NAPCO Gemini GEM-P1664EX Installation manual

HARDWIRE WIRELESS
GEM-P1664EX
CONTROL PANEL/COMMUNICATOR
Programming the GEM-P1664EX Control Panel with the
"Classic" GEM-RP1CAe2 Keypad and the "K Series" GEM-K1CA Keypad
WI1386 5/05© NAPCO 2005
Quick Start (for "Classic" GEM-RP1CAe2)
1. Refer to the wiring diagram, connect Siren, Aux. Power,
PGM Output, Remote Bus, Earth ground, Zone and Tele-
phone wiring. NOTE: See Installation Instructions
(WI1388).
2. Connect AC power first and then the battery.
3. Configure the keypad (see page 42).
4. Access the Easy Menu Driven (Dealer Program) Mode:
Press 456789 A
Press NO (g) until “ACTIVATE PROGRAM Y/N” appears on the
keypad display.
Press YES (F) to Enter Dealer Program Mode. Go to page 5.
Dealer Code
Quick Start (for "K-Series" GEM-K1CA)
1. Refer to the wiring diagram, connect Siren, Aux. Power,
PGM Output, Remote Bus, Earth ground, Zone and Tele-
phone wiring. NOTE: See Installation Instructions
(WI1388).
2. Connect AC power first and then the battery.
3. Configure the keypad (see page 42).
4. Access the Easy Menu Driven (Dealer Program) Mode:
Press 456789 R
Press NO (Q) until “ACTIVATE PROGRAM Y/N” appears on the
keypad display.
Press YES (P) to Enter Dealer Program Mode. Go to page 5.
Dealer Code
"K Series" GEM-K1CA
GEMINI
SYSTEM READY
01/01/05 12:00 AM
ARMED
COMPUTERIZED SECURITY SYSTEM
STATUS
R123
B456
C7890
U
NEXT/YES
P
PRIOR/NO
Q
AREA
G
PROGRAMMING
INSTRUCTIONS
R
"Classic" GEM-RP1CAe2
GEMINI
SYSTEM READY
01/01/05 12:00 AM
ARMED
COMPUTERIZED SECURITY SYSTEM
STATUS
A123
B456
C7890
D
NEXT/YES
E
PRIOR/NO
F
AREA
G
Publicly traded on NASDAQ Symbol: NSSC

THIS MANUAL INCLUDES FEATURES WHICH ARE ONLY AVAILABLE IN
CONTROL PANEL FIRMWARE VERSION 1.0 OR LATER.
NAPCO Security Systems, Inc.
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, call toll free: [phone]
For direct line to Technical Service, call toll free: [phone]
Internet: http://www.napcosecurity.com
IMPORTANT NOTE
This manual supports the keypad programming of the GEM-P1664EX control panel with the NAPCO "classic" GEM-
RP1CAe2 keypad as well as the GEM-K1CA "K Series" keypad. The new "K Series" GEM-K1CA model offers the new
STAY and AWAY buttons with simplified functionality, along with the new MENU and ENTER buttons.
While the instructions in this manual are depicted using the GEM-K1CA keypad, the manual applies to both the "classic"
and the "K Series" keypads.
Program Mode is the same for both keypads--only the button names have changed, as follows:
•The Abutton and the Rbutton operate identically (in Program Mode) for both keypads.
•The Dbutton and the Ubutton operate identically (in Program Mode) for both keypads.
•The button and the button operate identically (in Program Mode) for both keypads. The words
"NEXT/YES button" are used in this manual.
•The button and the button operate identically (in Program Mode) for both keypads. The words
"PRIOR/NO button" are used in this manual.
For consistency, it is recommended that all keypads either be all "classic" or all "K Series"--both keypad
types should not be used in one alarm system.

LNAPCO Security Systems XGEM-P1664EX Programming Instructions

Page 3
WI1386 5/05
TABLE OF CONTENTS
Refer to accompanying GEM-P1664EX Installation Instructions (WI1388) for installation information.
SYSTEM PROGRAMMING OPTIONS ............................ 4
INTRODUCTION......................................................... 4
DOWNLOADING FROM A COMPUTER .................... 4
EASY MENU DRIVEN PROGRAM MODE ...................... 5
Dealer Program - Preliminary Information................... 5
Accessing Dealer Program Mode................................ 5
Customizing a Default Program .................................. 5
GEM-RP1CAe2/GEM-K1CA Easy Program Menu 6
Total Number of Zones in Area 1 ........................ 6
Panel Zone Doubling ........................................... 6
Fire Zones in Area 1 ............................................ 6
2-Wire Fire Zones in Area 1 ................................ 6
Local or Central Station Reporting System ......... 6
Exit/Entry Zones in Area 1................................... 6
Interior Zones in Area 1 ....................................... 6
24 Hour Zones in Area 1 ..................................... 6
Chime Zones in Area 1........................................ 7
Chime 2 Zones in Area 1..................................... 7
Exit/Entry2 Zones in Area 1................................. 7
50 mS Loop Response Zones............................. 7
Aux Output Activated on Alarm Zones ................ 7
Sensor Watch Zones .......................................... 7
Keypad Sounder On Alarm Zones....................... 7
Auto Bypass Re-entry Zones............................... 7
Enable No EOLR Zones ...................................... 7
Enable Telco Line Fault Test?............................. 7
Enable Burg Output Chirp on KeyFob? ............... 8
Enable SIA CP-01 Features? .............................. 8
Number of Keypads in Area 1 ............................ 8
Central Station Receiver 1 Telephone Number... 8
Central Station Receiver 1 Account Number....... 8
Central Station Receiver 1 Format ...................... 8
Enter User Codes ............................................... 8
RF Transmitter Points.......................................... 9
Key Fob Transmitters as Arm/Disarm & Control De-
vices.............................................................. 9
Key Fob Transmitters as Zone Input Devices .... 10
Enter Zone Descriptions ...................................... 10
Enter Date ........................................................... 10
Enter Time ........................................................... 10
Dealer Code ........................................................ 10
Test Timer ........................................................... 10
Clear Dealer Program.......................................... 10
Cold Start............................................................. 10
DIRECT ADDRESS PROGRAM MODE.......................... 11
Direct Address Overview............................................. 11
Address Mode Displays............................................... 11
Binary (Bit) Format............................................. 11
Decimal Format.................................................. 12
Hexadecimal Format.......................................... 13
Programming Conventions Used in this Manual ......... 14
SYSTEM DELAYS & TIMEOUTS .............................. 15
SYSTEM OUTPUT TIMEOUTS ................................. 16
DOWNLOAD/CALLBACK OPTIONS ......................... 16
SYSTEM OPTIONS .................................................... 17
CS RECEIVER OPTIONS .......................................... 20
CS SUBSCRIBER ID OPTIONS ................................ 21
CS SYSTEM REPORTING OPTIONS ....................... 22
CS AREA & SYSTEM REPORTING OPTIONS ......... 22
ZONE ANDING TIME WINDOW ................................ 23
KEYPAD UNBLANKING TIME WINDOW .................. 23
CLOCK ADJUSTMENTS .......................................... 23
CS ZONE REPORTING OPTIONS ............................ 24
CS USER REPORTING OPTIONS ............................ 25
EZM GROUP OPTIONS ............................................ 26
AREA BELL CONTROL OPTIONS ............................ 27
KEYPAD OPTIONS ................................................... 28
TEMPERATURE DISPLAY AT KEYPAD ................... 29
AREA ARMING OPTIONS ......................................... 30
ZONE RESPONSE TIME............................................ 30
ZONE OPTIONS - ZONES 1 TO 16 .......................... 31
ZONE OPTIONS - ZONES 17 TO 32 ........................ 32
ZONE OPTIONS - ZONES 33 TO 48 ........................ 33
ZONE OPTIONS - ZONES 49 TO 64 ........................ 34
EXTERNAL RELAY CONTROL ................................. 35
RF RECEIVER & SUPERVISORY TIMER OPTIONS 38
CLEAR PROGRAM OPTIONS .................................. 39
USER PROGRAM MODE................................................ 39
Preliminary Information ............................................... 39
Accessing User Program Mode .................................. 40
User Codes ................................................................. 40
Zone Descriptions ....................................................... 41
Date............................................................................. 41
Time ............................................................................ 41
KEYPAD CONFIGURATION MODE ............................... 42
Keypad Installation...................................................... 42
Configuring the Keypads............................................. 42
EASY MENU PROGRAMMING WORKSHEETS ............ 44
ALPHABETICAL INDEX ................................................. 48
ADDRESS NUMBER INDEX ........................................... 53
GEM-P1664EX WIRING DIAGRAM ................................ 60

XGEM-P1664EX Programming Instructions LNAPCO Security Systems

Page 4 WI1386 5/05
SYSTEM PROGRAMMING OPTIONS
INTRODUCTION
The GEM-P1664EX control panel may be programmed by various means, each of which will be covered in detail in the
sections that follow. Keypad displays shown are for a GEM-RP1CAe2/K1CA (version 8 keypad), the recommended key-
pad for programming. For Programming Instructions with the GEM-RP2ASe2/GEM-K2AS, GEM-RP3DGTL/GEM-
K3DGTL and the GEM-RP4RFC/GEM-K4RF series, see WI1387.
Downloading From a Computer. This is the preferred method of programming. The panel may be
downloaded from (or uploaded to) an IBM PC-compatible computer, either locally or remotely. Napco's PCD3000
Quickloader software features context-sensitive help screens as well as an error-checking utility that prevents pro-
gramming of incompatible or conflicting data to ensure proper panel operation.
Easy Menu-Driven Program (Dealer Program) Mode - Keypad Programming. The Easy Menu-Driven
Program Mode allows keypad programming of number of zones in area 1, panel zone doubling, number of fire zones
(both 4-wire and 2-wire), local or Central Station reporting, number of exit/entry zones, number of interior zones, num-
ber of 24 hour zones, number of chime zones, Chime 2 zones, Exit/Entry2 zones, 50ms loop response zones, aux out-
put activated on alarm zones, sensor watch zones, keypad sounder on alarm zones, auto bypass re-entry zones,
EOLR zones, number of keypads in area 1, Central Station telephone number, Central Station account number, Cen-
tral Station receiver format, User Codes, RF transmitter points, RF keyfob transmitters, zone descriptions, date/time,
dealer code, Test Timer, Telco line fault test, Burg output chirp on keyfob, keypad time/date display, enable CP-01 pro-
gramming, and clear dealer program/cold start. For new panels, a custom default program may be created at the key-
pad. A menu-driven utility prompts the installer to configure the system. Further detailed customization is accom-
plished in the Direct Address Program Mode.
Direct Address (Dealer Program) Program Mode - Keypad Programming. The Direct Address Pro-
gram Mode is an extension of the Dealer Program Mode wherein data is entered at the keypad by location. This
mode is accessed from the Easy Menu Driven Program Mode by pressing the Cbutton at any time.
User Program Mode - Keypad Programming. The User Program Mode is intended for authorized users
and is limited to keypad programming of User Codes, Time, Date and Zone Descriptions.
DOWNLOADING FROM A COMPUTER
The control-panel program may be downloaded from the computer by any of the following methods.
Local Downloading
(Note: This procedure should be used after installation, after peripheral devices are connected).
For direct high-speed data transfer to the control panel from a desktop computer, connect the download jack (JP2)
on the panel to the LOCAL jack (J3) on the Napco PCI2000/3000 computer interface using the supplied 6-
conductor cable. (Refer to PCI2000/3000 Installation Instructions WI443 for wiring diagram and procedures).
Similarly, a high-speed local download may be made in the field using a notebook or laptop computer. Connect
JP2 on the control panel to a Napco PCI-MINI computer interface using the 6-conductor cable supplied. (Refer to
PCI-MINI Installation Instructions WI767).
Remote Downloading
(Also see PCI2000/3000 Installation Instructions WI443).
Function Mode
Start by establishing a telco connection between the computer operator and the installer. During this procedure,
voice contact will be lost, therefore both the installer and the computer operator should be familiar with the opera-
tion. When a steady high-pitched tone is heard at the site phone, access the “ACTIVATE DOWNLOAD” Function (see
Keypad Programming Modes), then press the Jor Ubutton or the NEXT/YES button; the site phone will go dead.
Hang up the phone and wait for a call from the central station confirming a successful download.
Callback Method
An installed, unattended panel may be programmed or reprogrammed remotely using the Callback-Method
Download feature of the PCD3000 software. Remote downloading requires a modem compatible with the
PCI2000/3000. Upon answering the call from the computer, the panel will verify the Download Security Code and,
if confirmed, will establish a connection. If a Callback Number is programmed into the panel, the panel will auto-
matically disconnect and call the computer at this number before establishing a connection.

LNAPCO Security Systems XGEM-P1664EX Programming Instructions

Page 5
WI1386 5/05
EASY MENU DRIVEN PROGRAM MODE
DEALER PROGRAM - PRELIMINARY INFORMATION
The Default Dealer Code is 456789. Use this code to enter the Dealer Program Mode
to program a custom Dealer Code, which replaces the Default Dealer Code. If you clear your Dealer Code, use the Default
Dealer Code once again to enter programming.
After entering codes or data, press the save Uor Dbutton. Data will not be stored into memory unless Uor Dis pressed.
If the keypad is in the Program Mode and no activity is detected for longer than 4 minutes, a steady tone will sound.
Silence the sounder by the Gbutton to continue, or by pressing the Cbutton to exit.
A panel that has been COLD STARTED (Address Location 2286) performs identically to a new panel.
When programming a Multiple Area System, Direct Address Programming Mode must be used to complete the program.
For ease of programming, it is recommended that a GEM-RP1CAe2 or GEM-K1CA be used. If a GEM-RP2ASe2/
GEM-K2AS is used, see WI1387.
1. Press 456789 R
2. Press PRIOR/NO button until “ACTIVATE PROGRAM Y/N”appears on LCD screen.
3. Press NEXT/YES button to Enter Dealer Program Mode.
4. Press CC to Exit Dealer Program Mode when finished.
Dealer Code (Default = 456789)
•Number of Zones in Area 1
•Panel Zone Doubling
•Fire Zones in Area 1
•2-Wire Fire Zones in Area 1
•Local or Central Station Reporting System
•Exit/Entry Zones in Area 1
•Interior Zones in Area 1
•24 Hour Zones in Area 1
•Chime Zones in Area 1
•Chime 2 Zones in Area 1
•Exit/Entry2 Zones in Area 1
•50mS Loop Response Zones
•Aux Output Activated on Alarm Zones
•Sensor Watch Zones
•Keypad Sounder on Alarm Zones
•Auto Bypass re-entry Zones
•Enable no EOLR Zones
•Enable Telco Line Fault Test
•Enable Burg Output Chirp on Keyfob
•Enable CP-01 Programming
•Number of Keypads in Area 1
•Central Station Receiver 1 Tel. Number
•Central Station Receiver 1 Account Number
•Central Station Receiver 1 Format
•Enter User Codes
•RF Transmitter Points
•Quick "Enroll" Method
•Key Fob Transmitters
•Enter Zone Descriptions
•Enter Date
•Enter Time
•Dealer Code
•Test Timer
NEW PANELS: The custom default program may be created for new panels only. Once the panel has been programmed by any
means, the number zones will be suppressed and cannot be changed. Should it be necessary to create a new custom default pro-
gram, (a) from the Dealer Program Mode, press the Cbutton to enter the Direct Address Program Mode; (b) access Location
2285 (Clear Program); (c) press the Uor Dbutton and start over.
EASY MENU DRIVEN PROGRAM MODE
This procedure will automatically set up system keypads, EZMs, wireless transmitters, etc. After your basic default program has
been loaded, you may alter it as necessary in the Direct Address Program Mode.
ACCESSING DEALER PROGRAM MODE
CUSTOMIZING A DEFAULT PROGRAM
For new panels, you can design a default program that will best suit your application. Using this procedure, you will configure the panel for:

XGEM-P1664EX Programming Instructions LNAPCO Security Systems

Page 6 WI1386 5/05
GEM-RP1CAe2/GEM-K1CA Keypad Easy Program Menu
To create a custom program using the GEM-RP1CAe2/GEM-K1CA keypad, simply answer the following questions and record
your information on the Easy Menu Programming Worksheet. In each of the following steps, press Rto set cursor, the
NEXT/YES button to go forwards, the PRIOR/NO button to go backwards, Uor Dto save and Ctwice to exit at any time.
Total Number of Zones in Area 1 (New Program Only)
•Enter the total number of zones to be programmed for Area 1.
•Valid entries are from 01 to 64. Directly enter the total number of zones, including leading zeros.
•The system is based on groups of 4 zones each (after the first 8 zones), and will automatically
round up to the next group of 4. For example, if you enter 18, it will automatically convert this to
20 zones. Press Uto save. Press the NEXT/YES button to proceed.
Panel Zone Doubling (New Program Only)
•To double the number of hardwired panel zones from 8 to 16, press YES.
•If Panel Zone doubling is not desired, press the PRIOR/NO button.
•The 16 zones will remain EOL terminated zones, requiring Normally Closed devices only.
•Refer to Wiring Diagram and Installation Instructions for wiring instructions
Fire Zones in Area 1 (New Program Only)
•Enter the zone number of any Fire Zones (including 2-wire, 4-wire or wireless).
•Valid entries are from 01 to 64.
•Directly enter each zone number, including leading zeros, and press Uto save, and then re-
peat for any additional zone(s). Press the NEXT/YES button to proceed.
2-Wire Fire Zones in Area 1 (New Program Only)
•Enter the zone number of any Fire Zone (from previous question) to be used with 2-wire
smoke detectors.
•Valid entries are 07 and 08. Directly enter each zone number, including leading zeros.
•Press Uto save, and repeat for any additional zone(s); press NEXT/YES to proceed.
NOTE: Only zones which have been designated as Fire Zones can be programmed as 2 Wire
Fire zones. JP3 must be set to “2-WF” position for 2-wire fire. (refer to Installation Instructions).
Local or Central Station Reporting System (New Program Only)
Press the NEXT/YES button for all zones to report; press the PRIOR/NO button for local system
Exit/Entry Zones in Area 1 (New Program Only)
•Enter the zone numbers of zones to be used as Exit/Entry zones.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.
NOTE: Exit/Entry Entry time of 30 seconds will automatically be programmed.
Interior Zones in Area 1 (New Program Only)
•Enter the zone numbers to be used as Interior Zones.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s).
•Press the NEXT/YES button to proceed.
•All Interior zones will also be automatically programmed as “Exit/Entry Follower” and as
"Power Up Delay" zones.
24 Hour Zones in Area 1 (New Program Only)
•Enter the zone numbers of zones to be used as 24 Hour zones.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.
NOTE: 24 Hour Zones will automatically be programmed as audible (Burg Output).
EASY MENU DRIVEN PROGRAM MODE
(Direct Entry)
#of Zns in Area1
Enter # Zones XX
(Press YES or NO)
EZ Zone Doubling
Enabled? Y/N
(Direct Entry)
Fire Zones
Enter Zone # °°
(Direct Entry)
2-Wire Fire Zns
Enter Zone # °°
(Press YES or NO)
Report All Zones
To Central? Y/N
(Direct Entry)
Exit/Entry Zones
Enter Zone # XX
(Direct Entry)
Interior Zones
Enter Zone # XX
(Direct Entry)
24 Hour Zones
Enter Zone # °°

LNAPCO Security Systems XGEM-P1664EX Programming Instructions

Page 7
WI1386 5/05
EASY MENU DRIVEN PROGRAM MODE
Chime Zones in Area 1 (New Program Only)
•Enter the zone numbers which are to be used as Chime Zones.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), press the NEXT/YES button to proceed.
NOTE: A chime time of 2 seconds will be automatically programmed.
Chime 2 Zones in Area 1 (New Program Only)
•Enter the zone numbers which are to be used as Chime 2 Zones.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
NOTE: A chime time of 2 seconds will be automatically programmed.
Chime 2 zones give a distinct pulsating tone when zone is faulted.
Exit/Entry2 Zones in Area 1 (New Program Only)
•Enter the zone numbers of zones to be used as Exit/Entry zones.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.
NOTE: An Exit/Entry 2 Entry Time of 30 seconds will automatically be programmed.
50 mS Loop Response Zones (New Program Only)
•Enter the zone numbers of zones to be have a 50mS loop response.
•Valid entries are from 01 to 08. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
Note: Only panel zones 01-08 can be programmed for Quick Loop Response. All other zones can be
programmed via their respective EZM's (hardwire). Time can also be adjusted via address 2280.
Aux Output Activated on Alarm Zones (New Program Only)
•Enter the zone numbers of zones to activate the PGM2 upon alarm.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
NOTE: A PGM2 Timeout of 15 minutes will automatically be programmed.
Sensor Watch Zones (New Program Only)
•Enter the zone numbers of zones to be Sensor Watch zones.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
NOTE: A Sensor Watch Time of 24 hours will automatically be programmed.
Keypad Sounder On Alarm Zones (New Program Only)
•Enter the zone numbers of all zones to activate the Keypad Sounder upon alarm.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
Auto Bypass Re-entry Zones (New Program Only)
•Enter the zone numbers of zones to be Auto Bypass Re-entry zones.
•Valid entries are from 01 to 64. Directly enter each zone number, including leading zeros.
•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
•Auto Bypass Re-entry Zones allow the system to be armed with the zone faulted but come back into
the system (armed) when the zone is subsequently closed.
Enable No EOLR Zones (New Program Only)
•Press YES to program all zones except 24 Hr & fire zones for No End Of Line Resistor. Press NO to
continue.
Enable Telco Line Fault Test?
•Press YES to enable Telco Line Fault Test.
•Press NO to continue. NOTE: If enabled, a Telco Line Fault Test Delay of 60 sec. will auto-
matically be programmed.
(Direct Entry)
Chime Zones
Enter Zone # °°
(Direct Entry)
Chime 2 Zones
Enter Zone # °°
(Direct Entry)
Exit/Entry2 Zones
Enter Zone # °°
(Direct Entry)
50mS Loop Zones
Enter Zone # °°
(Direct Entry)
Aux Output Zones
Enter Zone # °°
(Direct Entry)
Sensor Watch Zns
Enter Zone # °°
(Direct Entry)
KP Sndr Alrm Zns
Enter Zone # °°
(Direct Entry)
Auto Byp REnt Zn
Enter Zone # °°
(Press YES or NO)
Enable No EOLR
Zones Y/N
(Press YES or NO)
Enable Telco
Line Test? Y/N

XGEM-P1664EX Programming Instructions LNAPCO Security Systems

Page 8 WI1386 5/05
EASY MENU DRIVEN PROGRAM MODE
Enable Burg Output Chirp on KeyFob?
•Press the NEXT/YES button to enable Burg Output Chirp on KeyFob Arm / Disarm.
•Press the PRIOR/NO button to continue.
NOTE: The Burg Output will chirp once on Keyfob Arm and twice on Keyfob Disarm.
Enable SIA CP-01 Features?
•Press the NEXT/YES button to enable.
•Press the PRIOR/NO button to continue.
The SIA CP-01 Features are designed to reduce the incidence of false alarms. NOTE: Do not
enable unless reporting, otherwise system trouble Fail to Communicate may occur.
Number of Keypads in Area 1
•Enter the total number of Keypads to be installed in Area 1.
•Valid entries are from 01 to 07. Directly enter the number of keypads, including leading zeros.
Press Uto save. Press the NEXT/YES button to proceed.
NOTE: Area 2-4 keypads must be assigned in Direct Address Programming. See Keypad Options.
Central Station Receiver 1 Telephone Number
•Enter telephone number of up to 16 digits.
•Press 1through 9for digits 1–9; G0for a zero and 0for a blank (•).
•Press G1through G5for letters B–F, respectively.
•Pre-Dial Delay = “D” (G4); Dial-Tone Detection = “E” (G5).
•Press Uto save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Ad-
dress Programming. See CS Receiver Options.
Central Station Receiver 1 Account Number
•Enter an account number of up to four digits.
•Press 0through 9for digits 0–9, and G0for a blank (•).
•Press Uto save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Account Numbers
must be entered in Direct Address Programming. See CS
Reporting Options.
Central Station Receiver 1 Format
•From the table at the right enter the receiver format.
•Press 0through 9, and G0 for blank (•).
•Press G1 through G4 for letters B–E.
•Press Uto save and press the NEXT/YES button to proceed.
Enter User Codes (Press Rto set cursor.)
For default program, enter up to 64 User Codes, with Area 1, 2, 3 & 4 Options.
•Press the (R) button once to set the cursor to the User Code.
•Press 0through 9to enter a code from 3 to 6 digits, leave blank (•) any trailing boxes.
•Press Rto set the cursor to the Area 1 Options Level. Refer to the table below for available op-
tions. For Area 2 Options, press the Rbutton once again. For Area 3 & 4 Options, press Ra third and fourth time.
•If “Enable Global Ambush Code” (Address 1422) is enabled and “Global Ambush Code” (Address 2045) is not left blank (•), do not program the
first two digits of ANY User Code the same as the “Global Ambush Code”. See Address 2045 further in this manual for more information.
•Press Uto save. Note: Duplicate User Codes are not allowed; therefore a duplicate Code entered in the LCD Window will erase when Uis
pressed. To proceed to the next User Code, press Rto set the cursor to the User Number and change it using the number buttons. Press
the NEXT/YES button to proceed.
(Direct Entry)
Central Phone #
(Direct Entry)
Central Station
Account # (____)
DATA
ENTRY
CS RECEIVER 1 FORMAT
•
(blank)
Ademco Slow, Silent Knight
Slow
2 Radionics Fast
3 Silent Knight Fast
4 Radionics, DCI, Franklin Slow
5 Universal High Speed
B SIA
C Ademco Point ID
E Pager
(Direct Entry)
See WI for Info
Rcvr Format (0)
Enter user code->
U01 123 - 9-
User# User Code Area 1 Area 2
Example: Program a code of “2222” for user
02, with area 1 options of “Arm/Disarm” and
“User Program”. Enter “2222” for a user code,
“• (blank) 9” for area 1 options and “• (blank) •
(blank)” for area 2 options.
(Direct Entry)
# Area 1 Keypads
Enter # KPs 01
(Press YES or NO)
Enable SIA CP-01?
Y/N
(Press YES or NO)
Enable Burg Out
Chirp? Y/N
USER AREA OPTIONS
DATA ENTRIES
L R
blank(•) blank(•) Disabled
blank(•) 1 Arm/Disarm
blank(•) 2 Arm Only
blank(•) 3 Service
blank(•) 4 Access
blank(•) 5 Ambush
blank(•) Add 8 * User Program
4 blank(•) Bypass Enable
OPTION
ENABLED
USER OPTIONS
USER CODE
(UP TO 6 DIGITS)
AREA 1
OPTIONS
AREA 2
OPTIONS
AREA 3
OPTIONS
AREA 4
OPTIONS

LNAPCO Security Systems XGEM-P1664EX Programming Instructions

Page 9
WI1386 5/05
EASY MENU DRIVEN PROGRAM MODE
RF Transmitter Points (Press Rto set cursor.)
For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)
•The zone number (01–64) to which the transmitter will be mapped.
•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•The point number (1–2); enter “9” for unsupervised (all points).
•Press Uto save and NEXT/YES button to proceed when all transmitters have been entered.
NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A = G0; B = G1;
C = G2; D = G3; E = G4and “F” = G5.
Quick "Enroll" Method: If a receiver is already installed in the panel, transmitter wireless
points can be programmed automatically (“enrolled”) using the following procedure. NOTE: The
transmitter point will be enrolled only if the signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be mapped.
2. Press Bto enter the Enroll Mode. The red and green LEDs on the keypad will flash and the
window will display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).
4. Install the transmitter battery. The keypad will beep to indicate that the point has been successfully
enrolled. Multi-point transmitters can be mapped to successive zones simultaneously.
Key Fob Transmitters as Arm/Disarm & Control Devices (Press Rto set cursor).
Key fobs can be programmed as “Arm/Disarm” devices using their On/Off buttons (refer to
WI752). For each Key Fob Transmitter, enter:
•The Key Fob Transmitter number (01–8).
•The area number to which transmitter is assigned (0 to disable keyfob, 1 through 4).
•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•The Aux 1 Option (see key fob aux 1 & aux 2 options).
•The Aux 2 Option (see key fob aux 1 & aux 2 options).
•Press Uto save and NEXT/YES button to proceed when all key fobs have been entered.
NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A = G0; B = G1;
C = G2; D = G3; E = G4and “F” = G5.
ZN# XMIT#+CS P
Zn01- 000000:0-0
Zone # Xmitter Check Point
Mapped to ID Sum #
ZN# XMIT#+CS P
Zn01- 000000:0-0
ZN# XMIT#+CS P
ZN01- ENROLL:A--
Example. A 2-point transmitter has the RF ID number 287613:1.
Map point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone “06”.
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that
one point has been programmed. (Transmitter 287613:1, point
1 will be mapped to Zone 6).
5. Enter Zone “09”.
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad
will beep once to indicate that one point has been programmed.
(Transmitter 287613:1, point 2 is mapped to Zone 9).
KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm
system, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the key
fob, the location where the person holding the key fob is stationed, or the special purpose of the key fob button being depressed.
See the next page on Key Fob Transmitters as Zone Input Devices .
KF A XMIT#+CS OP
01-0 000000:0 00
KF Area Xmitter Check Aux
# ID Sum 1&2
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above and press Uto save. Similarly, to
cancel a code, blank out each number of the code and press Uto save.
AREA OPTIONS EXPLANATION
Disabled User Code not active in this area.
Arm/Disarm Allows User Code to arm/disarm this area.
Arm Only Prevents User Code from disarming this area.
Service A Service Code has restricted arm/disarm rights; if an area is armed with a Service Code, a “MONITOR ON” appears on the GEM-RP2ASe2 keypad and the
area can be disarmed with any valid User Code, including a Service Code. If the area is armed with OTHER than a Service Code, it CANNOT be dis-
armed with a Service Code. This is typically used to allow tradesmen access to premises under control of the owner.
Access This is normally used to activate a door strike while an area is disarmed. Also program “Access Control on PGM2. Output” (Address 0719) and “PGM2
Output Access Control Timeout” (Address 0711).
* User Program User Program Option is enabled. To enable User Program Option for any user, add 8 to the data entry for Area Option (see example). Then, User Pro-
gramming can be performed at any Keypad by a user code with user program enabled.
Related User Options:“Enable Global Ambush Code” (Address 1422), “Global Ambush Code” (Address 2045) & “Enable Manager's Mode” (Address 1421).
Ambush There are two types of Ambush Codes: (1) A 2-digit code (prefix) that is entered immediately prior to (and as part of) the regular User Code and (2) A
separate and unique User Code. Disarming with an Ambush Code will cause a silent report to be sent to a central station. Thus, should a user be forced
to disarm, he can silently signal an emergency while appearing to be merely disarming the system.
Bypass Enable Security Bypass--Bypass is enabled only with a security code.

XGEM-P1664EX Programming Instructions LNAPCO Security Systems

Page 10 WI1386 5/05
Key Fob Transmitters as Zone Input Devices
(Refer to display above: press the PRIOR button to go backwards).
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button =
point 2; A1 = point 3; A2 = point 4. Up to 64 key fobs (using 1 button) or 32 key fobs (using 2 buttons) or
16 key fobs (using all 4 buttons) or any combination up to a maximum of 64 controlled zones can be as-
signed, providing multiple wireless panic buttons on a system, each reporting to a Central Station or a
pager and/or annunciating on a keypad the key fob zone number with a description. To assign a key fob
to a zone: program the key fob as you would a transmitter, entering the key fob's ID code, check sum and
point number at the appropriate zone. The “Quick Method” is not allowed. The zone may be hardwired to
an electrical sensor as well as assigned to a key fob (either one will activate the zone alarm output).
NOTE: If assigning a key fob to a zone, the “ON/OFF” buttons on the key fob will no longer arm/disarm the
system. The key fob is converted to a “panic only” device.
Enter Zone Descriptions
•For each zone, enter a description of up to two lines. Press Uto save each description.
•See page 41 for instructions for entering characters and numbers for the zone descriptions.
•To proceed to the next description, place the cursor under the Zone Number (e.g. “1”) and
press the number that corresponds to the zone. Program new description as above. NOTE: Zone Descriptions can only be en-
tered through the GEM-RP1CAe2 Keypad or by using the Napco Quickloader Software. See Easy Menu Programming Work-
sheet for available zone description characters.
Enter Date (Press Rto set cursor).
•Enter the current date in the format MM/DD/YY. (MM = month, DD = day and YY = year.
•Press Uto save. Press the NEXT/YES button to proceed.
Enter Time (Press Rto set cursor.)
•Enter the current time in format HH:MMA/P, where HH=hours (01–12); MM=minutes (00–59).
•Select AM or PM by pressing any number button.
•Press Uto save. Press the NEXT/YES button to proceed.
Dealer Code
•Directly enter the Dealer Code (default = 456789), using 0through 9buttons.
•Press Uto save. Re-enter the Dealer Code to verify the previous code. Press Uto save.
•Press the NEXT/YES button to proceed.
Test Timer
•Select day(s) by simply erasing the unwanted days. Move the cursor over the day and
press any number key to erase/restore the day. For example, "Monday" and "Friday" will
appear as: "• M•••F•"
•Enter Time (in 24 hour format) by moving cursor under the left H and pressing two digits to over-
write the existing default of 00. Note: Midnight is 00:00. Enter minutes by continuing to enter
data or if just updating minutes move the cursor under the left M and enter the two digits to over-
write the existing default of 00. Use Aor Ras right cursor one position.
(Direct Entry)
Enter Date
( / / )
(Direct Entry)
Enter Time
( : )
Dealer Code
456789
DEALER CODE
RE-ENTER
CLEAR PROGRAM: Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press
Cto enter the Address Program Mode; (b) access Location 2285 (Clear Program) or 2286 (Cold Start); (c) press Uand then
(d) press Cto exit the Dealer Program Mode. A “SYSTEM TROUBLE/E09-00 SERVICE” will occur. Press Cto silence the keypad.
Clear Dealer Program (Erases Dealer Program)
Use this feature to erase the Panel Program, while maintaining Scheduled Data and Zone Descrip-
tions. Access address 2285 and press U. Data entry is not allowed. NOTE: Enter Easy
Menu Driven Program Mode to reprogram system.
Cold Start (Erases Entire Program)
This erases all programmed data (Dealer Program, Zone Description Data and Schedules).
Access address 2286 and press U. Data entry is not allowed. NOTE: Some features
(schedules) can only be programmed again with the Downloading Software.
EASY MENU DRIVEN PROGRAM MODE
DATA
ENTRY
AUX 1/AUX 2
OPTIONS
0 None
1 Relay Group 1 Toggle
2 Relay Group 2 Toggle
9 Keypad Panic
A Keypad Aux.
B Instant
C PGM2 Ouput Toggle
D Access on PGM2 Output
E Arm STAY
F Interior Button
(Direct Entry)
01-
EXIT DEALER PROGRAM MODE: This completes the custom default program. Press Cto enter the Direct Address Program
Mode for further programming or press Conce again to end all programming and resume normal keypad operation.
2285 XX H
2286 XX H
TEST TIMER
SMTWTFS HH:MM

LNAPCO Security Systems XGEM-P1664EX Programming Instructions

Page 11
WI1386 5/05
DIRECT ADDRESS OVERVIEW
Direct Address Programming allows you to go directly to the address locations (up to 2287) and change the data entries
manually in order to customize your control panel options. Whereas the Easy Menu Program Mode guides you through
limited selections to get you started, Direct Address Program Mode allows you to change all options directly. It con-
sists of up to 2287 address locations each with data entry locations as shown in the following diagram (below left). The
data entry location accepts data in one of three formats: Binary, Decimal and Hexadecimal (explained below in
"Address Mode Displays"). The following diagram (below right) illustrates a Decimal format data entry location (using
a GEM-RP1CAe2 keypad).
ADDRESS MODE DISPLAYS
There are three types of address displays when programming in Direct Entry Program Mode, as follows:
A) Binary (Bit) Format
Settings (such as Zone Features) display and accept data in "number" format. For example, Zone Features are
turned on by the pressing of keypad buttons 1 through 8, with the activated Zone(s) displaying the corresponding
decimal digit (replacing deactivated zones which are signified by dashes).
EXAMPLE: BIT Format with the GEM-RP1CAe2: Program Zones 2, 4, 5 and 7 as Exit/Entry Follower Zones.
DETERMINE THE DATA ENTRIES
1. Referring to ZONE FEATURES in the Programming Worksheets that follow, the Exit/Entry Follower for Zones 1
through 8 are located at address 0916.
DATA ENTRY
LOCATION
ADDRESS
LOCATIONS
0000
0000
TO
2287
DATA ENTRY LOCATION:
(One of three formats):
•Binary (Bit)
•Decimal
•Hexadecimal
DIRECT ADDRESS PROGRAM MODE
Direct Address Program Mode
GEM-RP1CAe2 Keypad Display Example
0000 060 D
1 2
= ADDRESS LOCATION
1
2 = DATA ENTRY LOCATION
0916 - - - - - - - - B 0916 - 2 - 4 5 - 7 - B
DATA ENTRY LOCATION:
Binary (Bit) Format
•No zones yet activated
Address
0916
"Exit/Entry
Follower"
Address
0916
"Exit/Entry
Follower"
DATA ENTRY LOCATION:
Binary (Bit) Format
Press 245and 7in order to acti-
vate Zones 2, 4, 5, and 7. (The "B" on the right indi-
cates "Binary" format). Because "bit numbers"
range from 0-7, these "option numbers" 2,4,5 and 7
correspond to "bit numbers" 1,3,4 and 6, respec-
tively.

XGEM-P1664EX Programming Instructions LNAPCO Security Systems

Page 12 WI1386 5/05
PROGRAM THE DATA ENTRIES
1. Enter the panel's Dealer Security Code, then press R.
2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass
“ACTIVATE PROGRAM”, scroll backward using B.
3. Press Cto enter the Address Program Mode. Address "0000" will display.
4. Press 0916 to access Address 0916. The existing data will display and the cursor will
advance to the data field.
5. Press 678. The numbers 6,7 and 8 will appear on the keypad display indicating the zones
activated.
6. Press Uor Dto save. Address 0916 is now programmed with “6,7,8”.
7. Press Rand enter another 4-digit address to continue programming --or-- press Cto exit and resume
normal keypad operation.
B) Decimal Format
Settings (such as Entry and Exit Delay) display and accept data in decimal format, as a 3 digit number. Data is en-
tered directly, by pressing keys 0 – 9, with the cursor automatically moving to the right upon each key press.
EXAMPLE: DECIMAL Format with the GEM-RP1CAe2: Program Abort Delay to be 15 seconds.
DETERMINE THE DATA ENTRIES
1. Referring to SYSTEM DELAYS & TIMEOUTS in the Programming Worksheets that follow, the Abort Delay is
located at address 1417:
PROGRAM THE DATA ENTRIES
1. Enter the panel's Dealer Security Code, then press R.
2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass
“ACTIVATE PROGRAM”, scroll backward using B.
3. Press Cto enter the Address Program Mode. Address "0000" will display.
4. Press 1417 to access Address 1417. The existing data will display and the cursor will
Direct Address Program Mode
1417 - - - D 1417 015 D
ZONES 1 8 ZONES 9 16
ZONE FEATURES ADDR Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 ADDR Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z16
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Exit/Entry Follower 0916
6 7 8
0911
DATA ENTRY LOCATION:
Decimal Format
•No time yet entered
Address
1417
"Abort
Delay"
DATA ENTRY LOCATION:
Decimal Format
Press 015in order to set
"Abort Delay" to 15 seconds. The "D" on the
right indicates "Decimal" format.
ABORT ADDRESS 1417
DELAY
(sec.)
[Default = 0 sec. = blank (•)]
Address
1417
"Abort
Delay"

LNAPCO Security Systems XGEM-P1664EX Programming Instructions

Page 13
WI1386 5/05
Direct Address Program Mode
advance to the data field.
5. Press 015. The numbers 015 will appear on the keypad display indicating the number of
seconds entered.
6. Press Uor Dto save. Address 1417 is now programmed with a 15-second Abort Delay.
7. Press Rand enter another 4-digit address to continue programming--or--press Cto exit and re-
sume normal keypad operation.
C) Hexadecimal Format
Data such as Report Codes displays and accepts data by means of a Hexadecimal display. Data is entered di-
rectly, by pressing keys 1 – 9, G0 for zero, and G1through G5for hex B through F (11-15),
with the cursor automatically moving to the right upon key press. See table below.
EXAMPLE: HEXADECIMAL Format with the GEM-RP1CAe2: Program Chime Timeout to be 2 seconds.
DETERMINE THE DATA ENTRIES
1. Referring to SYSTEM DELAYS & TIMEOUTS in the Programming Worksheets that follow, the Chime Timeout
is located at address 1418. In the "Chime Timeout Options" table, the data entries needed to assign a time-
out of 2 seconds are "blank" and "8".
ENTRY
TOTAL
PRESS
N KEYPAD
DISPLAYS
ENTRY
TOTAL
PRESS
N KEYPAD
DISPLAYS
blank 0 • 8 8 8
1 1 1 9 9 9
2 2 2 10 G 0 0
3 3 3 11 G 1 B
4 4 4 12 G 2 C
5 5 5 13 G 3 D
6 6 6 14 G 4 E
7 7 7 15 G 5 F
HEXADECIMAL ENTRIES
CHIME ADDRESS 1418
TIMEOUT
(¼sec.)
[Default = 2 ¼sec. = ½ sec.]
DATA ENTRY LOCATION:
Decimal Format
•No time yet entered
DATA ENTRY LOCATION:
Decimal Format
Press 08in order to set "Chime
Timeout" to 2 seconds. The "H" on the right
indicates "Hexadecimal" format.
Address
1418
"Chime
Timeout"
1418 - - H 1418 - 8 H
Address
1418
"Chime
Timeout"
2 seconds
CHIME TIMEOUT OPTIONS
TIMEOUT
LEFT RIGHT
blank (•) blank (•) 0 x ¼sec. = 0 sec.
blank (•) 2 2 x¼sec. = ½ sec.
blank (•) 3 3 x ¼sec. = ¾ sec.
blank (•) 4 4 x ¼sec. = 1 sec.
blank (•) 5 5 x ¼sec. = 1.25 sec.
blank (•) 6 6 x ¼sec. = 1.5 sec.
blank (•) 7 7 x ¼sec. = 1.75 sec.
blank (•) 8 8 x ¼sec. = 2 sec.
F F 255 x ¼sec. = 63.25
DATA ENTRIES

XGEM-P1664EX Programming Instructions LNAPCO Security Systems

Page 14 WI1386 5/05
Direct Address Program Mode
PROGRAM THE DATA ENTRIES
1. Enter the panel's Dealer Security Code, then press R.
2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass “ACTIVATE
PROGRAM”, scroll backward using B.
3. Press Cto enter the Address Program Mode. Address "0000" will display.
4. Press 1418 to access Address 1418. The existing data will display and the cursor will ad-
vance to the data field.
5. Since you wish the timeout to be for 2 seconds (and 8 multiplied by ¼ second equals 2 seconds), press
08. The numbers 08 will appear on the keypad display indicating the number of seconds entered.
6. Press Uor Dto save. Address 1418 is now programmed with a 2-second chime.
7. Press Rand enter another 4-digit address to continue programming --or-- press Cto exit and resume
normal keypad operation.
PROGRAMMING CONVENTIONS USED IN THIS MANUAL
The Keypad Programming Worksheets in the back are provided as an address-programming reference to help the in-
staller modify his custom default program or to make minor field alterations to an existing panel program. It is recom-
mended that the panel be uploaded to NAPCO's PCD-Windows software following any keypad programming and that
the PCD-Windows's error-check feature be utilized to reduce the possibility of programming omissions or conflicts.
3
Keep the Keypad Programming Worksheets on file for future reference.
General Programming Steps
1. Contact the central station to ascertain receiver format, data format, event codes, subscriber numbers and tele-
phone number(s).
2. Select the desired features by circling the respective “address” boxes. Refer to the Programming Options
and Worksheets for guidance in selecting the “data” to be entered into those boxes.
3. Program the data entered in the boxes on the worksheets into the respective addresses. The display will show
the entry numerically, but if hexadecimal format will display “0” for the number 10, and letters “B”, “C”, “D”, “E”, and
“F” for the numbers 11 through 15, respectively. To program a 10, press G0. To program 11 through
15, press G1through G5, respectively.
The displays will appear after a brief delay.
Use Rto toggle the cursor between the 4-digit address field and the data entry locations.
Enter the address directly using the number buttons.
The contents of the address will be read automatically. The cursor will advance to the data field. Enter the re-
quired data directly using the number buttons.
IMPORTANT: Press Uor Dto save the contents of each address.
EXIT DIRECT ADDRESS PROGRAM MODE: When done, press Cto exit and resume normal keypad operation.

LNAPCO Security Systems XGEM-P1664EX Programming Instructions

Page 15
WI1386 5/05
SYSTEM DELAYS & TIMEOUTS (ADDRESS 0000-0002, 1413, 1417, 2050 & 2055)
Direct Address Program Mode
WARNING: Timers have uncertainty of +/-1 sec, so a "time" of 1 second may actually timeout IMMEDIATELY.
Select delay/timeout (0-255 sec.).
EXIT/ENTRY DELAYS: Apply only to zones programmed with the following options “Exit/Entry 1, Exit/Entry
2, Exit/Entry Follower”. NOTE: Sensor Watch Time Options are similar to above, except in hours.
Press Uor Dto save.
SYSTEM DELAYS & TIMEOUTS (ADDRESS 1418-1419)
DEFAULTS: The defaults shown on this
page and on the following pages are
automatically set after exiting the Easy
Menu Driven Mode.
1. Enter delay/timeout in corresponding address locations above.
Note: All entries for address 1418 are in quarter seconds (.25 seconds).
Therefore, the default of 008 results in a 2 second timeout.
2. Press Uor Dto save.
EXIT ADDRESS 0000
DELAY
(sec.)
[Default = 060]
ENTRY ADDRESS 0001
DELAY 1
(sec.)
[Default = 030]
PGM2 Output ADDRESS 1413
Access Cntrl
Timeout (sec.)
[Default = 0 sec. = blank (•)]
ABORT ADDRESS 1417
DELAY
(sec.)
[Default = 030]
Sensor Watch ADDRESS 2050
Time
(Hrs.)
[Default = 024]
Report Cancel ADDRESS 2055
Window
(min.)
[Default = 0 min. = blank (•)]
AC Fail ADDRESS 1419
Report Delay
(min.)
[Default = 060]
CHIME ADDRESS 1418
TIME
(¼sec.)
[Default = 008 x ¼ sec. = 2 sec.]
ENTRY ADDRESS 0002
DELAY 2
(sec.)
[Default = 030]

XGEM-P1664EX Programming Instructions LNAPCO Security Systems

Page 16 WI1386 5/05
SYSTEM OUTPUT TIMEOUTS (ADDRESS 1412 & 1414-1416)
1. Select delay/timeout (0-255 min.) from the table shown.
2. Enter in corresponding address locations above.
3. Press Uor Dto save.
OUTPUT TIMEOUTS: If a timeout of “0 min.” is selected, then the output will remain active (ON)
until the system is reset or disarmed.
DOWNLOAD/CALLBACK OPTIONS (ADDRESS 2059 & 0526-0545)
NUMBER OF RINGS BEFORE PICKUP: Enter the number of rings before automatic
pickup by the control panel when downloading from a computer (see Glossary at the back
for more information).
1. Enter digit only.
2. Valid entries are: 003-015. NOTE: Default is 15 Rings.
3. Press Uor Dto save.
CALLBACK TELEPHONE NUMBER: Enter telephone number to be used when downloading from a computer (see Glossary at
the back for more information).
1. Enter digit only (right nibble).
2. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•).
3. Valid entries are: 1-9, B = *button, C = #button, D = 3 sec. pause, E = Wait for dial tone, F = ignore location.
4. Press Uor Dto save.
PAGER FORMAT OPTIONS (ADDRESS 0546 & 0547)
LEADING DIGITS FOR PAGER FORMAT: In Pager Format reporting, the message typically begins with “00”.
However, for some pager services, this will cause the Pager's Voice Mail feature to activate. This option allows
you to program these digits to any number desired. A typical Pager report is “003 22 1234”, where 3 is the Event,
22 is the zone, and 1234 is the Subscriber ID number. For example, if the Leading Digits are programmed as “98”,
the Pager report will now appear as “983 22 1234”. NOTE: See CS Receiver Options to select Pager Format.
1. Enter in 1st and 2nd Leading Digits as shown (right nibble).
2. Valid entries are: 0-9. Press Uor Dto save.
Callback
Telephone
Number
ADDRESS 0526-0545 (RIGHT DIGITS 1-20)
0526 0527 0528 0529 0530 0531 0532 0533 0534 0535 0536 0537 0538 0539 0540 0541 0542 0543 0544 0545
(Digits 1-20)
[Default = blank (•) for all digits 1-20]
No. Rings ADDRESS 2059
Before
Pickup
[Default = 015 ]
PGM2 ADDRESS 1412
Output
Timeout (min.)
[Default = 0 min. = blank (•)]
Alarm ADDRESS 1414
Output
Timeout (min.)
[Default = 015]
Pulse Alarm ADDRESS 1415
Output
Timeout (min.)
[Default = 015]
PGM1 ADDRESS 1416
Output
Timeout (min.)
[Default = 0 min. = blank (•)]
DELAY/
TIMEOUT
blank (•) 0 min.
001 1 min.
002 2 min.
003 3 min.
004 4 min.
005 5 min.
006 6 min.
016 16 min.
255 255 min.
DATA
ENTRIES
Leading Digits for ADDRESS 0546
Pager Format
(1st Digit)
Leading Digits for ADDRESS 0547
Pager Format
(2nd Digit)
[Default = blank (•) blank (•)]
Direct Address Program Mode

LNAPCO Security Systems XGEM-P1664EX Programming Instructions

Page 17
WI1386 5/05
GLOBAL SYSTEM EVENT/TROUBLE
SYSTEM RESPONSE
ACTIVATED BY GLOBAL
EVENT/TROUBLE
ADDR TEST
TIMER
TELCO
FAILURE
RF RCVR.
TROUBLE
MEMORY
FAILURE
LOW
BATTERY AC FAIL EZM TAMPER
Bell
Superv
1 2 3 4 5 6 7 8
Alarm Output 0836
Pulsed Alarm Output 0837
PGM1 Output 0838
PGM2 Output 0839
Report Event Telco 1 0840
Report Restore Telco 1 0841
Report Event Telco 3 0842
Report Restore Telco 3 0843
SYSTEM OPTIONS (ADDRESS 0836-0871 & 2045)
1. Select the desired option entering the option number (1-8) for each digit.
2. Enter corresponding option number in address location.
NOTE: Dark shaded data value box shows option not available. Press Uor Dto save.
GLOBAL AMBUSH CODE: It is the 2-digits entered immediately prior to the regular disarm code. If
“Enable Global Ambush Code” (Address 1422) is selected and Address 2045 is left blank (•), then the
2-digit Global Ambush Code is “99”. If “Enable Global Ambush Code” is selected and Address 2045
is not left blank (•), then the 2-digit Global Ambush Code is the two digits entered in address 2045.
Enter in address location (both 1st and 2nd digits); valid entries are 1-9.
Press Uor Dto save.
Direct Address Program Mode
[Default = blank (•) blank (•)]
Global 1st digit 2nd digit
Ambush Code
ADDRESS 2045
SYSTEM RESPONSE
ACTIVATED BY AREA 1
EVENT/TROUBLE
AREA 1 SYSTEM EVENT/TROUBLE
ADDR AMBUSH KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX. KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE Keyfob
Low Batt
1 2 3 4 5 6 7 8
Pulsed Alarm Output 0856
Alarm Output 0857
PGM1 Output 0858
PGM2 Output 0860
Report Event Telco 1 0861
Report Event Telco 3 0863
[Default = blank (•) from address 0856-0863]
SYSTEM RESPONSE
ACTIVATED BY AREA 2
EVENT/TROUBLE
AREA 2 SYSTEM EVENT/TROUBLE
ADDR AMBUSH KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX. KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE Keyfob
Low Batt
1 2 3 4 5 6 7 8
Pulsed Alarm Output 0864
Alarm Output 0865
PGM1 Output 0866
PGM2 Output 0868
Report Event Telco 1 0869
Report Event Telco 3 0871
[Default = blank (•) blank (•) from address 0864-0871]
[Default = blank (•) from address 0836-0843]. Note: If Test Timer is enabled (above), Digital Dialer Test is also enabled.

XGEM-P1664EX Programming Instructions LNAPCO Security Systems

Page 18 WI1386 5/05
SYSTEM OPTIONS (ADDRESS 0872-0887)
1. Select the desired option entering the option number (1-8) for each digit.
2. Enter corresponding option number in address location.
NOTE: Dark shaded data value box shows option not available. Press Uor Dto save.
Direct Address Program Mode
SYSTEM RESPONSE
ACTIVATED BY AREA 3
EVENT/TROUBLE
AREA 3 SYSTEM EVENT/TROUBLE
ADDR AMBUSH KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX. KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE Keyfob
Low Batt
1 2 3 4 5 6 7 8
Pulsed Alarm Output 0872
Alarm Output 0873
PGM1 Output 0874
PGM2 Output 0876
Report Event Telco 1 0877
Report Event Telco 3 0879
[Default = blank (•) from address 0872-0879]
SYSTEM RESPONSE
ACTIVATED BY AREA 4
EVENT/TROUBLE
AREA 4 SYSTEM EVENT/TROUBLE
ADDR AMBUSH KEYPAD
PANIC
KEYPAD
FIRE
KEYPAD
AUX. KEYPAD
TAMPER
FAIL TO
OPEN
FAIL TO
CLOSE Keyfob
Low Batt
1 2 3 4 5 6 7 8
Pulsed Alarm Output 0880
Alarm Output 0881
PGM1 Output 0882
PGM2 Output 0884
Report Event Telco 1 0885
Report Event Telco 3 0887
[Default = blank (•) blank (•) from address 0880-0887]

LNAPCO Security Systems XGEM-P1664EX Programming Instructions

Page 19
WI1386 5/05
SYSTEM OPTIONS (ADDRESS 1420-1424, 2051-2054)
*NOTE: Address 1423: Default depends on Easy Menu Question :“EZ
ZONE DOUBLING? Y/N”. If yes, then [Default = 1]. If no, then [Default =
blank (•)].
**NOTE: To select “Line-Fault Test only when Armed”, you must also se-
lect “Enable Line-Fault Test” at address 1423.
***NOTE: If “Enable Global Ambush Code” in Address 1422 is selected, then
program the 2-digit “Global Ambush Code” in Address 2045. If Address
2045 is left blank (•), then, the 2-digit “Global Ambush Code” will be “99”.
****Note: If this feature is not selected, the E15 Lug will, by default,
activate when the system is armed (all areas).
1420 System Options 1421
Default
Option Default Option
OFF 1 Opening Report Only after Alarm Report OFF 1 Auto Bell Test on Arming
OFF 2 Closing Report Only on Conditional Close OFF 2 Auto Reset after Burglary Output Timeout
OFF 3 Incl. Sel./Grp. Bypass in Cond. Close /Status OFF 3 Suppress Bypass Reminder when Armed
OFF 4 Status Report OFF 4 Enable Local Alarm on First Zone AND Trip
OFF 5 RESERVED OFF 5 Access Control on PGM2 Output
OFF 6 Enable AutoArm if not closed at end of Window OFF 6 Maintained Keyswitch Arming
OFF 7 Enable Keypad Time/Date Display OFF 7 Enable Manager's Mode
OFF 8 Disable Zone Fault Scrolling OFF 8 Disable Keypad Instant Mode
System Options
1422 System Options 1423 System Options
Default Option Default* Option
OFF 1 Interior Normally Bypassed OFF* 1 Enable Zone Doubling (Zones 9-16)
OFF 2 Enable Global Ambush Code *** OFF* 2 Wireless Trouble Activates Telco 1
OFF 3 Reset Day Zone with Arm/Disarm Only OFF* 3 Wireless Trouble Activates Telco 3
OFF 4 Enable Residential Fire OFF* 4 Enable Alarm Output on Telco Fail only when Armed
OFF 5 Disable Keypad Function Mode Download OFF* 5 Line-Fault Test only when Armed**
OFF 6 Disable Callback Download OFF* 6 Enable Line-Fault Test**
OFF 7 Chirp Output on Keyfob Arm/Disarm OFF* 7 Inhibit System Trouble Audible at Keypad
OFF 8 Change Pulse Output to Temporal Output§OFF* 8 Select Alarm Output for Keyfob Chirp
§This feature must be programmed in Fire Alarm applications.
2051 System Options
Default Option
OFF 1 Enable Keypad Set Time/Date Message
OFF 2 Enable Cancel Report to Telco 3
OFF 3 Disable [ON/OFF] as Easy Exit
OFF 4 Enable GEM-PRINT Module
OFF 5 RESERVED
OFF 6 RESERVED
OFF 7 Disable System Trouble Audible Timeout
OFF 8 Enable "K Series" Style Keypads ††
†† NOTE: For reference only and cannot be changed.
1424
Default Option
OFF 1 Automatic Interior Bypass/Easy Exit
OFF 2 Veri-phone Zones Trip PGM2 Output
OFF 3 Veri-phone Audio Priority Over Alarms
OFF 4 Resound on Wireless Smoke Low Battery
OFF 5 Don't Clear PGM2 Output with Disarm
OFF 6 Disable 2nd Call Ans. Machine Override
OFF 7 Enable Loop Supervision
ON 8 Disable Code Required for EZ Bypass
System Options
Direct Address Program Mode
2053
Default Option
OFF 1 Exit Time Restart
OFF 2 Sound Alarm On Exit Error
OFF 3 Rpt Exit Err/Recent Close
OFF 4 Enable CP-01 Limits
OFF 5 Digital Dialer Rpt Enter /Exit Test Mode
OFF 6 Disable Call Waiting on 1st Attempt
OFF 7 Enable Keypad 1 Only Programming
OFF 8 Enable CP-01 Egress Tones Only
System Options
2054
Default Option
OFF 1 Enable TCP/IP Communications
OFF 2 Enable EN501 User Code Access Level
OFF 3 RESERVED
OFF 4 Enable Display Time On Blanked Keypads
OFF 5 Enable EN501 Grade 3 Operation
OFF 6 RESERVED
OFF 7 Enable 2-Count Swinger Shutdown
OFF 8 Enable Keypad Blanking
System Options
2052 E15 Lug / System Options
Default Option
OFF 1 RESERVED
OFF 2 RESERVED
OFF 3 Lug E15 Area 1 Armed Away Only****
OFF 4 PGM on RF Transmitter Tamper
OFF 5 RESERVED
OFF 6 RESERVED
OFF 7 RESERVED
OFF 8 RESERVED

XGEM-P1664EX Programming Instructions LNAPCO Security Systems

Page 20 WI1386 5/05
Direct Address Program Mode
NOTE: * See Pager Format Options to program
Leading Digits for Pager Format.
CS RECEIVER OPTIONS (ADDRESS 0460-0525)
Default for CS Receiver 1 Format depends on Easy Menu Question “RCVR FORMAT”. [Default = •(blank) •
(blank)] for CS Receivers 2 and 3 Formats.
CS RECEIVER FORMATS: Up to 3 CS Formats may be programmed.
1. Select the desired CS Receiver Format from the table shown.
2. Enter the corresponding digit in the address location for each CS Receiver. NOTE:
Dark
shaded data value box shows option not available. Press [Enter] of [ON/OFF] to save.
DATA
ENTRY
CS RECEIVER 1 FORMAT
blank (•) Ademco Slow, Silent Knight Slow
2 Radionics Fast
3 Silent Knight Fast
4 Radionics, DCI, Franklin Slow
5 Universal High Speed
B SIA
C Ademco Point ID
E Pager *
CS RECEIVER OPTIONS:
Select options for any of the three CS Receivers.
1. Select the desired option entering the option number
(1-8) for each digit.
2. Enter corresponding option number in address
location (right nibble).
NOTE: Dark shaded data value box shows option not avail-
able. Press [Enter] or [ON/OFF] to save.
*NOTE: If both are selected, 1400Hz has priority over 2300Hz.
CS RECEIVER TELEPHONE NUMBERS: Enter telephone numbers for any of the three CS Receivers (Telco 1, 2 & 3).
1. Enter digit only.
2. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•). Press [Enter] or [ON/OFF] to save.
3. Valid entries are: 1-9, B = *button, C = #button, D = 3 sec. pause, E = Wait for dial tone, F = Ignore location
Default for CS
Receiver 1 Tele-
phone Number
depends on Easy
Menu Question
“CENTRAL
PHONE #”.
[Default = blank (•)]
across digits 1-20
for CS Receiver
Telephone Num-
bers 2 and 3.
ADDRESS 0460
CS Receiver 1
Format
ADDRESS 0482
CS Receiver 2
Format
ADDRESS 0504
CS Receiver 3
Format
ADDRESS 0462-0481 (RIGHT DIGITS 1-20)
0462 0463 0464 0465 0466 0467 0468 0469 0470 0471 0472 0473 0474 0475 0476 0477 0478 0479 0480 0481
(Digits 1-20)
CS Receiver 1
Telephone
number
CS Receiver 2
Telephone
Number
ADDRESS 0484-0503 (RIGHT DIGITS 1-20)
0484 0485 0486 0487 0488 0489 0490 0491 0492 0493 0494 0495 0496 0497 0498 0499 0500 0501 0502 0503
(Digits 1-20)
CS Receiver 3
Telephone
Number
ADDRESS 0506-0525 (RIGHT DIGITS 1-20)
0506 0507 0508 0509 0510 0511 0512 0513 0514 0515 0516 0517 0518 0519 0520 0521 0522 0523 0524 0525
(Digits 1-20)
0461 CS Receiver Options - Telco 1 0483
Default Option Default Option
OFF 1 1400Hz Handshake/Kissoff * OFF 1 1400Hz Handshake/Kissoff *
OFF 2 2300Hz Handshake/Kissoff * OFF 2 2300Hz Handshake/Kissoff *
OFF 3 Enable Zone Number on Pulse Alarm OFF 3 Enable Zone Number on Pulse Alarm
OFF 4 Single Digit Only OFF 4 Single Digit Only
OFF 5 Sum Check OFF 5 Sum Check
OFF 6 3/1 with Extended Restores OFF 6 3/1 with Extended Restores
OFF 7 RESERVED OFF 7 RESERVED
OFF 8 RESERVED OFF 8 RESERVED
CS Receiver Options - Telco 2
0505
Default Option
OFF 1 1400Hz Handshake/Kissoff *
OFF 2 2300Hz Handshake/Kissoff *
OFF 3 Enable Zone Number on Pulse Alarm
OFF 4 Single Digit Only
OFF 5 Sum Check
OFF 6 3/1 with Extended Restores
OFF 7 RESERVED
OFF 8 RESERVED
CS Receiver Options - Telco 3