr 0490-0595) ....................... 26
RF Rcvrs. & Sup. Timers (Addr 1038-1053 & 1180)... 30
Clear Program Features (Addr 1197 & 1198) ............. 31
USER PROGRAM MODE................................................ 31
Preliminary Information ............................................... 31
Accessing User Program Mode .................................. 32
User Codes ................................................................. 32
Zone Descriptions ....................................................... 33
Date............................................................................. 33
Time ............................................................................ 33
KEYPAD CONFIGURATION MODE ............................... 34
Keypad Installation...................................................... 34
Configuring the Keypads............................................. 34
EASY MENU PROGRAMMING WORKSHEETS ............ 36
ALPHABETICAL INDEX ................................................. 39
ADDRESS NUMBER INDEX ........................................... 42
GEM-P816 WIRING DIAGRAM ....................................... 48
TABLE OF CONTENTS
Refer to accompanying GEM-P816 Installation Instructions (WI994) for installation information.

XGEM-P816 Programming Instructions LNAPCO Security Systems
!Page 4 WI995C 2/04
SYSTEM PROGRAMMING OPTIONS
INTRODUCTION
The GEM-P816 control panel may be programmed by various means, each of which will be covered in detail in the sec-
tions that follow. Keypad displays shown are for a GEM-RP1CAe2/GEM-K1CA (version 8 keypad), the recommended
keypad for programming. For Programming Instructions with the GEM-RP2ASe2/GEM-K2AS, GEM-RP3DGTL/GEM-
K3DGTL and the GEM-RP4RFC/GEM-K4RF series, see WI1182.
!Downloading From a Computer. This is the preferred method of programming. The panel may be
downloaded from (or uploaded to) an IBM PC-compatible computer, either locally or remotely. Napco's PCD3000
Quickloader software features context-sensitive help screens as well as an error-checking utility that prevents pro-
gramming of incompatible or conflicting data to ensure proper panel operation. Note: Unattended downloading from
a computer is not allowed for Fire Alarm or UL installations.
!Easy Menu-Driven Program (Dealer Program) Mode - Keypad Programming. The Easy Menu-Driven
Program Mode allows keypad programming of number of zones in area 1, number of fire zones (both 4-wire and 2-
wire), local or Central Station reporting, number of exit/entry zones, number of interior zones, number of 24 hour
zones, number of chime zones, Chime 2 zones, Exit/Entry2 zones, 50ms loop response zones (Note: 750mS is re-
quired for Loop Response time in UL installations), aux output activated on alarm zones, sensor watch zones,
keypad sounder on alarm zones, auto bypass re-entry zones, EOLR zones, number of keypads in area 1, Central
Station telephone number, Central Station account number, Central Station receiver format, User Codes, RF trans-
mitter points, RF keyfob transmitters, zone descriptions, date/time, dealer code, Telco line fault test, Burg output chirp
on keyfob, keypad time/date display, enable CP-01 programming, and clear dealer program/cold start. For new pan-
els, a custom default program may be created at the keypad. A menu-driven utility prompts the installer to configure
the system. Further detailed customization is accomplished in the Direct Address Program Mode.
!Direct Address (Dealer Program) Program Mode - Keypad Programming. The Direct Address Pro-
gram Mode is an extension of the Dealer Program Mode wherein data is entered at the keypad by location. This
mode is accessed from the Easy Menu Driven Program Mode by pressing the Cbutton at any time.
!User Program Mode - Keypad Programming. The User Program Mode is intended for
authorized users and is limited to keypad programming of User Codes, Time, Date and Zone
Descriptions.
DOWNLOADING FROM A COMPUTER
The control-panel program may be downloaded from the computer by any of the following methods.
Local Downloading
(Note: This procedure should be used after installation, after peripheral devices are connected).
For direct high-speed data transfer to the control panel from a desktop computer, connect the download jack (JP2)
on the panel to the LOCAL jack (J3) on the Napco PCI2000/3000 computer interface using the supplied 6-
conductor cable. (Refer to PCI2000/3000 Installation Instructions WI443 for wiring diagram and procedures).
Similarly, a high-speed local download may be made in the field using a notebook or laptop computer. Connect
JP2 on the control panel to a Napco PCI-MINI computer interface using the 6-conductor cable supplied. (Refer to
PCI-MINI Installation Instructions WI767).
Remote Downloading
(Also see PCI2000/3000 Installation Instructions WI443). Note: Unattended downloading from a computer is not
allowed for Fire Alarm or UL installations.
Function Mode
Start by establishing a telco connection between the computer operator and the installer. During this procedure,
voice contact will be lost, therefore both the installer and the computer operator should be familiar with the opera-
tion. When a steady high-pitched tone is heard at the site phone, access the “ACTIVATE DOWNLOAD” Function (see
Keypad Programming Modes), then press the Jor Ubutton or the NEXT/YES button; the site phone will go dead.
Hang up the phone and wait for a call from the central station confirming a successful download.
Callback Method
An installed, unattended panel may be programmed or reprogrammed remotely using the Callback-Method
Download feature of the PCD3000 software. Remote downloading requires a modem compatible with the
PCI2000/3000. Upon answering the call from the computer, the panel will verify the Download Security Code and,
if confirmed, will establish a connection. If a Callback Number is programmed into the panel, the panel will auto-
matically disconnect and call the computer at this number before establishing a connection.

LNAPCO Security Systems XGEM-P816 Programming Instructions
!
Page 5WI995C 2/04
EASY MENU DRIVEN PROGRAM MODE
DEALER PROGRAM - PRELIMINARY INFORMATION
!Only Keypad #1 may be used for both Dealer and User programming, however this keypad may be located in any area.
!The Default Dealer Code is 456789. Use this code to enter the Dealer Program Mode
to program a custom Dealer Code, which replaces the Default Dealer Code. If you clear your Dealer Code, use the Default
Dealer Code once again to enter programming.
!After entering codes or data, press the save Ubutton. Data will not be stored into memory unless Uis pressed.
!If the keypad is in the Program Mode and no activity is detected for longer than 4 minutes, a steady tone will sound.
!Silence the sounder by the Gbutton to continue, or by pressing the Cbutton to exit.
!A panel that has been COLD STARTED (Address Location 1198) performs identically to a new panel.
!When programming a Multiple Area System, Direct Address Programming Mode must be used to complete the program.
KEYPAD #1: KEYPAD #1: For ease of programming, it is recommended that a GEM-RP1CAe2 or GEM-K1CA be
used as Keypad #1. (Regardless of which keypad is selected, all new keypads are configured as Keypad #1 out of the
box). If a GEM-RP2ASe2/GEM-K2AS is used, see WI1182.
1. Press 456789 R
2. Press PRIOR/NO button until “ACTIVATE PROGRAM Y/N”appears on LCD screen.
3. Press NEXT/YES button to Enter Dealer Program Mode.
4. Press CC to Exit Dealer Program Mode when finished.
Dealer Code (Default = 456789)
•Number of Zones in Area 1
•Fire Zones in Area 1
•2-Wire Fire Zones in Area 1
•Local or Central Station Reporting System
•Exit/Entry Zones in Area 1
•Interior Zones in Area 1
•24 Hour Zones in Area 1
•Chime Zones in Area 1
•Chime 2 Zones in Area 1
•Exit/Entry2 Zones in Area 1
•50mS Loop Response Zones (Note: 750mS is
required for Loop Response time in UL installations).
•Aux Output Activated on Alarm Zones
•Sensor Watch Zones
•Keypad Sounder on Alarm Zones
•Auto Bypass re-entry Zones
•Enable no EOLR Zones
•Number of Keypads in Area 1
•Central Station Receiver 1 Tel. Number
•Central Station Receiver 1 Account Number
•Central Station Receiver 1 Format
•Enter User Codes
•RF Transmitter Points
•Quick Method
•Key Fob Transmitters
•Enter Zone Descriptions
•Enter Date
•Enter Time
•Dealer Code
•Enable Telco Line Fault Test
•Enable Burg Output Chirp on Keyfob
•Enable Keypad Time/Date Display
•Enable CP-01 Programming
•Clear Dealer Program
•Cold Start
NEW PANELS: The custom default program may be created for new panels only. Once the panel has been programmed by any
means, the number zones will be suppressed and cannot be changed. Should it be necessary to create a new custom default pro-
gram, (a) from the Dealer Program Mode, press the Cbutton to enter the Direct Address Program Mode; (b) access Location
1197 (Clear Program); (c) press the Ubutton and start over.
EASY MENU DRIVEN PROGRAM MODE
This procedure will automatically set up system keypads, EZMs, wireless transmitters, etc. After your basic default program has
been loaded, you may alter it as necessary in the Direct Address Program Mode.
ACCESSING DEALER PROGRAM MODE
CUSTOMIZING A DEFAULT PROGRAM
For new panels, you can design a default program that will best suit your application. Using this procedure, you will configure the panel for:

XGEM-P816 Programming Instructions LNAPCO Security Systems
!Page 6 WI995C 2/04
GEM-RP1CAe2/GEM-K1CA Keypad Easy Program Menu
To create a custom program using the GEM-RP1CAe2/GEM-K1CA keypad, simply answer the following questions and record
your information on the Easy Menu Programming Worksheet. In each of the following steps, press Rto set cursor, the
NEXT/YES button to go forwards, the PRIOR/NO button to go backwards, Uto save and Ctwice to exit at any time.
Total Number of Zones in Area 1 (New Program Only)
•Enter the total number of zones to be programmed for Area 1.
•Valid entries are from 01 to 32. Directly enter the total number of zones, including leading zeros.
•The system is based on groups of 4 zones each (after the first 8 zones), and will automatically
round up to the next group of 4. For example, if you enter 18, it will automatically convert this to
20 zones. Press Uto save. Press the NEXT/YES button to proceed.
Fire Zones in Area 1 (New Program Only)
•Enter the zone number of any Fire Zones (including 2-wire, 4-wire or wireless).
•Valid entries are from 01 to 32.
•Directly enter each zone number, including leading zeros, and press Uto save, and then re-
peat for any additional zone(s). Press the NEXT/YES button to proceed.
2-Wire Fire Zones in Area 1 (New Program Only)
•Enter the zone number of any Fire Zone (from previous question) to be used with 2-wire
smoke detectors.
•Valid entries are 07 and 08. Directly enter each zone number, including leading zeros.
•Press Uto save, and repeat for any additional zone(s); press NEXT to proceed.
NOTE: Only zones which have been designated as Fire Zones can be programmed as 2 Wire
Fire zones. JP3 must be set to “2-WF” position for 2-wire fire. (refer to Installation Instructions).
Local or Central Station Reporting System (New Program Only)
Press the NEXT/YES button for all zones to report; press the PRIOR/NO button for local system
Exit/Entry Zones in Area 1 (New Program Only)
•Enter the zone numbers of zones to be used as Exit/Entry zones.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.
NOTE: Exit/Entry Entry time of 30 seconds will automatically be programmed.
Interior Zones in Area 1 (New Program Only)
•Enter the zone numbers to be used as Interior Zones.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s).
•Press the NEXT/YES button to proceed.
•All Interior zones will also be automatically programmed as “Exit/Entry Follower” and as
"Power Up Delay" zones.
24 Hour Zones in Area 1 (New Program Only)
•Enter the zone numbers of zones to be used as 24 Hour zones.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.
NOTE: 24 Hour Zones will automatically be programmed as audible (Burg Output).
EASY MENU DRIVEN PROGRAM MODE
(Direct Entry)
#of Zns in Area1
Enter # Zones XX
(Direct Entry)
Fire Zones
Enter Zone # °°
(Direct Entry)
2-Wire Fire Zns
Enter Zone # °°
(Press YES or NO)
Report All Zones
To Central? Y/N
(Direct Entry)
Exit/Entry Zones
Enter Zone # XX
(Direct Entry)
Interior Zones
Enter Zone # XX
(Direct Entry)
24 Hour Zones
Enter Zone # °°

LNAPCO Security Systems XGEM-P816 Programming Instructions
!
Page 7WI995C 2/04
EASY MENU DRIVEN PROGRAM MODE
Chime Zones in Area 1 (New Program Only)
•Enter the zone numbers which are to be used as Chime Zones.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), press the NEXT/YES button to proceed.
NOTE: A chime time of 2 seconds will be automatically programmed.
Chime 2 Zones in Area 1 (New Program Only)
•Enter the zone numbers which are to be used as Chime 2 Zones.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
NOTE: A chime time of 2 seconds will be automatically programmed.
Chime 2 zones give a distinct pulsating tone when zone is faulted.
Exit/Entry2 Zones in Area 1 (New Program Only)
•Enter the zone numbers of zones to be used as Exit/Entry zones.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.
NOTE: An Exit/Entry 2 Entry Time of 30 seconds will automatically be programmed.
50 mS Loop Response Zones (New Program Only) Note: 750mS is required for Loop Re-
sponse time in UL installations.
•Enter the zone numbers of zones to be have a 50mS loop response.
•Valid entries are from 01 to 08. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
Note: Only panel zones 01-08 can be programmed for Quick Loop Response. All other zones can be
programmed via their respective EZM's (hardwire).
Aux Output Activated on Alarm Zones (New Program Only)
•Enter the zone numbers of zones to activate the PGM2 upon alarm.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
NOTE: A PGM2 Timeout of 15 minutes will automatically be programmed.
Sensor Watch Zones (New Program Only)
•Enter the zone numbers of zones to be Sensor Watch zones.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
NOTE: A Sensor Watch Time of 24 hours will automatically be programmed.
Keypad Sounder On Alarm Zones (New Program Only)
•Enter the zone numbers of all zones to activate the Keypad Sounder upon alarm.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
Auto Bypass Re-entry Zones (New Program Only) (Not evaluated by UL)
•Enter the zone numbers of zones to be Auto Bypass Re-entry zones.
•Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
•Auto Bypass Re-entry Zones allow the system to be armed with the zone faulted but come back into
the system (armed) when the zone is subsequently closed.
Enable No EOLR Zones (New Program Only)
•Press YES to program all zones except 24 Hr & fire zones for No End Of Line Resistor. Press NO to
continue.
•Do not program this feature for UL Installations.
Enable Telco Line Fault Test?
•Press YES to enable Telco Line Fault Test.
•Press NO to continue. NOTE: If enabled, a Telco Line Fault Test Delay of 60 sec. will auto-
matically be programmed.
(Direct Entry)
Chime Zones
Enter Zone # °°
(Direct Entry)
Chime 2 Zones
Enter Zone # °°
(Direct Entry)
Exit/Entry2 Zones
Enter Zone # °°
(Direct Entry)
50mS Loop Zones
Enter Zone # °°
(Direct Entry)
Aux Output Zones
Enter Zone # °°
(Direct Entry)
Sensor Watch Zns
Enter Zone # °°
(Direct Entry)
KP Sndr Alrm Zns
Enter Zone # °°
(Direct Entry)
Auto Byp REnt Zn
Enter Zone # °°
(Press YES or NO)
Enable No EOLR
Zones Y/N
(Press YES or NO)
Enable Telco
Line Test? Y/N

XGEM-P816 Programming Instructions LNAPCO Security Systems
!Page 8 WI995C 2/04
EASY MENU DRIVEN PROGRAM MODE
Enable Burg Output Chirp on KeyFob?
•Press the NEXT/YES button to enable Burg Output Chirp on KeyFob Arm / Disarm.
•Press the PRIOR/NO button to continue.
NOTE: The Burg Output will chirp once on Keyfob Arm and twice on Keyfob Disarm.
Enable SIA CP-01 Features?
•Press the NEXT/YES button to enable.
•Press the PRIOR/NO button to continue.
The SIA CP-01 Features are designed to reduce the incidence of false alarms. NOTE: Do not
enable unless reporting, otherwise system trouble Fail to Communicate may occur.
Number of Keypads in Area 1
•Enter the total number of Keypads to be installed in Area 1.
•Valid entries are from 01 to 07. Directly enter the number of keypads, including leading zeros.
Press Uto save. Press the NEXT/YES button to proceed.
NOTE: Area 2 keypads must be assigned in Direct Address Programming. See Keypad Options.
Central Station Receiver 1 Telephone Number
•Enter telephone number of up to 16 digits.
•Press 1through 9for digits 1–9; G0for a zero and 0for a blank (•).
•Press G1through G5for letters B–F, respectively.
•Pre-Dial Delay = “D” (G4); Dial-Tone Detection = “E” (G5).
•Press Uto save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Ad-
dress Programming. See CS Receiver Options.
Central Station Receiver 1 Account Number
•Enter an account number of up to four digits.
•Press 0through 9for digits 0–9, and G0for a blank (•).
•Press Uto save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Account Numbers
must be entered in Direct Address Programming. See CS
Reporting Options.
Central Station Receiver 1 Format
•From the table at the right enter the receiver format.
•Press 0through 9, and G0 for blank (•).
•Press G1 through G4 for letters B–E.
•Press Uto save and press the NEXT/YES button to proceed.
Enter User Codes (Press Rto set cursor.)
For default program, enter up to 32 User Codes, with Area 1 and Area 2 Options.
•Press the (R) button once to set the cursor to the User Code.
•Press 0through 9to enter a code from 3 to 6 digits, leave blank (•) any trailing boxes.
•Press Rto set the cursor to the Area 1 Options Level. Refer to the table below for available op-
tions. For Area 2 Options, press the Rbutton once again.
•If “Enable Global Ambush Code” (Address 0720) is enabled and “Global Ambush Code” (Address 1054) is not left blank (•), do not program the
first two digits of ANY User Code the same as the “Global Ambush Code”.
•Press Uto save. Note: Duplicate User Codes are not allowed; therefore a duplicate Code entered in the LCD Window will erase when Uis
pressed. To proceed to the next User Code, press Rto set the cursor to the User Number and change it using the number buttons. Press
the NEXT/YES button to proceed.
(Direct Entry)
Central Phone #
(Direct Entry)
Central Station
Account # (____)
DATA
ENTRY
CS RECEIVER 1 FORMAT
•
(blank)
Ademco Slow, Silent Knight
Slow
2 Radionics Fast
3 Silent Knight Fast
4 Radionics, DCI, Franklin Slow
5 Universal High Speed
B SIA
C Ademco Point ID
E Pager
(Direct Entry)
See WI for Info
Rcvr Format (0)
Enter user code
U01 123 - 9-
User# User Code Area 1 Area 2
OPTION
ENABLED
Disabled
Arm/Disarm
Arm Only
Service
Access
Ambush
* User Program
L R
blank(•) blank
blank(•) 1
blank(•) 2
blank(•) 3
blank(•) 4
blank(•) 5
DATA ENTRIES
blank(•) Add 8
USER AREA OPTIONS
USER OPTIONS
USER CODE
(UP TO 6 DIGITS)
AREA 1
OPTIONS
AREA 2
OPTIONS
Example: Program a code of “2222” for user
02, with area 1 options of “Arm/Disarm” and
“User Program”. Enter “2222” for a user code,
“• (blank) 9” for area 1 options and “• (blank) •
(blank)” for area 2 options.
(Direct Entry)
# Area 1 Keypads
Enter # KPs 01
(Press YES or NO)
Enable SIA CP-01?
Y/N
(Press YES or NO)
Enable Burg Out
Chirp? Y/N

LNAPCO Security Systems XGEM-P816 Programming Instructions
!
Page 9WI995C 2/04
EASY MENU DRIVEN PROGRAM MODE
RF Transmitter Points (Press Rto set cursor.)
For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)
•The zone number (01–32) to which the transmitter will be mapped.
•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•The point number (1–2); enter “9” for unsupervised (all points).
•Press Uto save and NEXT/YES button to proceed when all transmitters have been entered.
NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A =
G0; B = G1;
C = G2; D = G3; E = G4and “F” = G5.
Quick Method. If a receiver is already installed in the panel, transmitter wireless points can be
programmed automatically (“enrolled”) using the following procedure. NOTE: The transmitter
point will be enrolled only if the signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be mapped.
2. Press Bto enter the Enroll Mode. The red and green LEDs on the keypad will flash and the
window will display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).
4. Install the transmitter battery. The keypad will beep to indicate that the point has been successfully
enrolled. Multi-point transmitters can be mapped to successive zones simultaneously.
Key Fob Transmitters as Arm/Disarm & Control Devices (Press Rto set cursor).
Key fobs can be programmed as “Arm/Disarm” devices using their On/Off buttons (refer to
WI752). For each Key Fob Transmitter, enter:
•The Key Fob Transmitter number (01–8).
•The area number to which transmitter is assigned (0 to disable keyfob, 1 or 2).
•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•The Aux 1 Option (see key fob aux 1 & aux 2 options).
•The Aux 2 Option (see key fob aux 1 & aux 2 options).
•Press Uto save and NEXT/YES button to proceed when all key fobs have been entered.
NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A = G0; B = G1;
C = G2; D = G3; E = G4and “F” = G5.
ZN# XMIT#+CS P
Zn01- 000000:0-0
Zone # Xmitter Check Point
Mapped to ID Sum #
ZN# XMIT#+CS P
Zn01- 000000:0-0
ZN# XMIT#+CS P
ZN01- ENROLL:A--
Example. A 2-point transmitter has the RF ID number 287613:1.
Map point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone “06”.
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that
one point has been programmed. (Transmitter 287613:1, point
1 will be mapped to Zone 6).
5. Enter Zone “09”.
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad
will beep once to indicate that one point has been programmed.
(Transmitter 287613:1, point 2 is mapped to Zone 9).
KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm
system, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the key
fob, the location where the person holding the key fob is stationed, or the special purpose of the key fob button being depressed.
See the next page on Key Fob Transmitters as Zone Input Devices .
KF A XMIT#+CS OP
01-0 000000:0 00
KF Area Xmitter Check Aux
# ID Sum 1&2
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above and press Uto save. Similarly, to
cancel a code, blank out each number of the code and press Uto save.
AREA OPTIONS EXPLANATION
Disabled User Code not active in this area.
Arm/Disarm Allows User Code to arm/disarm this area.
Arm Only Prevents User Code from disarming this area.
Service A Service Code has restricted arm/disarm rights; if an area is armed with a Service Code, a “MONITOR ON” appears on the GEM-RP2ASe2 key-
pad and the area can be disarmed with any valid User Code, including a Service Code. If the area is armed with OTHER than a Service Code,
Access This is normally used to activate a door strike while an area is disarmed. Also program “Access Control on PGM2. Output” (Address 0719) and
“PGM2 Output Access Control Timeout” (Address 0711).
* User Program User Program Option is enabled for Keypad 1 only, wherever it is connected (Area 1 or Area 2). To enable User Program Option for any user
add 8 to the data entry for Area Option (see example). Then, User Programming can be performed only at Keypad 1 by a user code with user
program enabled.
Related User Options:“Enable Global Ambush Code” (Address 0720), “Global Ambush Code” (Address 1054) & “Enable Managers Mode” (Address 0719).
Ambush Allows user code to send Ambush signal to Central Station.

XGEM-P816 Programming Instructions LNAPCO Security Systems
!Page 10 WI995C 2/04
Key Fob Transmitters as Zone Input Devices
(Refer to display above: press the PRIOR button to go backwards).
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off
button = point 2; A1 = point 3; A2 = point 4. Up to 32 key fobs (using 1 button) or 16 key fobs
(using 2 buttons) or 8 key fobs (using all 4 buttons) or any combination up to a maximum of 32
controlled zones can be assigned, providing multiple wireless panic buttons on a system, each re-
porting to a Central Station or a pager and/or annunciating on a keypad the key fob zone number
with a description. To assign a key fob to a zone: program the key fob as you would a transmitter,
entering the key fob's ID code, check sum and point number at the appropriate zone. The “Quick
Method” is not allowed. The zone may be hardwired to an electrical sensor as well as assigned to
a key fob (either one will activate the zone alarm output). NOTE: If assigning a key fob to a zone,
the “ON/OFF” buttons on the key fob will no longer arm/disarm the system. The key fob is con-
verted to a “panic only” device.
Enter Zone Descriptions
•Press 1and 2to place the cursor and; press 3and 6to select the character.
•For each zone, enter a description of up to two lines.
•Press Uto save each description.
•To proceed to the next description, place the cursor under the Zone Number (e.g. “01”) and change the Zone Number using 3
and 6. Program new description as above.
•NOTE: Zone Descriptions can only be entered through the GEM-RP1CAe2 Keypad or by using the Napco Quickloader Software.
See Easy Menu Programming Worksheet for available zone description characters.
Enter Date (Press Rto set cursor).
•Enter the current date in the format MM/DD/YY. (MM = month, DD = day and YY = year.
•Press Uto save. Press the NEXT/YES button to proceed.
Enter Time (Press Rto set cursor.)
•Enter the current time in format HH:MMA/P, where HH=hours (01–12); MM=minutes (00–
59).
•Select AM or PM by pressing any number button.
•Press Uto save. Press the NEXT/YES button to proceed.
Dealer Code
•Directly enter the Dealer Code (default = 456789), using 0through 9buttons.
•Press Uto save.
•Re-enter the Dealer Code to verify the previous code.
•Press Uto save.
•Press the NEXT/YES button to proceed.
(Direct Entry)
Enter Date
( / / )
(Direct Entry)
Enter Time
( : )
Dealer Code
456789
DEALER CODE
RE-ENTER
CLEAR PROGRAM: Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press
Cto enter the Address Program Mode; (b) access Location 1197 (Clear Program) or 1198 (Cold Start); (c) press Uand then
(d) press Cto exit the Dealer Program Mode. A “SYSTEM TROUBLE/E09-00 SERVICE” will occur. Press Cto silence the keypad.
Clear Dealer Program (Erases Dealer Program)
Use this feature to erase the Panel Program, while maintaining Scheduled Data and Zone Descrip-
tions. Access address 1197 and press U. Data entry is not allowed. NOTE: Enter Easy
Menu Driven Program Mode to reprogram system.
Cold Start (Erases Entire Program)
This erases all programmed data (Dealer Program, Zone Description Data and Schedules).
Access address 1198 and press U. Data entry is not allowed. NOTE: Some features
(schedules) can only be programmed again with the Downloading Software.
EASY MENU DRIVEN PROGRAM MODE
DATA
ENTRY
AUX 1/AUX 2
OPTIONS
0 None
1 Relay Group 1 Toggle
2 Relay Group 2 Toggle
9 Keypad Panic
A Keypad Aux.
B Instant
C PGM2 Ouput Toggle
D Access on PGM2 Output
E Arm STAY
F Interior Button
(Direct Entry)
01-
EXIT DEALER PROGRAM MODE: This completes the custom default program. Press Cto enter the Direct Address Program
Mode for further programming or press Conce again to end all programming and resume normal keypad operation.
1197 XX H
1198 XX H

LNAPCO Security Systems XGEM-P816 Programming Instructions
!
Page 11WI995C 2/04
DIRECT ADDRESS OVERVIEW
Direct Address Programming allows you to go directly to the address locations (up to 1198) and change the data entries
manually in order to customize your control panel options. Whereas the Easy Menu Program Mode guides you through
limited selections to get you started, Direct Address Program Mode allows you to change all options directly. It con-
sists of up to 1198 address locations each with data entry locations as shown in the following diagram (below left). The
data entry location accepts data in one of three formats: Binary, Decimal and Hexadecimal (explained below in
"Address Mode Displays"). The following diagram (below right) illustrates a Decimal format data entry location (using
a GEM-RP1CAe2 keypad).
ADDRESS MODE DISPLAYS
There are three types of address displays when programming in Direct Entry Program Mode, as follows:
A) Binary (Bit) Format
Settings (such as Zone Features) display and accept data in "number" format. For example, Zone Features are
turned on by the pressing of keypad buttons 1 through 8, with the activated Zone(s) displaying the corresponding
decimal digit (replacing deactivated zones which are signified by dashes).
EXAMPLE: BIT Format with the GEM-RP1CAe2: Program Zones 2, 4, 5 and 7 as Exit/Entry Follower Zones.
DETERMINE THE DATA ENTRIES
1. Referring to ZONE FEATURES in the Programming Worksheets that follow, the Exit/Entry Follower for Zones 1
through 8 are located at address 0506.
DATA ENTRY
LOCATION
ADDRESS
LOCATIONS
0000
0000
TO
1198
DATA ENTRY LOCATION:
(One of three formats):
•Binary (Bit)
•Decimal
•Hexadecimal
DIRECT ADDRESS PROGRAM MODE
Direct Address Program Mode
GEM-RP1CAe2 Keypad Display Example
0000 060 D
1 2
= ADDRESS LOCATION
1
2 = DATA ENTRY LOCATION
0506 - - - - - - - - B 0506 - 2 - 4 5 - 7 - B
DATA ENTRY LOCATION:
Binary (Bit) Format
Press 245and 7in
order to activate Zones 2, 4, 5, and 7. (The "B"
on the right indicates "Binary" format).
DATA ENTRY LOCATION:
Binary (Bit) Format
•No zones yet activated
Address
0506
"Exit/Entry
Follower"
Address
0506
"Exit/Entry
Follower"

XGEM-P816 Programming Instructions LNAPCO Security Systems
!Page 12 WI995C 2/04
PROGRAM THE DATA ENTRIES
1. Enter the panel's Dealer Security Code, then press R.
2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass
“ACTIVATE PROGRAM”, scroll backward using B.
3. Press Cto enter the Address Program Mode. Address "0000" will display.
4. Press 0506 to access Address 0506. The existing data will display and the cursor will
advance to the data field.
5. Press 678. The numbers 6,7 and 8 will appear on the keypad display indicating the zones
activated.
6. Press Uto save. Address 0506 is now programmed with “6,7,8”.
7. Enter another 4-digit address to continue programming or press Cto exit and resume normal keypad op-
eration.
B) Decimal Format
Settings (such as Entry and Exit Delay) display and accept data in decimal format, as a 3 digit number. Data is en-
tered directly, by pressing keys 0 – 9, with the cursor automatically moving to the right upon each key press.
EXAMPLE: DECIMAL Format with the GEM-RP1CAe2: Program Abort Delay to be 15 seconds.
DETERMINE THE DATA ENTRIES
1. Referring to SYSTEM DELAYS & TIMEOUTS in the Programming Worksheets that follow, the Abort Delay is
located at address 0715:
PROGRAM THE DATA ENTRIES
1. Enter the panel's Dealer Security Code, then press R.
2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass
“ACTIVATE PROGRAM”, scroll backward using B.
3. Press Cto enter the Address Program Mode. Address "0000" will display.
4. Press 0715 to access Address 0715. The existing data will display and the cursor will
Direct Address Program Mode
0715 - - - D 0715 015 D
ZONES 1 "8 ZONES 9 "16
ZONE FEATURES ADDR Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 ADDR Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z16
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Exit/Entry Follower 0506
6 7 8
0561
DATA ENTRY LOCATION:
Decimal Format
•No time yet entered
Address
0715
"Abort
Delay"
DATA ENTRY LOCATION:
Decimal Format
Press 015in order to set
"Abort Delay" to 15 seconds. The "D" on the
right indicates "Decimal" format.
ABORT ADDRESS 0715
DELAY
(sec.)
[Default = 0 sec. = blank (•)]
Address
0715
"Abort
Delay"

LNAPCO Security Systems XGEM-P816 Programming Instructions
!
Page 13WI995C 2/04
Direct Address Program Mode
advance to the data field.
5. Press 015. The numbers 015 will appear on the keypad display indicating the number of
seconds entered.
6. Press Uto save. Address 0715 is now programmed with a 15-second Abort Delay.
7. Enter another 4-digit address to continue programming or press Cto exit and resume normal keypad
operation.
C) Hexadecimal Format
Data such as Report Codes displays and accepts data by means of a Hexadecimal display. Data is entered di-
rectly, by pressing keys 1 – 9, G0 for zero, and G1through G5for hex B through F (11-15),
with the cursor automatically moving to the right upon key press. See table below.
EXAMPLE: HEXADECIMAL Format with the GEM-RP1CAe2: Program Chime Timeout to be 2 seconds.
DETERMINE THE DATA ENTRIES
1. Referring to SYSTEM DELAYS & TIMEOUTS in the Programming Worksheets that follow, the Chime Timeout
is located at address 0716. In the "Chime Timeout Options" table, the data entries needed to assign a time-
out of 2 seconds are "blank" and "8".
ENTRY
TOTAL
PRESS
N KEYPAD
DISPLAYS
ENTRY
TOTAL
PRESS
N KEYPAD
DISPLAYS
blank 0 • 8 8 8
1 1 1 9 9 9
2 2 2 10 G 0 0
3 3 3 11 G 1 B
4 4 4 12 G 2 C
5 5 5 13 G 3 D
6 6 6 14 G 4 E
7 7 7 15 G 5 F
HEXADECIMAL ENTRIES
CHIME ADDRESS 0716
TIMEOUT
(¼sec.)
[Default = 2 ¼sec. = ½ sec.]
DATA ENTRY LOCATION:
Decimal Format
•No time yet entered
DATA ENTRY LOCATION:
Decimal Format
Press 08in order to set "Chime
Timeout" to 2 seconds. The "H" on the right
indicates "Hexadecimal" format.
Address
0716
"Chime
Timeout"
0716 - - H 0716 - 8 H
Address
0716
"Chime
Timeout"
2 seconds
CHIME TIMEOUT OPTIONS
TIMEOUT
LEFT RIGHT
blank (•) blank (•) 0 x ¼sec. = 0 sec.
blank (•) 2 2 x¼sec. = ½ sec.
blank (•) 3 3 x ¼sec. = ¾ sec.
blank (•) 4 4 x ¼sec. = 1 sec.
blank (•) 5 5 x ¼sec. = 1.25 sec.
blank (•) 6 6 x ¼sec. = 1.5 sec.
blank (•) 7 7 x ¼sec. = 1.75 sec.
blank (•) 8 8 x ¼sec. = 2 sec.
F F 255 x ¼sec. = 63.25
DATA ENTRIES

XGEM-P816 Programming Instructions LNAPCO Security Systems
!Page 14 WI995C 2/04
Direct Address Program Mode
PROGRAM THE DATA ENTRIES
1. Enter the panel's Dealer Security Code, then press R.
2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass “ACTIVATE
PROGRAM”, scroll backward using B.
3. Press Cto enter the Address Program Mode. Address "0000" will display.
4. Press 0716 to access Address 0716. The existing data will display and the cursor will ad-
vance to the data field.
5. Since you wish the timeout to be for 2 seconds (and 8 multiplied by ¼ second equals 2 seconds), press
08. The numbers 08 will appear on the keypad display indicating the number of seconds entered.
6. Press Uto save. Address 0715 is now programmed with a 2-second chime.
7. Enter another 4-digit address to continue programming or press Cto exit and resume normal keypad op-
eration.
PROGRAMMING CONVENTIONS USED IN THIS MANUAL
The Keypad Programming Worksheets in the back are provided as an address-programming reference to help the in-
staller modify his custom default program or to make minor field alterations to an existing panel program. It is recom-
mended that the panel be uploaded to NAPCO's PCD-Windows software following any keypad programming and that
the PCD-Windows's error-check feature be utilized to reduce the possibility of programming omissions or conflicts.
3
Keep the Keypad Programming Worksheets on file for future reference.
General Programming Steps
!1. Contact the central station to ascertain receiver format, data format, event codes, subscriber numbers and tele-
phone number(s).
!2. Select the desired features by circling #the respective “address” boxes. Refer to the Programming Options
and Worksheets for guidance in selecting the “data” to be entered into those boxes.
!3. Program the data entered in the boxes on the worksheets into the respective addresses. The display will show
the entry numerically, but if hexadecimal format will display “0” for the number 10, and letters “B”, “C”, “D”, “E”, and
“F” for the numbers 11 through 15, respectively. To program a 10, press G0. To program 11 through
15, press G1through G5, respectively.
The displays will appear after a brief delay.
!Use Rto toggle the cursor between the 4-digit address field and the data entry locations.
!Enter the address directly using the number buttons.
!The contents of the address will be read automatically, along with the feature name and programming information.
The cursor will advance to the data field. Enter the required data directly using the number buttons.
!IMPORTANT: Press Uor Dto save the contents of each address.
EXIT DIRECT ADDRESS PROGRAM MODE: When done, press Cto exit and resume normal keypad operation.

LNAPCO Security Systems XGEM-P816 Programming Instructions
!
Page 15WI995C 2/04
SYSTEM DELAYS & TIMEOUTS (ADDRESS 0000 TO 0002, 0711, 0715 & 1059)
Direct Address Program Mode
WARNING: Timers have uncertainty of +/-1 sec, so a "time" of 1 second may actually timeout IMMEDIATELY.
!Select delay/timeout (0-255 sec.) from the table shown.
EXIT/ENTRY DELAYS: Apply only to zones programmed with the following options “Exit/Entry 1, Exit/Entry
2, Exit/Entry Follower”. For UL Installations, the maximum exit delay is 60 seconds and the maximum entry
delay is 45 seconds. NOTE: Sensor Watch Time Options are similar to above table, except in hours.
!Press Uor Dto save.
SYSTEM DELAYS & TIMEOUTS (ADDRESS 0716 & 0717)
DEFAULTS: The defaults shown on this
page and on the following pages are
automatically set after exiting the Easy
Menu Driven Mode.
EXIT ADDRESS 0000
DELAY
(sec.)
[Default = 060]
ENTRY ADDRESS 0001
DELAY 1
(sec.)
[Default = 030]
PGM2 Output ADDRESS 0711
Access Cntrl
Timeout (sec.)
[Default = 0 sec. = blank (•)]
ABORT ADDRESS 0715
DELAY
(sec.)
[Default = 030]
Sensor Watch ADDRESS 1059
Time
(Hrs.)
[Default = 024]
Report Cancel ADDRESS 1179
Window
(min.)
[Default = 0 sec. = blank (•)]
See Maximum Program Time
table (at left)
ENTRY ADDRESS 0002
DELAY 2
(sec.)
[Default = 030]
Maximum Program Time
Address Units Max Prog Time
1179 VERSION 10 - MIN
VERSION 9A - SEC
VERSION 10 - 254 MIN
VERSION 9A - 254 SEC
!1. Enter delay/timeout in corresponding address locations above.
Note: All entries for address 0716 are in quarter seconds (.25 seconds).
Therefore, the default of 008 results in a 2 second timeout.
!2. Press Uor Dto save.
AC Fail ADDRESS 0717
Report Delay
(min.)
[Default = 060]
CHIME ADDRESS 0716
TIMEOUT
(¼sec.)
[Default = 008 x ¼ sec. = 2 sec.]

XGEM-P816 Programming Instructions LNAPCO Security Systems
!Page 16 WI995C 2/04
SYSTEM OUTPUT TIMEOUTS (ADDRESS 0710, 0712, 0713 & 0714)
!1. Select delay/timeout (0-255 min.) from the table shown.
!2. Enter in corresponding address locations above.
!3. Press Uor Dto save.
OUTPUT TIMEOUTS: If a timeout of “0 min.” is selected, then the output will remain active (ON)
until the system is reset or disarmed. For UL Residential Installations, the minimum timeout is 4
minutes. Not UL listed for Commercial Installations.
DOWNLOAD/CALLBACK OPTIONS (ADDRESS 1183 & 0236-0255)
NUMBER OF RINGS BEFORE PICKUP: Enter the number of rings before automatic
pickup by the control panel when downloading from a computer (see Glossary at the back
for more information).
!1. Enter digit only.
!2. Valid entries are: 03-15. NOTE: Default is 15 Rings.
!3. Press Uor Dto save.
CALLBACK TELEPHONE NUMBER: Enter telephone number to be used when downloading from a computer (see Glossary at
the back for more information).
!1. Enter digit only.
!2. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•).
!3. Valid entries are: 1-9, B = *button, C = #button, D = 3 sec. pause, E = Wait for dial tone, F = ignore location.
!4. Press Uor Dto save.
PAGER FORMAT OPTIONS (ADDRESS 0256 & 0257)
LEADING DIGITS FOR PAGER FORMAT: In Pager Format reporting, the message typically begins with “00”.
However, for some pager services, this will cause the Pager's Voice Mail feature to activate. This option allows
you to program these digits to any number desired. A typical Pager report is “003 22 1234”, where 3 is the Event,
22 is the zone, and 1234 is the Subscriber ID number. For example, if the Leading Digits are programmed as “98”,
the Pager report will now appear as “983 22 1234”. NOTE: See CS Receiver Options to select Pager Format.
!1. Enter in 1st and 2nd Leading Digits as shown.
!2. Valid entries are: 0-9. Press Uor Dto save.
Callback
Telephone
ADDRESS 0236-0255 (RIGHT DIGITS 1-20)
0236 0237 0238 0239 0240 0241 0242 0243 0244 0245 0246 0247 0248 0249 0250 0251 0252 0253 0254 0255
(Digits 1-20)
[Default = blank (•) for all digits 1-20]
PGM2 ADDRESS 0710
Output
Timeout (min.)
[Default = 0 min. = blank (•)]
Alarm ADDRESS 0712
Output
Timeout (min.)
[Default = 015]
Pulse Alarm ADDRESS 0713
Output
Timeout (min.)
[Default = 015]
PGM1 ADDRESS 0714
Output
Timeout (min.)
[Default = 0 min. = blank (•)]
DELAY/
TIMEOUT
blank (•) 0 min.
1 1 min.
2 2 min.
3 3 min.
4 4 min.
5 5 min.
6 6 min.
16 16 min.
255 255 min.
DATA
ENTRIES
Leading Digits for ADDRESS 0256
Pager Format
(1st Digit)
Leading Digits for ADDRESS 0257
Pager Format
(2nd Digit)
[Default = blank (•) blank (•)]
Direct Address Program Mode
No. Rings ADDRESS 1183
Before
Pickup
[Default = 015 ]

LNAPCO Security Systems XGEM-P816 Programming Instructions
!
Page 17WI995C 2/04
GLOBAL SYSTEM EVENT/TROUBLE
SYSTEM RESPONSE
ACTIVATED BY GLOBAL
EVENT/TROUBLE
ADDR TEST
TIMER
TELCO
FAILURE
RF RCVR.
TROUBLE
MEMORY
FAILURE
LOW
BATTERY AC FAIL EZM TAMPER
Bell
Superv
1 2 3 4 5 6 7 8
Alarm Output 0460
Pulsed Alarm Output 0461
PGM1 Output 0462
PGM2 Output 0463
Report Event Telco 1 0464
Report Restore Telco 1 0465
Report Event Telco 3 0468
Report Restore Telco 3 0469
SYSTEM OPTIONS (ADDRESS 0460-0485 & 1054)
!1. Select the desired option entering the option number (1-8) for each digit.
!2. Enter corresponding option number in address location.
!NOTE: Dark shaded data value box shows option not available. Press Uor Dto save.
GLOBAL AMBUSH CODE: It is the 2-digits entered immediately prior to the regular disarm code. If
“Enable Global Ambush Code” (Address 0720) is selected and Address 1054 is left blank (•), then the
2-digit Global Ambush Code is “99”. If “Enable Global Ambush Code” is selected and Address 1054
is not left blank (•), then the 2-digit Global Ambush Code is the two digits entered in address 1054.
!Enter in address location (both 1st and 2nd digits); valid entries are 1-9. 3. Press Uor Dto
save.
Direct Address Program Mode
[Default = blank (•) blank (•)]
Global 1st digit 2nd digit
Ambush Code
ADDRESS 1054
SYSTEM RESPONSE
ACTIVATED BY AREA 1
EVENT/TROUBLE
AREA 1 SYSTEM EVENT/TROUBLE
ADDR AMBUSH KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX. * KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE Keyfob
Low Batt
1 2 3 4 5 6 7 8
Pulsed Alarm Output 0470
Alarm Output 0471
PGM1 Output 0472
PGM2 Output 0474
Report Event Telco 1 0475
Report Event Telco 3 0477
[Default = blank (•) from address 0470-0477] * NOTE: Keypad Aux. is not to be selected for UL Installations.
SYSTEM RESPONSE
ACTIVATED BY AREA 2
EVENT/TROUBLE
AREA 2 SYSTEM EVENT/TROUBLE
ADDR AMBUSH KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX. * KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE Keyfob
Low Batt
1 2 3 4 5 6 7 8
Pulsed Alarm Output 0478
Alarm Output 0479
PGM1 Output 0480
PGM2 Output 0482
Report Event Telco 1 0483
Report Event Telco 3 0485
[Default = blank (•) blank (•) from address 0478-0485] * NOTE: Keypad Aux. is not to be selected for UL Installations.
[Default = blank (•) from address 0460-0469]. Note: If Test Timer is enabled (above), Digital Dialer Test is also enabled.

XGEM-P816 Programming Instructions LNAPCO Security Systems
!Page 18 WI995C 2/04
SYSTEM OPTIONS (ADDRESS 0718-0722, 1060-1062)
*NOTE: Address 0721: Default depends on Easy Menu Question :“EZ
ZONE DOUBLING? Y/N”. If yes, then [Default = 1]. If no, then [Default =
blank (•)].
**NOTE: To select “Line-Fault Test only when Armed”, you must also se-
lect “Enable Line-Fault Test” at address 0721.
*** NOTE: If “Enable Global Ambush Code” in Address 0720 is selected, then
program the 2-digit “Global Ambush Code” in Address 1054. If Address
1054 is left blank (•), then, the 2-digit “Global Ambush Code” will be “99”.
0718 System Options 0719
Default
Option Default Option
OFF 1 Opening Report Only after Alarm Report OFF 1 Auto Bell Test on Arming
OFF 2 Closing Report Only on Conditional Close OFF 2 Auto Reset after Burglary Output Timeout
OFF 3 Incl. Sel./Grp. Bypass in Cond. Close /Status OFF 3 Suppress Bypass Reminder when Armed
OFF 4 Status Report OFF 4 Enable Local Alarm on First Zone AND Trip
OFF 5 Reserved OFF 5 Access Control on PGM2 Output
OFF 6 Enable AutoArm if not closed at end of Window OFF 6 Maintained Keyswitch Arming
OFF 7 Enable Time/Date KP Display OFF 7 Enable Manager's Mode
OFF 8 Disable Zone Fault Scrolling OFF 8 Disable Keypad Instant Mode
System Options
0720 System Options 0721 System Options
Default Option Default* Option
OFF 1 Interior Normally Bypassed OFF* 1 Enable Zone Doubling (Zones 9-16)
OFF 2 Enable Global Ambush Code *** OFF* 2 Wireless Trouble Activates Telco 1
OFF 3 Reset Day Zone with Arm/Disarm Only OFF* 3 Wireless Trouble Activates Telco 3
OFF 4 Enable Residential Fire OFF* 4 Enable Alarm Output on Telco Fail only when Armed
OFF 5 Disable Keypad Function Mode Download OFF* 5 Line-Fault Test only when Armed**
OFF 6 Disable Callback Download OFF* 6 Enable Line-Fault Test**
OFF 7 Chirp Output on Keyfob Arm/Disarm OFF* 7 Inhibit System Trouble Audible at Keypad †
OFF 8 Change Pulse Output to Temporal Output§OFF* 8 Select Alarm Output for Keyfob Chirp
† NOTE: Not for UL Installations.
§This feature must be programmed in Fire Alarm applications.
1060
Default Option
OFF 1 Enable Keypad Set Time/Date Message
OFF 2 Enable Cancel Report to Telco 3
OFF 3 Disable [ON/OFF] as Easy Exit
OFF 4 Enable GEM-PRINT Module
OFF 5 RESERVED
OFF 6 RESERVED
OFF 7 Disable System Trouble Audible Timeout
OFF 8 RESERVED
System Options
0722
Default Option
OFF 1 Automatic Interior Bypass/Easy Exit
OFF 2 Veri-phone Zones Trip PGM2 Output
OFF 3 Veri-phone Audio Priority Over Alarms
OFF 4 Resound on Wireless Smoke Low Battery
OFF 5 Don't Clear PGM2 Output with Disarm
OFF 6 Disable 2nd Call Ans. Machine Override
OFF 7 RESERVED
OFF 8 RESERVED
System Options
ADDRESS 1061: LUG E15 OUTPUT MODE
Select the options available from the table above.
!1. Enter digit only.
!2. Valid entries are “blank (•)” or “4”. Press Uor Dto save.
1061 Lug E15 Output Mode
DATA ENTRIES OPTION
blank (•) Armed
4 Armed Area 1 Away
Direct Address Program Mode
1062
Default Option
OFF 1 Exit Time Restart
OFF 2 Sound Alarm On Exit Error
OFF 3 Rpt Exit Err/Recent Close
OFF 4 Enable CP-01 Limits
OFF 5 Digital Dialer Rpt Enter /Exit Test Mode
OFF 6 Disable Call Waiting on 1st Attempt
OFF 7 RESERVED
OFF 8 RESERVED
System Options

LNAPCO Security Systems XGEM-P816 Programming Instructions
!
Page 19WI995C 2/04
Direct Address Program Mode
NOTE: * See Pager Format Options to program
Leading Digits for Pager Format.
CS RECEIVER OPTIONS (ADDRESS 0170-0191, 0192-0213, 0214-0235)
Default for CS Receiver 1 Format depends on Easy Menu Question “RCVR FORMAT”. [Default = •(blank) •
(blank)] for CS Receivers 2 and 3 Formats.
CS RECEIVER FORMATS: Up to 3 CS Formats may be programmed.
!1. Select the desired CS Receiver Format from the table shown.
!2. Enter the corresponding digit in the address location for each CS Receiver. NOTE:
Dark
shaded data value box shows option not available. Press [Enter] of [ON/OFF] to save.
DATA
ENTRY
CS RECEIVER 1 FORMAT
blank (•) Ademco Slow, Silent Knight Slow
2 Radionics Fast
3 Silent Knight Fast
4 Radionics, DCI, Franklin Slow
5 Universal High Speed
B SIA
C Ademco Point ID
E Pager *
CS RECEIVER OPTIONS:
Select options for any of the three CS Receivers.
!1. Select the desired option entering the option number
(1-8) for each digit.
!2. Enter corresponding option number in address
location.
NOTE: Dark shaded data value box shows option not avail-
able. Press [Enter] or ON/OFF] to save.
*NOTE: If both are selected, 1400Hz
has priority over 2300Hz.
CS RECEIVER TELEPHONE NUMBERS: Enter telephone numbers for any of the three CS Receivers (Telco 1, 2 & 3).
!1. Enter digit only.
!2. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•). Press [Enter] or [ON/OFF] to save.
!3. Valid entries are: 1-9, B = *button, C = #button, D = 3 sec. pause, E = Wait for dial tone, F = ignore location
Default for CS
Receiver 1 Tele-
phone Number
depends on Easy
Menu Question
“CENTRAL
PHONE #”.
[Default = blank (•)]
across digits 1-20
for CS Receiver
Telephone Num-
bers 2 and 3.
ADDRESS 0170
CS Receiver 1
Format
ADDRESS 0192
CS Receiver 2
Format
ADDRESS 0214
CS Receiver 3
Format
ADDRESS 0172-0191 (RIGHT DIGITS 1-20)
0172 0173 0174 0175 0176 0177 0178 0179 0180 0181 0182 0183 0184 0185 0186 0187 0188 0189 0190 0191
(Digits 1-20)
CS Receiver 1
Telephone
number
CS Receiver 2
Telephone
Number
ADDRESS 0194-0213 (RIGHT DIGITS 1-20)
0194 0195 0196 0197 0198 0199 0200 0201 0202 0203 0204 0205 0206 0207 0208 0209 0210 0211 0212 0213
(Digits 1-20)
CS Receiver 3
Telephone
Number
ADDRESS 0216-0235 (RIGHT DIGITS 1-20)
0216 0217 0218 0219 0220 0221 0222 0223 0224 0225 0226 0227 0228 0229 0230 0231 0232 0233 0234 0235
(Digits 1-20)
0171 CS Receiver Options 0193
Default Option Default Option
OFF 1 1400Hz Handshake/Kissoff * OFF 1 1400Hz Handshake/Kissoff *
OFF 2 2300Hz Handshake/Kissoff * OFF 2 2300Hz Handshake/Kissoff *
OFF 3 Enable Zone Number on Pulse Alarm OFF 3 Enable Zone Number on Pulse Alarm
OFF 4 Single Digit Only OFF 4 Single Digit Only
OFF 5 Sum Check OFF 5 Sum Check
OFF 6 3/1 with Extended Restores OFF 6 3/1 with Extended Restores
OFF 7 RESERVED OFF 7 RESERVED
OFF 8 RESERVED OFF 8 RESERVED
CS Receiver 2 Options
0215
Default Option
OFF 1 1400Hz Handshake/Kissoff *
OFF 2 2300Hz Handshake/Kissoff *
OFF 3 Enable Zone Number on Pulse Alarm
OFF 4 Single Digit Only
OFF 5 Sum Check
OFF 6 3/1 with Extended Restores
OFF 7 RESERVED
OFF 8 RESERVED
CS Receiver 3 Options

XGEM-P816 Programming Instructions LNAPCO Security Systems
!Page 20 WI995C 2/04
CS SUBSCRIBER ID & SYSTEM REPORTING OPTIONS (ADDRESS 0259-0350)
Default for CS Telco 1 Subscriber Event ID Number (Area 1) depends on Easy Menu Question “ACCOUNT #”. [Default = blank (•) blank (•) blank (•)
blank (•)] for all other ID Numbers.
CS TELCO SUBSCRIBER ID NUMBERS: Enter the Subscriber Opening/Closing and Event ID Numbers for any of the 3 CS Receivers.
!1. Enter 3 or 4 digits (depending on the CS receiver format) for each subscriber number from left to right.
NOTE: Leave trailing boxes blank (•).
!2. Valid entries are: 1-9, 0 and B-F. NOTE: A is not permitted. Press [Enter] or ON/OFF] to save.
CS SYSTEM REPORTING CODES:
1. Enter in corresponding address loca-
tion (left and right digits).
NOTE: Left digit is the first digit and
right digit is the second digit in a two
digit CS receiver format.
2. Valid entries are: 1-9, 0 and B-F.
NOTE: A is not permitted.
3. To disable a code leave boxes blank
(•).
NOTE: Dark shaded data value box
shows option not available.
4. Press Uor Dto save.
Direct Address Program Mode
* NOTE: Keypad Aux. is not to be selected for
UL Installations.
CS Telco 1 Sub-
scriber Event ID
Number (Area 1)
ADDRESS 0267-0270
(RIGHT DIGITS 1-4)
0267 0268 0269 0270
CS Telco 1 Sub-
scriber Opening/
Closing ID Number
(Area 1)
ADDRESS 0259-0262
(RIGHT DIGITS 1-4)
0259 0260 0261 0262
CS Telco 2 Sub-
scriber Event ID
Number (Area 1)
ADDRESS 0287-0290
(RIGHT DIGITS 1-4)
0287 0288 0289 0290
CS Telco 2 Sub-
scriber Opening/
Closing ID Number
(Area 1)
ADDRESS 0279-0282
(RIGHT DIGITS 1-4)
0279 0280 0281 0282
CS Telco 3 Sub-
scriber Event ID
Number (Area 1)
ADDRESS 0307-0310
(RIGHT DIGITS 1-4)
0307 0308 0309 0310
CS Telco 3 Sub-
scriber Opening/
Closing ID Number
(Area 1)
ADDRESS 0299-0302
(RIGHT DIGITS 1-4)
0299 0300 0301 0302
CS Telco 1 Sub-
scriber Event ID
Number (System)
ADDRESS 0275-0278
(RIGHT DIGITS 1-4)
0275 0276 0277 0278
CS Telco 2 Sub-
scriber Event ID
Number (System)
ADDRESS 0295-0298
(RIGHT DIGITS 1-4)
0295 0296 0297 0298
CS Telco 3 Sub-
scriber Event ID
Number (System)
ADDRESS 0315-0318
(RIGHT DIGITS 1-4)
0315 0316 0317 0318
[Default = blank (•) blank (•) from address 0319-0332]
[Default = blank (•) blank (•) from address 0333-0350]
CS SYSTEM REPORT-
ING CODES
ADDR
Alarm Restore blank (•) 0319
Trouble blank (•) 0320
Trouble Restore blank (•) 0321
Xmitter Low Battery blank (•) 0322
Xmitter Supervision blank (•) 0323
Xmitter Tamper blank (•) 0324
RESERVED blank (•) 0325 blank (•)
Opening blank (•) 0326
Closing blank (•) 0327
Opening after Alarm blank (•) 0328
Conditional Close blank (•) 0329
Cancel blank (•) 0330
Test Timer blank (•) 0332
ADDRESS 0319-0332 CS SYSTEM REPORTING
CODES
ADDR
Telco Fail 0333
RF Rec. Trouble 0334
Memory Fail 0335
Low Battery 0336
Panel AC Fail 0337
EZM Tamper 0338
Alarm Output Superv. 0339 bl
Ambush 0340
Panic 0341
Fire 0342
Auxiliary * 0343
Tamper 0344
Fail to Open 0345
Fail to Close 0346
Keyfob Low Battery 0347
Exit Error 0348
Recent Close 0349
Fault Find 0350
ADDRESS 0333-0350